Automotive OEM integration | CRUX Interfacing Solutions
User Manual for CRUX models including: SWRNS-63A, SWRNS-63A Wiring Interface, Wiring Interface, Interface
CRUX SWRNS-63A Wiring Interface Connect a new car stereo and retain the steering wheel audio controls and other factory features in select 2013-19 Nissan vehicles at Crutchfield
File Info : application/pdf, 3 Pages, 4.87MB
DocumentDocumentINTERFACING SOLUTIONS R + RADIO REPLACEMENT SWC RETENTION PRODUCT FEATURES: SWRN S-63A Radio Replacement with Steering Wheel Control Retention for Select 2012-2019 Nissan Vehicles - Pre-programmed to retain factory Medium Speed CAN-Data Bus Steering Wheel Controls. - Includes antenna adapter. PARTS INCLUDED: SWRNS-63A MODULE SWRNS-63A Harness Antenna Adapter INSTALLATION DIAGRAM FOR NON-AMPLIFIED VEHICLES: SWC Cables +12V Constant Yellow +12V ACC Red Ground Black Illumination (+) Orange Illumination (-) Orange/White Right Front (+) Gray Right Front (-) Gray/Black Left Front (+) White Left Front (-) White/Black Right Rear (+) Violet Right Rear (-) Violet/Black Left Rear (+) Green Left Rear (-) Green/Black VSS (Vehicle Speed Signal) Brown/White Chassis Ground Black (with Ring Terminal) 16 PIN TO FACTORY 20 PIN HARNESS AFTERMARKET RADIO 12-Pin Black Connector BLUE/ Power Antenna ON 1 2 3 3.5MM SWC CABLES (Option A or B) Use the proper 3.5MM to 4-Pin cable for your radio. Plug in the selected 3.5MM SWC cable to the 4-pin port on the module. See "DIP SWITCH SETTINGS" section. 4-Pin Connector Option B: To aftermarket radio SWC wire or 3.5mm port Cap or insulate if not being used Insulate with tape if not being used BLUE / YELLOW Option A: 1 of 2 Crux Interfacing Solutions · Chatsworth, CA 91311 phone: (818) 609-9299 · fax: (818) 996-8188 · www.cruxinterfacing.com rev.230122 INTERFACING SOLUTIONS R + RADIO REPLACEMENT SWC RETENTION SWRN S-63A Radio Replacement with Steering Wheel Control Retention for Select 2012-2019 Nissan Vehicles DIP SWITCH SETTINGS: AFTERMARKET RADIO DIP SWITCH SETTINGS: RADIO BRAND: DIP#: Atoto, Dual, Fahrenheit, Jensen, Nakamichi, Pioneer, Power Acoustik, Soundstream Alpine Clarion, Stinger Kenwood JVC Boss, Old Sony New Sony (with CarPlay) 1 2 3 OFF ON ON OFF ON ON OFF ON ON OFF OFF OFF ON ON OFF ON ON ON ON OFF ON ON OFF OFF OFF ON OFF SWC MODULE DIP SWITCH ON 1 2 3 NOTE: check the aftermarket radio's manual to see if the SWC buttons need to be programmed. 4-PIN SWC CABLE OPTION B is used for ATOTO, BLAUPUNKT, BOSS, DUAL, FARENHEIT, JENSEN, POWER ACOUSTIK, NOTE: Cap or insulate the 3.5mm plug or Blue/Yellow wire if not being used. connect the SWC wires as follows: Note that there are some radios that only have SWC1 and SWC2, in this case "shield" does not need to be connected. VEHICLE APPLICATIONS: RED to SWC Key 1 WHITE to SWC Key 2 SHIELD to SWC Ground NISSAN 2013 - 2017 Altima Base Radio 2012 - 2019 Versa NOTE: Some SWC functions might not be retained for the following radio series: Planet Audio P9900CPA, Jensen CAR 710, Atoto F7, and similar radios of these brands. 2 of 2 Crux Interfacing Solutions · Chatsworth, CA 91311 phone: (818) 609-9299 · fax: (818) 996-8188 · www.cruxinterfacing.com rev.230122 DIP switch settings for Pioneer receivers: ~/:· -~.c! :· !. :=~~==~= Location of the switch may vary on the Interface (Comer or Middle). Please note that interfaces with DIP at the end of the LOT# are installed with the switch. · Set DIP switch to "3V3" position for support of NEW generation Pioneer steering wheel button control. · Set DIP switch to "5V" position for support of OLD generation Pioneer steering wheel button control.