Red Sea REEFER NANO/170 Cabinet Installation Guide
This guide provides step-by-step instructions for assembling the Red Sea REEFER NANO/170 aquarium cabinet.
Parts List
| Part Label | Description | Quantity |
|---|---|---|
| A | Base Panel | 1 |
| B | Left Side Panel | 1 |
| C | Top Panel | 1 |
| D | Back Panel | 1 |
| E | Shelf Panel | 1 |
| F | Front Door Panel | 1 |
| G | Rear Door Panel | 1 |
| H | Support Frame | 2 |
| L | Hinges | 2 |
| M | Bolts | 30 |
| N | Dowels | 32 |
| O | Screws (ST3.9 x 16) | 12 |
| P | Cam Locks | 30 |
| R | Brackets | 1 |
| S | Drawer Slides | 1 |
| T | Screws (ST3.5 x 14) | 2 |
| Y | Cam Lock Pins | 18 |
Assembly Instructions
Step 1: Prepare Base Panel (A)
Insert dowels (N) into panel A using a [Hammer]. Screw cam lock pins (Y) into panel A using a [Screwdriver]. Bolts (M) are indicated for use with an [Allen Key].
Diagram shows panel A with dowels (N) being inserted, cam lock pins (Y) being screwed in, and bolts (M) indicated for later use.
Step 2: Attach Support Frames (H) to Base (A)
Attach two support frames (H) to the base panel (A) using cam locks (P) and cam lock pins (Y). Quantity: 4 sets (Px4, Yx2).
Diagram shows two vertical support frames (H) being attached to the base panel (A) using cam lock mechanisms (P and Y).
Step 3: Prepare Side Panel (B)
Insert dowels (N) into panel B using a [Hammer]. Screw cam lock pins (Y) into panel B using a [Screwdriver]. Bolts (M) are indicated for use with an [Allen Key].
Diagram shows panel B with dowels (N) being inserted and cam lock pins (Y) being screwed in.
Step 4: Attach Side Panel (B)
Attach the prepared side panel (B) to the base assembly using cam locks (P) and cam lock pins (Y). Quantity: 4 sets (Px4, Yx2).
Diagram shows panel B being attached to the base assembly (A and H) using cam lock mechanisms (P and Y).
Step 5: Prepare Top Panel (C)
Insert dowels (N) into panel C using a [Hammer]. Screw cam lock pins (Y) into panel C using a [Screwdriver]. Bolts (M) are indicated for use with an [Allen Key].
Diagram shows panel C with dowels (N) being inserted and cam lock pins (Y) being screwed in.
Step 6: Attach Shelf Panel (E)
Attach the shelf panel (E) to the side panel assembly using cam locks (P) and cam lock pins (Y). Quantity: 2 sets (Px2, Yx2).
Diagram shows shelf panel (E) being attached to the side panel assembly using cam lock mechanisms (P and Y).
Step 7: Attach Back Panel Assembly
Assemble the back panel structure using cam locks (P) and cam lock pins (Y). Quantity: 2 sets (Px2, Yx2).
Diagram shows components of the back panel assembly being joined using cam lock mechanisms (P and Y).
Step 8: Prepare Base Panel (F)
Insert dowels (N) into panel F using a [Hammer]. Screw cam lock pins (Y) into panel F using a [Screwdriver]. Bolts (M) are indicated for use with an [Allen Key].
Diagram shows panel F (likely another base or structural panel) with dowels (N) and cam lock pins (Y) being inserted.
Step 9: Assemble Main Cabinet Structure
Assemble the main cabinet frame using bolts (M) and dowels (N). Attach bracket (R) using screws (T). Quantity: 2 screws (Tx2).
Diagram shows the main cabinet structure being assembled with bolts (M) and dowels (N). A bracket (R) is shown being attached with screws (T).
Step 10: Install Internal Dividers/Supports
Install internal components using cam locks (P) and cam lock pins (Y). Quantity: 7 sets (Px7, Yx3).
Diagram shows internal parts of the cabinet being assembled using cam lock mechanisms (P and Y).
Step 11: Install More Internal Dividers/Supports
Install further internal components using cam locks (P) and cam lock pins (Y). Quantity: 7 sets (Px7, Yx3).
Diagram shows additional internal parts of the cabinet being assembled using cam lock mechanisms (P and Y).
Step 12: Attach Side/Back Panels
Attach side and back panels to the main structure using cam locks (P) and cam lock pins (Y). Quantity: 6 sets (Px6, Yx6).
Diagram shows side and back panels being secured to the cabinet frame using cam lock mechanisms (P and Y).
Step 13: Install Doors (D) and Hinges (L)
Attach hinges (L) to the door panel (D) using screws (O). Quantity: 2 hinges (Lx2), 12 screws (Ox12).
Diagram shows hinges (L) being attached to door panel (D) using screws (O).
Step 14: Mount Doors
Mount the assembled doors onto the cabinet frame.
Diagram shows the cabinet with doors being attached.
Step 15: Adjust Hinges
Adjust the hinges for proper door alignment.
Diagram illustrates how to adjust hinges for optimal door fit.
Step 16: Install Drawer Slides (S)
Attach the drawer slides (S) to the cabinet interior. Quantity: 1 set.
Diagram shows drawer slides (S) being attached to the inner side of the cabinet.
Support and Contact Information
For assistance or inquiries, please contact the Red Sea office in your region:
- Europe: Red Sea Europe, 655 Rue des Frères Lumière, 27130 Verneuil d'Avre et d'Iton, France. Email: support.fr@redseafish.com
- UK & Ireland: Red Sea Aquatics (UK) Ltd, PO Box 1237, Cheddar, BS279AG. Email: uk.info@redseafish.com
- U.S.A: Red Sea U.S.A, 4687 World Houston Parkway #150, Houston, TX 77032, U.S.A. Email: support.usa@redseafish.com
- Germany & Austria: Red Sea Deutschland, Büro Deutschland, Prinzenallee 7 (Prinzenpark), 40549 Düsseldorf. Email: support.de@redseafish.com
- China: Red Sea Aquatics (GZ) Ltd, Block A3, No.33 Hongmian Road, Xinhua Industrial Park, Huadu District, Guangzhou City, China, Postal code 510800. Tel: +86-020-6625 3828
Model Number: #5346 REEFER NANO/170_v19A
