Video-Türsprechanlagen und mehr: Gebäudekommunikation | Merten
Lösungen für intelligente Gebäude | Merten
Installation Guide for RiTTO models including: RGE2057101 TwinBus IP REG Bus Filter, RGE2057101, TwinBus IP REG Bus Filter, REG Bus Filter, Bus Filter, Filter
Anleitungen & Dokumentationen | Merten
File Info : application/pdf, 2 Pages, 488.96KB
DocumentDocumenten TwinBus IP REG Bus Filter Installation Guide TM Device overview CLICK TH 35 (DIN EN 60715) RGE2057101 For your safety DANGER HAZARD OF ELECTRIC SHOCK, OR ARC FLASH Safe electrical installation must be carried out only by skilled professionals. Skilled professionals must prove profound knowledge in the following areas: · Connecting to installation networks · Connecting several electrical devices · Laying electric cables · Safety standards, local wiring rules and regula- tions Failure to follow these instructions will result in death or serious injury. About this document In this document you will find all information for safe installation. For further product information, follow the QR Code. https://www.merten.de/ profibereich/service/downloads. html Scope of supply REG Bus Filter, installation guide Introduction to the TwinBus IP REG Bus Filter The TwinBus IP REG Bus Filter (hereinafter referred to as the bus filter) is designed for isolating the power supply from the bus. A Port In A Bus +, In B Bus B LED green C Port Out A Bus +, Out B Bus D Disassembly clip The green LED indicates that the supply voltage from the REG power supply is present. The right place to install The bus filter is mounted on a TH 35/7.5 or TH 35/15 standard DIN rail. When choosing the installation location, the maximum cable length must be observed. The following table shows the maximum cable length between the bus filter and the system.components. Group 0.8 mm Cable Group 0.6 mm Cable Group 0.5 mm Cable REG power supply Door station Video indoor station < 1 m 80 m 80 m < 1 m 60 m 80 m < 1 m 50 m 50 m Group 0.8 mm cable: YR 2x0.8 mm, J-Y(ST)Y 2x2x0.8 mm, A-2Y(L)2Y 2x2x0.8 mm, CAT5e / CAT6 0.8 mm Group 0.6 mm cable: A-2Y(L)2Y 2x2x0.6 mm, J-Y(ST)Y 2x2x0.6 mm, CAT5e / CAT6 0.8 mm Group 0.5 mm cable: CAT5e / CAT6 0.5 mm When using a shielded cable, the shield must not be connected. Installation WARNING DANGER TO LIFE DUE TO ELECTRIC SHOCK · Only mount devices with basic insulation next to the device. Failure to comply with this instruction may result in death or serious injury. 1 Attach bus filter to DIN rail. Circuit diagram A B A B RGE2087... LN + Out In BA BA B A (1) RGE2057100 RGE2057101 B A RGE2098500 RGE20151xx B A RGE20152xx (1) Terminal strip Technical data Performance data Input voltage Current consumption Environmental conditions Ambient temperature Humidity (max) Dimensions and weight Dimension (W x H x D) Weight Space requirement on the DIN rail Connection terminal Clamping range (conductor diameter) Nominal torque Housing insulation Protection class SELV DC 24 V <0.05 A -10 °C ... 55 °C 96 % 17.8 x 99.3 x 66.1 mm 61.5 g 1 TE 4x 0.5 mm (AWG 24) solid 3x 0.6 mm (AWG 22) solid 2x 0.8 mm (AWG 20) solid Copper-clad aluminum conductors must not be used. 0.2 Nm Basic insulation to neighboring DIN rail devices The device complies with the IP30 protection class if it is installed in a distribution cabinet with at least IP30. WEEE Dispose of the device separately from household waste at an official collection point. Professional recycling protects people and the environment against potential negative effects. NNZ42648-02 04/22 Schneider Electric GmbH c/o Ritto Gothaer Straße 29, 40880 Ratingen Customer Service: Telephone: +49 211 7374 8008 www.ritto.de © 2022 Schneider Electric, all rights reserved NNZ42648-02 04/22