User Guide for Eleven Engineering Incorporated models including: PL5572-R2003 Rush Receiver for Analog Audio, PL5572-R2003, Rush Receiver for Analog Audio, Receiver for Analog Audio, Analog Audio
Eleven Engineering Incorporated PL5572 OP5PL5572 OP5PL5572 pl5572
File Info : application/pdf, 6 Pages, 739.30KB
DocumentDocumentRush User's Guide Rush Receiver for analog audio Model: PL5572-R2003 PL5572-R2003 Works With Requirements Notes Devices with a 3.5 mm analog input (sometimes referred to an AUX IN) The device must support analog audio in See the "SKAA Receivers Users Guide" on pages 3 and 4 of this document for instructions on how to use the Bond Button. Rush is capable of receiving both SKAA (36ms latency) and SKAA Pro (19ms Latency) signal from SKAA transmitters. Adjust local volume by using the + and - buttons shown below LOCAL VOLUME UP LOCAL VOLUME DOWN BOND BUTTON Rush User's Guide PL5572-R2003 Rush User's Guide SKAA® RECEIVER USER'S GUIDE PL5572-R2003 Each SKAA receiver uses a Green List to remember your favourite audio sources (SKAA transmitters). A Green glowing Indicator on your receiver means you are listening to a favourite, or hunting for one. You can also explore to find new transmitters--an Amber Indicator means you are exploring for transmitters which are not on your Green List. The Bond Button on your receiver lets you select which audio source (SKAA transmitter) you're listening to. Essentials Button Hold a few seconds Command Add / Delete Manually add / delete the current transmitter to / from your Green List 1 Click 2 Clicks Auto Add SKAA will automatically add the current Amber transmitter to your Green List if you listen to it for 30 minutes Green Mode Rotate through your list of favourite transmitters (Green List) -- when a favourite transmitter is found, the search stops and audio plays from that transmitter Amber Mode Explore for new, unknown transmitters (ones which are not already on your Green List) Indicator to = Added (flash) = Deleted to = Added (dim) = Hunting (flash) = Next one (bright) = Bonded (dim) = Hunting (bright) = Bonded More Commands Button Command Indicator 3 Clicks Mute do again to Unmute; any Click command , or = Muted will first Unmute and then do its function (slow flash) 4 Clicks Red Mode If you have 2 or more transmitters on your Green List, power on just the one you want to hear and it plays automatically. (dim) = Hunting (bright) = Bonded 6 Clicks Factory Reset Clear Green List. Start Over! (flash) = Reset Done Hold during power on Make a Cluster of Receivers: 1. Power off all transmitters and receivers 2. Power on the Master receiver while holding down its Bond Button--hold the button down until the Indicator begins to flash Red 3. With the remaining receivers within 3 meters of the Master receiver, power on the first one, wait for its Indicator to flash Red and then power on the second one; continue until all of them are powered on 4. Once all of the Indicators stop flashing (turn solid Red), power off all of the receivers (flash) = Receiver has entered `Cluster Up' mode (bright) = The Cluster has been successfully made Rush User's Guide Question QUESTIONS AND ANSWERS Answer PL5572-R2003 How does the Green List work? You can store up to 10 SKAA transmitters on your Green List. These are your "favourite" audio sources. Every time you add a transmitter, it is assigned the first open spot on the Green List. When you single click the Bond Button, the receiver hunts through the Green List much like a car radio hunts for radio stations when you press seek. If the Indicator is dim Green and flashes every few seconds, this tells you the receiver is hunting through the Green List. Say you have 5 transmitters on your Green List; your receiver will hunt through the list one by one: 1, 2, 3, 4, 5 and then back to 1 and so on. The dim Green Indicator flashes every time the receiver moves to the next spot on the list. This hunting goes on for up to 1 minute. If your receiver doesn't find any of your favourite transmitters, it stops hunting and just waits for the last bonded favourite. If your receiver does find one of your favourite transmitters, the hunting stops, the Indicator turns bright green, and your receiver starts playing audio from that favourite. A dim Green Indicator that is NOT flashing means the receiver is just sitting on one spot, waiting for a specific favourite transmitter to show up. How do I bond with a specific Green transmitter? Play audio from your source device and ensure it has a SKAA transmitter connected. Click the Bond Button on your receiver. The receiver hunts through the Green List, flashing the Indicator as it goes. Once your receiver finds one of your favourite transmitters, it bonds to it and plays audio from that transmitter. If that isn't the transmitter you wanted, click the Bond Button once more. Repeat until your receiver bonds with the transmitter you want and you're hearing the correct audio playing. How do I select transmitters if I can't reach my Bond Button? Say you want to put your receiver on a high shelf where you can't reach the Bond Button easily. First, set up your Green List: add all of the transmitters you'll want to use. Then 4-click the Bond Button to enter Red Mode. Now put the receiver up on the high shelf. Power on just one of your transmitters and power off all others. The receiver automatically bonds to the transmitter that's on. How do I delete a transmitter from my Green List? Factory Reset (6 Clicks of the Bond Button) clears the Green List and lets you start over from scratch. If however, you'd like to delete just one transmitter from your Green List, first bond your receiver to the transmitter you wish to delete. See the section above: How do I bond with a specific Green transmitter?. Once you are bonded to it, hold down the Bond Button for a few seconds until you see the Indicator flash Red --this Red flash means the transmitter has been deleted. What is a Cluster? Clusters are an optional convenience for "power users". A Cluster is several SKAA receivers behaving as one product. A left & right speaker pair, for example, or a sound bar and subwoofer. What is the Master In any Cluster, there is a single Master receiver, and all of the other receivers in the Cluster follow its receiver? behaviour. You can control the entire Cluster by operating the Bond Button of the Master. A receiver must have a physical Bond Button in order to become the Master. How do I Do the Make a Cluster of Receivers procedure once for each receiver, but omit Step 3. Do them one "uncluster" several at a time. This gives each of the receivers a functioning Bond Button, and each of them will receivers? thereafter operate independently. What are some tips for making Clusters? Each step in the Make a Cluster of Receivers procedure has a 10-second time limit. When you see the Master's Indicator start to flash Red, you have 10 seconds to power on the next receiver. When that receiver's Indicator starts to flash Red, you have 10 more seconds to power on the next one, and so on. Why does only one of my Bond Buttons work? When you make a Cluster from several receivers, the first one powered on in the Make a Cluster of Receivers procedure becomes the Master of the Cluster. Only the Master's Bond Button works because a Cluster uses just one Green List --the Master's Green List. The Bond Button of each of the other receivers will work only for the Mute / Unmute function (3-Click of the Bond Button). Can any group of No. The receivers must be members of the same product family. If they are not, the Make a Cluster receivers be made of Receivers procedure won't work. This is because only receivers which were designed to work into a Cluster? together (as a single product) can be made into a Cluster. Rush User's Guide PL5572-R2003 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Rush User's Guide PL5572-R2003 IC Warning This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device Le présent appareil est conforme aux CNR d' Industrie Canada applicables aux appareils radio exempts de licence. L' exploitation est autorisée aux deux conditions suivantes: (1) l' appareil ne doit pas produire de brouillage, et (2) l' utilisateur de l' appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d' en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme aux limites d'exposition au rayonnement ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps. This radio transmitter [IC:3534A-PL5572] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna Types Printed Inverted-F PCB Antenna Maximum gain (dBi) 3.29 Impedance 50macOS Version 12.7.2 (Build 21G1974) Quartz PDFContext Pages