Sim-Lab
Installation Guide for SIM-LAB models including: P1X Pro Cockpit, P1X, Pro Cockpit, Cockpit
– Sim-Lab
P1X Pro Sim Racing Cockpit – Sim-Lab
File Info : application/pdf, 27 Pages, 1.68MB
DocumentDocumentINSTRUCTION MANUAL P1X PRO COCKPIT VERSION 1.09 Last updated: 14-04-2025 BEFORE YOU START: Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions on assembly. This requires only a set of simple tools and some of your time. Please check the bill of materials before starting (pages 23/24) and make sure all the parts are delivered. For the angled profiles, the lengths in the bill of materials might not perfectly match the length of the part you measure. Don't worry, we measure differently when cutting the profiles and with the angles as they are, the given dimensions are a close approximation. We tried to go with a different style of assembly for this one. Don't panic if you can't find any corner brackets included in the hardware bags. Inserting Slot-Nuts: You got excited, finished the build, put the caps on, but forgot to install one element. Do not worry. It happens to everyone. In this diagram, you can see how to insert a Slot-Nut directly into the slot from the side. You can also use one of your smaller Hex wrenches to help wiggle the Slot-Nut in place. Tools needed: 5/6MM 24MM 22 | 27 1350MM 500MM M8 X 40 Washer M8 (DIN 988) 2X 1X 4X 4X Note: the counterbores should point (arrows) to the outside of the cockpit. A2 A1 B18 B13 33 | 27 490MM Corner Bracket M8 X 20 1X 2X 4X A3 B3 B15 44 | 27 Profile 160x40 End-Cap M8 X 20 Slot-Nut M8 2X 4X 8X B26 B4 B15 55 | 27 Foot Foot Support Plate Nut M16 Washer M16 BUILD BOTH Foot Foot Support Plate VERSIONS 2X Nut M16 Washer M16 1X 1X 2X 2X B25 B24 1X 1X 2X 2X B21 B22 66 | 27 M8 X 25 8X B23 77 | 27 A5 B13 B18 B8 B20 500MM Profile 40X40 End-Cap M8 X 40 Washer M8 Slot-Nut M8 (DIN 988) 2X 4X 4X 4X 4X 88 | 27 450MM 450MM Pedal Deck Bracket Cap-Washer M8 X 30 M8 Washer M8 (DIN 988) 1X 1X 2X 8X 8X 8X C2 C3 C5 C10 C9 C1 99 | 27 Cap-Washer M8 M8 X 40 Washer M8 Slot-Nut M8 (DIN 988) 4X 4X 4X 4X C10 C8 C9 C4 1100 | 27 B16 B9 850MM Profile 120X40 End-Cap Angled Upright Sandwich LEFT M8 X 20 Slot-Nut M8 1X 2X 1X BUILD 2X 4X 4X B20 B5 A4 Part B9 is is angled, therefore only fits on the LEFT side of the cockpit. For the RIGHT side of the upright assembly, see the next page. 1111 | 27 B20 B14 B18 B17 Cap-Washer M8 X 25 M8 Washer M8 Slot-Nut M8 (DIN 988) 8X 8X 8X 8X B10 1122 | 27 Wheel Deck 1X M8 X 50 (D2) 2X M8 X 20 (D3) Washer M8 Slot-Nut M8 If you purchased the `Front Mount', please see the next page. Normal assembly resumes with the `Side Mount' on page 19. 2X 4X 4X D1 D2 D5 D4 D3 1133 | 27 E1 Front Mount Bracket A Front Mount Bracket B Front Mount Spacer M8 X 25 2X 2X 2X 8X 8X If you purchased the `Fanatec DD Mount', please see page 16. Normal assembly continues on the next page. E7 E5 E3 E1 E4 1144 | 27 Front Mount Front Mount Spacer M8 X 25 1X 4X 4X Continue on page 18. E2 E5 E7 1155 | 27 F1 CSL Spacer* Front Mount Bracket A Front Mount Bracket B Front Mount Spacer M8 X 25 2X 2X 2X 2X 8X 8X *Fanatec DD1/DD2 does NOT need the CSL Spacer. F1 F3 F6 F5 F4 F2 1166 | 27 Front Mount Spacer M6 X 20 4X 4X F4 F7 DD1/DD2 users, please use M8 X 25 (F6) bolts. Continue on page 18. 1177 | 27 Cap-Washer M8 X 25 M8 Washer M8 Slot-Nut M8 (DIN 988) 4X 4X 4X 4X E12 E8 E9 E7 Part numbers for Fanatec DD Mount differ. 