Huuger 8718 Instruction Manual

About Us

Some "HUUGER" moments may cure you of everything. Derived from the Danish term "Hygge", HUUGER conveys happiness and contentment to every family. HUUGER is devoted to creating a cosy corner at home. Surrounded by pieces of furniture you love, and relax in mind. We hope some HUUGER home moments can free you from a busy life. Creating a satisfying home corner doesn't mean it costs much. That's why HUUGER always focuses on high-quality, practical, and reasonably-priced products.

Matters Needing Attention

• You need a helper to finish the installation.
• Don't over-tighten the screws until all the parts are in place. Failure to follow the instructions may cause misalignment of the screws.
• DO NOT let children climb the product.
• To avoid suffocation danger, keep small parts and package materials away from children.
• Adult assembly required. Keep children away during the installation.
• Children should not use it without parents' supervision.
• You could use "corner guard" to protect children from getting hurt by the edges.
• If any parts were missing, broken or wrongly delivered, contact Huuger immediately via email: service@huuger.com.

Part List

Hardware

Assembly Instruction

Step 1

Attach parts 3 and 4 to the base structure using part A.

(Diagram shows two vertical frame structures being assembled with screws.)

Step 2

Connect parts 7 and 8 using parts G and C. Ensure correct alignment.

(Diagram shows horizontal bars being attached to vertical frames with screws and brackets.)

Step 3

Note: The screws connecting two parts 7 are facing downwards, and the same applies to the screws connecting two parts 8. Attach parts 3 and 4 to the assembled frame using part D.

(Diagram shows the frame structure being reinforced with screws.)

Step 4

Attach parts 5 and 10 to the frame using part B.

(Diagram shows shelves and support bars being attached to the frame.)

Step 5

Insert part 9 into the top of the frame and secure with part D. Attach part 5 to the frame using part D.

(Diagram shows vertical supports being added and secured.)

Step 6

Note: The direction of the metal pieces on parts 5 is consistent with that of the parts 3 and 4. Secure the structure using part D.

(Diagram shows the main frame being further secured.)

Step 7

Note: The sizes on both sides of this hole are different. Please place the bigger side facing upwards and the smaller side facing downwards. Connect part 2 using parts E and F.

(Diagram shows the top panels being attached.)

Step 8

Secure the entire structure using part D.

(Diagram shows the final tightening of screws throughout the cabinet.)

Step 9

Connect the top panels (part 1) using part L.

(Diagram shows the top surfaces being joined.)

Step 10

Note: Please tighten the screws in order from the middle to both sides.

(Diagram shows the final tightening of screws on the top panels.)

Step 11

Attach parts 6 to the frame using parts F and D.

(Diagram shows additional supports being added.)

Step 12

Assemble the drawers using parts 11 and 12, securing them with part B and H.

(Diagram shows the drawer assembly process.)

Step 13

Insert the assembled drawers into the cabinet.

(Diagram shows drawers being slid into the cabinet.)

Step 14

Wall Mounting:

Use parts J to secure the cabinet to the wall for stability. Ensure the cabinet is level before proceeding.

(Diagram shows the cabinet being anchored to a wall using screws and brackets.)

Troubleshooting

Possible problems during installation:

• Gap between boards: Ensure boards are properly aligned.
• Misaligned holes: Loosen screws, adjust boards for a gap-free fit, then retighten. The larger hole in the bar allows for adjustment.

If the above method doesn't work, please contact Huuger with a photo of the holes for further assistance.

Help Center

Please contact Huuger first if you have any problem!

✉ www.huuger.com

? service@huuger.com

WARNINGS

Huuger does not assume any and all responsibility or liability from personal injury, property damage or loss, whether direct or indirect, or incidental, resulting from the incorrect instruction, improper use, inadequate maintenance, or neglect of this product.