Eaton xComfort GSM Modem CKOZ-00/02 / CKOZ-00/06 Assembly Instructions
Brand: Eaton
Product: xComfort GSM Modem
Models: CKOZ-00/02, CKOZ-00/06
Technical Specifications: GSM 900/1800 Mhz, Dualband GPRS Class 8
Operating Temperature: -25°C to +70°C (Modem), -20°C to +55°C (Antenna)
Ingress Protection: IP20
Important Safety Information
Danger: Risk of death. Installation must be performed only by qualified electricians.
- Installation only by electricians.
- Montage nur durch Elektrofachkräfte.
- Montage uniquement par un électricien.
- Montáž pouze osobami s elektrotechnickou kvalifikací.
- Montáž iba osobami s elektrotechnickou kvalifikáciou.
- Må kun installeres af en aut. el-installatør.
- Debe ser instalado por un profesional eléctrico.
- Csak szakképzett személy szerelheti.
- Montaggio esclusivamente ad opera di personale specializzato.
- Må monteres av autorisert installatør Gr.L.
- Montage alleen door elektromonteurs.
- Deve ser instalado por um profissional.
- Montaz tylko przez uprawnionych instalatorów.
- Får endast utföras av behörig elektriker.
- Asennus vain sähköasentajan toimesta.
- Sadece uzman kisiler monte edebilir.
- Instalare numai de catre electricieni.
- Монтаж может производить только электрик.
- Εγκατάσταση μόνο από ηλεκτρολόγους.
- 仅允许合格电气技师进行安装.
- تعليمات التركيب
- خطر على الحياة
- التركيب فقط من قبل عمال كهرباء اختصاصيين
Installation Steps
- Antenna Placement: Ensure the antenna is placed with a clear line of sight, approximately 2.5 meters from the modem. The antenna cable length is approximately 1.8 meters.
- SIM Card Installation: Insert the SIM card into the modem. Ensure the SIM card is version 1.30 or higher.
- SIM Card and PIN Entry: Insert the SIM card and enter the PIN if required.
- Modem Connection: Connect the SIM card to the modem.
- Antenna Positioning: Position the antenna away from ferrous materials (Fe) for optimal signal reception. A checkmark [✔️] indicates correct placement.
- Connecting the Modem: Connect the modem to the power supply (230VAC, 50Hz) and the antenna.
- Power Connection: Connect the power adapter to the wall socket and then to the modem.
- Cable Connection: Connect the antenna cable to the modem. Ensure the connection is secure.
- Modem Initialization: The modem will initialize. The display will show "Modem ok" after approximately 1 minute.
RF System Modes
The RF system supports different modes: BASIC, MODE, and CARD. The following diagrams illustrate various configurations and their operational status (indicated by checkmarks [✔️] or crosses [❌]).
Basic Mode Configurations:
- CTAA-01/01
- CTAA-02/01
- CBEU-02/01
- CSAU-01/01
- CBEU-02/02
- CJAU-01/01
- CDAU-01/01
- CRCA-00/01
- CHSZ-00/01
Mode Card Configurations:
- CSAU-01/01
- CJAU-01/01
- CDAU-01/01
Diagrams illustrating various operational sequences and system states are provided, showing combinations of button presses (PROG, MODE) and timing (e.g., <0.5s, >5s, 10s) for different functions.
