Vibe Travel Bass Wireless LED Speaker Quick Start Guide

Charging the Speaker

⚡ Charge the speaker before using it for the first time.

⏰ Plug in the cable to the micro USB port and charge for 2 hours.

Connect the charging cable to charging port.

A visual representation shows a USB-A connector on one end and a Micro USB connector on the other, connected by a cable. An arrow points from the Micro USB connector to a diagram of the speaker's charging port, highlighting a Micro USB input port.

Features/Parts

An illustration of the Vibe Travel Bass Wireless LED Speaker with numbered callouts pointing to its various parts: 1. Retractable Trolley Handle, 2. Carrying Handle, 3. Mic Volume Adjustment Knob, 4. Optional Mic Input, 5. Volume Adjustment Knob, 6. DC 5V / USB Charging Port, 7. Power On/Off, 8. Optional AUX-In, 9. SD Card Reader, 10. LED Display Panel, 11. USB Reader, 12. Mode Button, 13. Previous Track, 14. Play/Pause, 15. Next Track. The front shows 16. LED Light Panel / Speaker. The rear shows 17. 2 Castor Wheels.

• 1. Retractable Trolley Handle
• 2. Carrying Handle
• 3. Mic Volume Adjustment Knob
• 4. Optional Mic Input
• 5. Volume Adjustment Knob
• 6. DC 5V / USB Charging Port
• 7. Power On/Off
• 8. Optional AUX-In
• 9. SD Card Reader
• 10. LED Display Panel
• 11. USB Reader
• 12. Mode Button
• 13. Previous Track
• 14. Play/Pause
• 15. Next Track
• 16. LED Light Panel / Speaker
• 17. 2 Castor Wheels (Rear of speaker)

NOTE: To switch between AUX, FM, BT, USB and SD modes, press the "Mode" button.

Pairing Your Speaker

Your speaker will work best if it is within 30 ft. of your smart device. You may experience sound briefly cutting off if you are out of range or if your wireless connection is weak. Make sure Bluetooth is enabled on your smart phone or tablet before starting the pairing process.

Step 1: Power On

An image shows the side of the speaker with the power switch in the 'On' position. A blue circle highlights the charging port area, indicating the speaker is ready to connect.

Turn on the speaker by flipping the Power Switch to the "On" position. The speaker will "beep" when it is ready to connect.

Step 2: Connect via Bluetooth

An image displays a smartphone screen showing a list of available Bluetooth devices. 'DG-17KR' is highlighted, indicating it is the device to select for pairing.

From your smart phone or tablet, find a list of nearby devices and choose "DG-17KR". Enter "0000" if asked. The speaker will "beep" again when pairing is complete!

Specifications

• Bluetooth®: V5.0
• Impedance: 3 Ohms
• Speaker Frequency: 150HZ~18KHz
• FM Channel Range: 87.5-108.0MHZ
• Play Time: 1.5 hours
• Speaker Power: 10W
• Battery: 1500mAh
• Charging Time: 5 - 6 hours

Warning

• Keep away from water and moisture.
• Keep away from heat sources.
• Do not disassemble.

FCC ID: 2AANZ17KR

BT ID: D044460

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.