ORION EFFECTS LIGHTING

Important Safety Instructions

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER ON THIS LIGHT. THERE ARE NO USER-SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO A QUALIFIED TECHNICIAN.

NEVER look directly at the laser emitter as serious eye injury can occur. [Laser Emission Symbol]

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of "dangerous" voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to humans. Users should exhibit extra safety when this symbol appears in this instruction manual and follow all precautions as they are stated.

1. Read these instructions thoroughly before using this item. Heed all warnings. Follow all instructions.
2. Disconnect from the power source before servicing.
3. REPLACE FUSE WITH SAME TYPE AND RATING.
4. This product is for indoor use only! To prevent fire or electric shock, do not expose this equipment to rain or moisture. Do not store or operate this product near any liquids.
5. Do not store or operate this product near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
6. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a round grounding prong. The wide blade or third prong is provided for your safety. If the provided plug does not fit your outlet, consult an electrician for the replacement of the obsolete outlet.
7. Protect all wires connected to this unit from being walked on or pinched, particularly plugs and the point where they exit from the unit. When removing the cord from the power outlet, remove it by holding the plug not by pulling the cord.
8. Unplug the unit during lightning storms or when unused for long periods of time.
9. Allow the unit to cool down after 1 or 2 hours of continuous operation to prevent heat stress damage.
10. When wiring this unit and all other equipment used in connection to this unit make sure that all of your equipment is turned OFF.
11. Make sure the distance between the fixture and the lighted object is not less than 0.5 meters. Keep combustible and/or explosive materials away from this unit. Do not block the ventilation slots.
12. In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please return the unit to the nearest authorized technical assistance center.
13. The unit should never be connected to any kind of external AC dimmer. Operate only at intended voltage.
14. Make sure the power cord is never pinched or damaged.
15. Never disconnect the power cord by pulling or tugging on the cord.
16. Never carry the fixture directly from the cord. Always use the hanging/mounting bracket.
17. Before placing, installing, rigging, or suspending any product, inspect all hardware, suspension, cabinets, transducers, brackets and associated equipment for damage. Any missing, corroded, deformed, or non-load rated component could significantly reduce the strength of the installation, placement or array. Any such condition severely reduces the safety of the installation and should be immediately corrected. Use only hardware which is rated for the loading conditions of the installation and any possible short-term, unexpected overloading. Never exceed the rating of the hardware or equipment.
18. ALWAYS use a safety chain or cable between the unit and overhead suspension truss to ensure safety to persons.
19. Consult a licensed, Professional Engineer regarding physical equipment installation. Ensure that all local, state and national regulations regarding the safety and operation of equipment are understood and adhered to.
20. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Unpacking

Thank you for choosing our LED Flat Par Can (ORCAN4). For your own safety, please read this manual before installing the device. This manual covers the important information on installation and applications. Please install and operate the fixture with the following instructions.

The ORCAN4 uses 18 x 10W RGBWA + UV 6-in-1 LEDs, known for their long life, low power consumption, high brightness, and excellent color reproduction.

The ORCAN4 offers multiple control modes including automatic, manual, audio chase, and DMX. It is suitable for various scenarios such as stage lighting, theatre lighting, or any application requiring lighting.

The manual also includes a French version: "Manuel du Propriétaire".

Features & Specifications

Features

• Multi-Colour, Multi-Effect LED Par Can
• 18 x 6-in-1 RGBWA+UV LEDs
• Solid Aluminum Die-Cast Housing
• High Lumens (Brightness), Low Heat, Lower Power Consumption
• Multiple Control Modes: Automatic, Manual, Audio Chase, DMX
• Multiple DMX Modes
• Integrated Microphone for Audio Chase
• Includes Combination Mounting Bracket / Support Stand
• DMX in and out

