larm.com
P65Warnings.ca.gov
SECO-LARM USA Inc
Instruction Manual for ENFORCER models including: SD-962AR-36G, SD-962BR-36G, SD-962AR-36G Grade 1 Rim-Type Exit Device, SD-962AR-36G, Grade 1 Rim-Type Exit Device, SD-962DR-36G
Rugged Grade 1 Rim-Type Exit Device, Push-to-Exit Bar - SECO-LARM USA Inc
Rugged Grade 1 Rim-Type Exit Device, Push-to-Exit Bar
File Info : application/pdf, 4 Pages, 898.62KB
DocumentDocumentSD-962AR-36G, SD-962BR-36G SD-962DR-36G Grade 1 Rim-Type Exit Device Manual Panic Hardware 51X4 Heavy-duty ANSI Grade 1 steel construction Allows exit from inside while locked from outside Reversible non-handed design For metal or wood doors up to 13/4" (44mm) thick Separate deadlocking latch prevents the use of credit cards or similar means to open the latch bolt Fits doors from 33" to 48" (84~122 cm) wide Hex-type 1/4-turn dogging lock allows the exit device to be unlocked for extended period of time Includes all needed hardware for typical installation Works with standard external door handle/lock devices (not included) BHMA 156.3 ENFORCER Grade 1 Rim-Type Exit Device Introduction: The ENFORCER Grade 1 Rim-Type Exit Device, when mounted on the inside of a door to block entry to a protected premises, securely locks the door from outside access while allowing users inside the protected premises to exit. The stainless steel enclosure protects the exit device from abuse, yet easily unlocks the door from the inside by users who require exit. It can be connected to an entry-type lever trim or to any physical locking device on the outside of the door in order to allow entry to authorized personnel. Specifications: Construction For doors Hand Latch bolt Dead latch Strike Spring Chassis Cover Rail assembly End cap Dogging Dimensions Weight ANSI Grade 1 steel 13/4" (44mm) thick, wood or metal Non-handed Stainless steel, 3/4" (19mm) throw Stainless steel 5/8" (16mm) throw For 5/8" (16mm) stop Stainless steel Plated steel Plated zinc cast Aluminum Plated zinc cast Hex-type dogging standard 33"x8"x23/16" (838x203x56 mm) 9-lb 12-oz (4.4kg) Parts List: 1x Grade 1 Rim-Type Exit Device 1x Manual 1x Mounting template 1x Strike 1x Hex key 1x End cap 1x End cap bracket Mounting hardware (see below) Screws Included: Mounting chassis to door: 4x 1/4"x3/4" machine screws 4x 1/4"x3/4" wood screws 4x sex bolts Connecting end cap to end cap bracket: 2x M4x6mm machine screws Mounting end cap bracket to door: 2x 1/4"x3/4" machine screws 2x 1/4"x3/4" wood screws Mounting strike to door: 2x 1/4"x3/4" machine screws 2x 1/4"x3/4" wood screws 1x #12x3/4" machine screw Dimensions: 23/16" (56mm) 213/16" (71mm) 21/4" (57mm) 8" (203mm) 2 33" (838mm) 23/8" (61mm) SECO-LARM U.S.A., Inc. Overview: ENFORCER Grade 1 Rim-Type Exit Device Strike Mechanism housing Chassis Push bar Chassis cover End cap End cap bracket Dogging device use hex key to lock in the open position so the door can be opened from outside the protected premises Sample Applications: Single Door Door Trim Exit device Double Door with Mullion Door Trim Door Trim Exit device Exit device 27/16" (62mm) Double Door without Mullion Mounting: Door Trim Exit device 215/16" (75mm) 27/16" (62mm) Door Trim Exit device Double-door strike (not included) Door Draw line here 40" (102cm) SECO-LARM U.S.A., Inc. Strike 3 ENFORCER Grade 1 Rim-Type Exit Device Final Installation: NOTE: Diagram shows 6 screws for mounting the chassis. Product only includes 4 screws. For best results, use 6 screws. 1. Mark the vertical center line of the exit bar by drawing a line across the door at 40" above the floor. See "Mounting" on page 3. 2. Fold the included template, and align the center lines on the template with the center line drawn on the door. Then mark the position of the mounting holes for the latch assembly. See "Mounting" on page 3. 3. Move the template against the door stop and then mark the mounting holes for the strike. 4. Drill the holes as marked on the door and the mullion. See "Mounting" on page 3. California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. WARNING: Incorrect mounting that leads to exposure or moisture inside the enclosure could damage the device and will void the warranty. LIMITED WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM's obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser's exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM's option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else. NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2021 SECO-LARM U.S.A., Inc. All rights reserved. SECO-LARM® U.S.A., Inc. 16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com PITSW6 Phone: (949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com MI_SD-962xR-36G_211116.docx 4 SECO-LARM U.S.A., Inc.