User Guide for Fiilex models including: 031725A, V3 COLOR Viewing Lamp, V3, COLOR Viewing Lamp, Viewing Lamp, Lamp
V3 User Guide Safety Instructions · DO NOT obstruct the fixture's air vents. · DO NOT install the light fixture in damp locations. · DO NOT disassemble the light fixture. This will void the warranty. · DO NOT look into the light source. Be cautious of the high-intensity beam. · Use a safety cable (not included) when rigging the light fixture overhead. · Shields and lenses shall be changed if they have become visibly damaged. · If damaged, the luminaire must be repaired or replaced before further use. · Only use Fiilex-approved power supply and accessories. Failure to do so may damage the fixture and will void the fixture's warranty. Parts Diagram 14 17 16 15 1 6 7 10 2 11 3 4 5 8 9 12 13 18 1. Vent Holes 10. OLED Display 2. Foam Rubber Bumper 11. Menu Knob 3. T Handle 12. DMX Output (TRRS) 4. Accessory Locking Magnet 13. DC Input Port (14-30V) 5. Accessory Locking Pin 14. Power Cable 6. Ball Joint Handle 15. Clamp 7. INT Knob 16. Rotation Locking Knob 8. USB Type-C Port 17. Adjustable Arm (For updating firmware/RPU) 9. On / Off Button 18. DC Power Plug 1689 Regatta Blvd. Richmond, CA 94804 | (510) 620-5155 | fiilex@fiilex.com 031725A www.fiilex.com 1 Twist the clamp handle (1) clockwise to loosen the clamp. 4 2 Insert the clamp at the side of desired surface. Twist the clamp handle (2) counter-clockwise to mount the fixture to the side of table. 3 5 360° Rotate the adjustable arm (3) to desired location and twist the rotation locking knob (4) to secure the position of the lamp. Accessories Twist the ball joint handle (5) counter-clockwise to release V3 head. After adjusting the V3 head to the desired angle, reverse the process to secure. RPU FLXRPU P3 Dome Diffuser 1-Stop FLXP3CLR-DOME1S P3 Fresnel Lens 20deg FLXP3LR-FRNL20 1689 Regatta Blvd. Richmond, CA 94804 | (510) 620-5155 | fiilex@fiilex.com www.fiilex.com Control Panel Guide Control panel overview OLED Panel INT Knob REMOTE FW Port ON/OFF Button Menu Knob DMX Input Port DC 14-30V Intensity Controls * Use the INT Knob to modify brightness in any mode Menu Knob Controls * Use the menu knob to adjust all other parameters, navigate the menu, and change modes. INT Twist Adjust fixture output Menu 1x Press Enter edit mode/ Press again to Confirm Select / Change Mode 1) Once the fixture is powered on, twist menu knob until menu appears, tap once. Menu Twist Select/ Adjust Menu 2x Press Enter Mode Selection and Advanced Setting 2) Twisting the menu knob will move through other settings that can be changed. 3) Press the menu button once while the Mode is on the screen. Two arrows will appear in the center of the screen at the top and bottom. Menu 1x Press 4) Twist the menu knob until the appropriate mode is selected, and press the menu knob to enter. *A Full list of available modes can be found on the webpage. Menu Twist CCT Mode Operation 1) The "INT" knob controls the overall fixture output. Menu Twist INT Twist 1689 Regatta Blvd. Richmond, CA 94804 | (510) 620-5155 | fiilex@fiilex.com www.fiilex.com 2) To make adjustments to the CCT, twist the menu knob until "CCT" is highlighted. Press the menu knob once. Two arrows will appear in the above and below the current CCT value. Twist the menu knob to make adjustments and press the menu knob to save. Menu Twist Menu 1x Press 3) To adjust the Green / Magenta shift, twist the menu knob until "GN" is highlighted. Press the menu knob once. Two arrows will appear above and below the current GN value. Twist the menu knob to make adjustments and press the menu knob to save. Menu Twist Menu Twist HSI Mode Operation 1) The "INT" knob controls the overall fixture output. Menu 1x Press Menu Twist INT Twist 2) To make adjustments to the HUE, twist the menu knob until "HUE" is highlighted. Press the menu knob once. Two arrows will appear above and below the current HUE value. Twist the menu knob to make adjustments and press the menu knob to save. Menu Twist Menu 1x Press 3) To adjust the Saturation shift, twist the menu knob until "SAT" is highlighted. Press the menu knob once. Two arrows will appear above and below the current SAT value. Twist the menu knob to make adjustments and press the menu knob to save. Menu Twist Menu 1x Press Menu Twist Menu Twist Menu 1x Press Menu 1x Press Menu 1x Press Menu 1x Press RGBW Mode Operation 1) The "INT" knob controls the overall fixture output. INT Twist 2) To make adjustments to the Red shift, twist the menu knob until "R" is highlighted. Menu Twist 3) Press the menu knob once. Two arrows will appear above and below the current red value. Twist the menu knob to make adjustments and press the menu knob to save. Menu 1x Press 4) Repeat process in order to change the rest of the settings. Menu Twist *For advanced mode control and more options, visit the main Fiilex webpage. Menu 1x Press 1689 Regatta Blvd. Richmond, CA 94804 | (510) 620-5155 | fiilex@fiilex.com www.fiilex.comAdobe PDF library 17.00 Adobe Illustrator 29.2 (Macintosh)