Specifications

Operation Instructions

1. Do not turn on the device if it has been through severe temperature changes, especially after transportation. Operate at a stable temperature, avoiding drastic temperature changes to help avoid damage to the LEDs due to these environmental changes.
2. Avoid excessive shock or vibration of this device during transportation or when being moved.
3. Do not handle the light by the head only to prevent damage to the mechanical parts.
4. Do not expose the device to excessive heat, moisture, or dusty environments, especially during installation. Also, to avoid electric shock, do not run power lines across the floor.
5. Make sure the installation location is safe and in good condition before installing the device.
6. Ensure the safety chain is secured properly and check that screws are fastened properly.
7. Make sure the lenses are in good condition; it is recommended to replace any lens if there is any damage or scratches.
8. Make sure the device is operated by qualified personnel who know how to operate the device.
9. It is recommended to keep the original packaging.
10. Do not attempt to change or modify the device without instruction from the manufacturer, a qualified technician, or an authorized service agent.
11. Warranty is void if there are any malfunctions due to not following the owner's manual instructions or if operated when not in fully working condition (e.g., short circuit, electronic shock, broken lamp).

Menu Operations

Use the buttons on the unit to navigate the menu:

• Press "MENU" to select a function.
• Press "UP" or "DOWN" buttons to modify values.
• Press "ENTER" to confirm and save settings.

Detailed descriptions of menu functions are available within the manual.

DMX Control

DMX 10-Channel Control

DMX 6-Channel Control

Mounting

Important Safety Notes

• ALWAYS mount the light to a secure approved truss with sufficient load bearing capability to ensure a safe installation.
• ALWAYS use a galvanized steel wire as a secondary safeguard to prevent injury to property or persons in case the primary mounting mechanism fails. 12 gauge stranded steel utility wire will serve as an adequate safety cable for ORION products lights weighing less than 12 kg / 25 lbs.
• This secondary safety attachment must not interfere with positioning of the light.
• ALWAYS ensure C-clamps are fully tightened with thread-lock adhesive and properly orient the C-clamps for maximum security.
• ALWAYS perform periodic safety inspections to ensure the installation is safe and secure.
• Improper installation can result in bodily injury or death. If you are not qualified to attempt the installation, get help from a professional structural rigger.

ORION LIGHTING PRODUCTS MOUNTING EXAMPLE

Maintenance and Cleaning

Points to consider during inspection:

• There must not be any deformations on the housing (ceiling, suspension, trussing).
• The electric power supply cables must not show any damage, material fatigue, or sediments.

Further instructions, depending on the installation area and usage, must be adhered to by a skilled installer, and any safety concerns must be addressed.

CAUTION! Disconnect from mains before starting maintenance operation.

To keep the device in good condition and extend its lifetime, regular cleaning is recommended:

• Clean the lenses each week to avoid dust accumulation affecting the light output.
• Clean the device frequently using a moist, lint-free cloth. Never use alcohol or solvents.

If spare parts are needed, order genuine parts from your local dealer.

Warranty

Orion Lighting - One (1) Year Manufacturer's Defect One Year Limited Warranty: If this product fails within one year of the original purchase date due to a manufacturing defect, return the product to your Orion dealer with the original proof of purchase for free repair. This warranty excludes damage considered by the vendor to be the result of improper installation, normal wear, abuse, or shipping damage. See your Orion dealer for details. Warranty valid in Canada and the United States. Other territories may vary.

Orion Lighting - Un (1) An de Défaut de Fabrication Garantie limitée d'un an: Si ce produit tombe en panne dans l'année suivant la date d'achat d'origine en raison d'un défaut de fabrication, renvoyez simplement le produit à votre revendeur Orion avec la preuve d'achat originale et il sera réparé gratuitement. Cette garantie exclut les dommages considérés par le vendeur comme le résultat d'une mauvaise installation, d'une usure normale, d'un abus ou de dommages liés à l'expédition. Consultez votre revendeur Orion pour plus de détails. Garantie valide au Canada et aux États-Unis. D'autres territoires peuvent varier.

Distributors

Distributed in US by: Yorkville Sound, 4625 Witmer Industrial Estate, Niagara Falls, New York 14305

Distributed in Canada by: Yorkville Sound, 550 Granite Court, Pickering, Ontario L1W 3Y8