Regulations Certificates | HP® United KingdomEnvironment | Poly, formerly Plantronics & Polycom
support.polycom.com/
Instructions for poly models including: P030, M72-P030, M72P030, TC10 Intuitive Touch Interface, TC10, Intuitive Touch Interface, Touch Interface, Interface
HP Inc. P030 M72-P030 M72P030 p030
File Info : application/pdf, 7 Pages, 388.92KB
DocumentDocumentSAFETY AND REGULATORY NOTICES September 2022 | 3725-37724-001A Poly TC10 This document covers Poly TC10 (Models P030 and P030NR). Service Agreements Please contact your Poly Authorized Reseller for information about service agreements applicable to your product. Safety, Compliance, and Disposal Information This equipment is intended for indoor use only. This equipment is not intended to be directly connected to outdoor cables. Do not spray liquids directly onto the system when cleaning. Always apply the liquid first to a static- free cloth. Do not immerse the system in any liquids or place any liquids on it. Do not disassemble this system. To reduce the risk of shock and to maintain the warranty on the system, a qualified technician must perform service or repair work. There are no user serviceable parts inside this product. This equipment is not intended to be operated by children. Users must not service any parts in compartments that require a tool to access. This equipment should be used only on even surfaces. Keep ventilation openings free from any obstructions. The ambient operating temperature rating of this equipment is 0-40°C and should not be exceeded. In order to remove all power from this unit, disconnect all power cables, including any USB or Power over Ethernet (PoE) cables. If the product is powered using PoE, you must use an appropriately rated and approved networking device compliant with IEEE 802.3af, or the power injector identified for use with this product. Operating Ambient Temperature Operating temperature: +32 to 104°F (0 to +40°C) Relative humidity: 15% to 80%, non-condensing Storage temperature: -4 to 140°F (-20 to +60°C) 1 Safety and Regulatory Notices | Poly TC10 Installation Instructions Installation must be performed in accordance with all relevant national wiring rules. L'Installation doit être exécutée conformément à tous les règlements nationaux applicable au filage électrique. When using Power over Ethernet (PoE), the equipment is to be connected only to PoE networks without connections to the outside plant. Lorsque vous utilisez une alimentation électrique par cable ethernet (PoE - Power over Ethernet), l'équipement doit être connecté uniquement aux réseaux PoE sans connexions vers l'extérieur de l'usine. USA Part 15 FCC Rules This device is compliant with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interferences received, including interference that may cause undesired operation. In accordance with part 15 of the FCC rules, the user is cautioned that any changes or modifications not expressly approved by Poly could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Responsible Party issuing FCC Supplier's Declaration of Conformity Polycom, Inc. 6001 America Center Drive San Jose, CA 95002 USA TypeApproval@poly.com. 2 Safety and Regulatory Notices | Poly TC10 Radiation Exposure Statement The antenna used for this transmitter must be installed to provide a separation distance of at least 20 centimeters from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This device with its antenna complies with FCC's RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance, this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Canada Industry Canada Statement This device complies with RSS247 of the Industry Canada rules and also with ISED's license-exempt RSS regulations. Operation is subject to the two following conditions: (1) This device does not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d' ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. This device for operation in band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. Cet appareil destiné à fonctionner dans la bande 5150-5250 MHz est uniquement destiné à une utilisation en intérieur afin de réduire le potentiel d'interférences nuisibles aux systèmes satellites mobiles cocanaux. This Class [A] digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada. Certification Number IC: 1849C-P030 Radiation Exposure Statement This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20 cm between the radiator and your body. 3 Safety and Regulatory Notices | Poly TC10 Déclaration d'exposition aux radiations Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de 20 cm entre le radiateur et votre corps. This Class [A] digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada. FCC and Industry Canada Example Label See an example of the Poly TC10 regulatory label below. FCC ID: M72-P030 IC: 1849C-P030 EEA CE Mark P030 is marked with the CE mark. This mark indicates compliance with EU Radio Equipment Directive (RED) 2014/53/EU, RoHS Directive 2011/65/EU, and Commission Regulation 278/2009. P030NR is marked with the CE mark. This indicates compliance with the EU EMC Directive (EMCD) 2014/30/EU, Low Voltage Directive (LVD) 2014/35/EU, RoHS Directive 2011/65/EU and Commission Regulation 278/2009. A full copy of the Declaration of Conformity for each model can be obtained at www.poly.com/conformity. Poly Studio TC10 Radio Operating Frequency The frequency ranges in the following table apply to Poly Studio TC10 (P030) Frequency Range 2.400Ghz 2.484Ghz 5.180Ghz 5.825 GHz Maximum Transmit Power +14.2 dBm EIRP +14.4 dBm EIRP 4 Safety and Regulatory Notices | Poly TC10 Japan Model P030 is only approved to transmit indoors within the W52 and W53 bands for Japan: W52(5180MHz / 5200MHz / 5220MHz / 5240MHz) W53(5260MHz / 5280MHz / 5300MHz / 5320MHz) VCCI A Statement This product can't be connected directly to the telecommunications circuits (or public wireless LANs) of any telecommunications carriers (e.g., mobile communications carriers, fixed communication carriers, or internet providers). To connect this product to the Internet, be sure to connect it via a router. Restriction of Hazardous Substances Directive (RoHS) All Poly products comply with the requirements of the EU RoHS Directive. Statements of compliance can be obtained by contacting typeapproval@poly.com. Environmental For the latest environmental information including Networked Standby Efficiency, battery replacement, handling, and disposal, take back, RoHS, and Reach, please visit https://www.poly.com/us/en/company/corporate-responsibility/environment. End of Life Products Poly encourages you to recycle your end-of-life Poly products in an environmentally considerate way. We recognize our Extended Producer Responsibility (EPR), in accordance with the requirements of the European Waste Electronic and Electrical Equipment (WEEE) Directive 2012/19/EU. All Poly products are marked with the crossed wheelie bin symbol shown below. Products that carry this symbol should be not be disposed of in the household or general waste stream. Further recycling information and detail of the options open to you, including our voluntary free global recycling service to ISO 14001 standard can be found at: https://www.poly.com/WEEE. The Poly Global Producer Responsibility Statement can be found in the Environment section of the Poly.com website. 5 Safety and Regulatory Notices | Poly TC10 Poly Take Back In addition to any mandated take back requirement, Poly offers free recycling of its branded products to business users. Detailed information is available at www.poly.com/us/en/company/corporateresponsibility/environment. 6 Safety and Regulatory Notices | Poly TC10 Getting Help and Copyright Information GETTING HELP For more information about installing, configuring, and administering Poly/Polycom products or services, go to the Poly Online Support Center. Poly 345 Encinal Street Santa Cruz, California 95060 © 2022 Poly. All trademarks are the property of their respective owners. 7