1188 | 27 650MM Profile 80X40 Side Mount End-Cap Bracket M8 X 25 Washer M8 Slot-Nut M8 B20 1X 1X 1X 2X 2X 2X B1 B12 B19 B14 B9 1199 | 27 320MM Profile 80X40 Side Mount Side Mount M8 X 25 End-Cap Angled Bracket Sandwich Plate M8 X 20 Washer M8 Slot-Nut M8 1X 1X 1X 1X 2X 2X 2X 2X B6 B13 B12 B2 B20 B16 B19 B14 2200 | 27 Cap-Washer M8 X 25 M8 Washer M8 Slot-Nut M8 (DIN 988) 2X 2X 2X 4X B20 B17 B18 B14 2211 | 27 M8 X 25 Washer M8 4X 4X B19 B14 2222 | 27 BOX A - PROF 56A PROFILE KIT # Part A1 160X40 UL Length=1350mm A2 160X40 UL Length=500mm A3 160X40 UL Length=490mm A4 120X40 Length=850mm A5 40X40 Length=500mm BOX B - BASE PACK 56 PROFILE KIT # Part B1 80X40 Length=650mm B2 80X40 Length=320mm HARDWARE KIT B3 Corner bracket 160x40 B4 Profile 160x40 end-cap B5 Profile 120x40 end-cap angled B6 Profile 80x40 end-cap angled B7 Profile 80x40 end-cap B8 Profile 40x40 end-cap B9 Upright sandwich plate LEFT B10 Upright sandwich plate RIGHT B11 Side mount sandwich plate B12 Side mount bracket B13 Bolt M8 X 40 DIN 912 B14 Bolt M8 X 25 DIN 912 B15 Bolt M8 X 20 DIN 912 B16 Bolt M8 X 20 DIN 7991 QTY Note 2 Machined. 1 Crossbeam. 1 Rear. 2 Uprights, angled. 2 Machined. QTY Note 1 Side mount. 1 Angled. 2 2 4 1 1 4 1 1 1 2 8 18 8 10 Countersunk. B17 Cap-Washer M8 10 B18 Washer M8 DIN 988 18 B19 Washer M8 DIN 125-A 8 B20 Slot-Nut M8 28 HARDWARE KIT - ADJUSTABLE FEET B21 Foot support plate 4 B22 Foot 4 B23 Bolt M8 X 25 DIN 912 8 B24 Washer M16 DIN 125-A 8 B25 Nut M16 8 B26 Slot-Nut M8 8 Small. Threaded ball-joint rod fitted. Pre-installed. Pre-installed. BOX C - Pedal Deck PROFILE KIT # Part QTY Note C1 160X40 Length=450mm 1 C2 80X40 Length=450mm 1 HARDWARE KIT C3 Pedal deck bracket 2 C4 Bolt M8 X 40 DIN 912 6 C5 Bolt M8 X 30 DIN 912 8 C6 Bolt M6 X 16 DIN 912 12 Extra. C7 Bolt M5 X 16 DIN 912 12 Extra. C8 Cap-Washer M8 14 C9 Washer M8 DIN 988 14 Small. C10 Slot-Nut M8 6 C11 Slot-Nut M6 12 Extra. C12 Slot-Nut M5 12 Extra. Disclaimer: for some entries on this page, we supply more than required as spare materials. Don't worry if you have some leftovers, this is intentional. 2233 | 27 BOX D - Wheel Deck (optional purchase) HARDWARE KIT # Part QTY Note D1 Wheel deck 1 D2 Bolt M8 X 50 DIN 912 2 D3 Bolt M8 X 20 DIN 912 2 D4 Washer M8 DIN 125-A 4 D5 Slot-Nut M8 4 BOX E - Front Mount (optional purchase) PROFILE KIT # Part QTY Note E1 120X40 UL Length=192mm 2 HARDWARE KIT E2 Front mount 1 E3 Front mount bracket A 2 E4 Front mount bracket B 2 E5 Front mount spacer 12 E6 Bolt M8 X 40 DIN 912 4 Extra. E7 Bolt M8 X 25 DIN 912 16 E8 Cap-Washer M8 4 E9 Washer M8 DIN 988 4 Small. E10 Washer M8 DIN 125-A 4 Extra. E11 Lock-Nut M8 4 Extra. E12 Slot-Nut M8 4 BOX F - Fanatec DD Mount (optional purchase) PROFILE KIT # Part QTY Note F1 120X40 UL Length=176mm 2 HARDWARE KIT F2 Front mount bracket A 2 F3 Front mount bracket B 2 F4 Front mount spacer 12 F5 CSL spacer 2 Only for CSL/GT DD. F6 Bolt M8 X 25 DIN 912 12+4 Also used to mount DD1/DD2. F7 Bolt M6 X 20 DIN 7380-2 4 F8 Cap-Washer M8 4 F9 Washer M8 DIN 988 4 Small. F10 Slot-Nut M8 4 Disclaimer: for some entries on this page, we supply more than required as spare materials. Don't worry if you have some leftovers, this is intentional. 2244 | 27 Please refer to the distance between the seat profiles to prepare for installing the seat. These should be close enough to save you some time and trouble! Sim-Lab Speed 1 380MM or 15" Sim-Lab Speed 3 370MM or 14.6" Sparco Rev 370MM or 14.6" SEAT COMPATIBILITY Sim-Lab Speed 1 XXL 440MM or 17.3" Sparco Circuit II Sparco Grid 400MM or 15.7" Sparco R100 305MM or 12" 2255 | 27 Accuforce 1/2 Asetek Forte/Invicta/Prima Fanatec WHEEL DECK COMPATIBILITY HRS/Sim-Lab Servo Mount Logitech (only Logitech G Pro uses 3 mounting holes) MOZA Simagic Thrustmaster Thrustmaster T818 2266 | 27 If you still have some questions regarding assembly of this product or about the manual itself, please refer to our support department. They can be reached at support@sim-lab.eu Alternatively, we now have a Discord server where there are quite some experienced Sim-Lab customers hanging out. They might just help you along if you ask them nicely ;) www.sim-lab.eu/discord If you feel like printing this manual, please consider the environment before doing so. For the best results, make sure you print at 100% scale without borders. Product page on the Sim-Lab website: 2277 | 27