Ranqer Halo RGB Gaming Chair Assembly and Usage Instructions
This manual provides instructions for the assembly and use of the Ranqer Halo RGB gaming chair.
Important Safety Information
WARNING!
Read the entire manual carefully before installing and/or using this product. Follow the manual carefully and keep it for future reference. If the product is damaged or any parts are missing, please contact customer service immediately.
- Please check the chair's load capacity and make sure to not overload it to avoid injury and damage: max. 150KG and max. 1 person.
- Make sure the chair is on a flat surface.
- Do not stand on the chair.
- For indoor use only.
- Only qualified people can proceed with product maintenance. Do not attempt to repair if you are not qualified. Contact customer service for more information regarding repairs and warranty.
- Keep the product out of reach of children. More so during assembly as small pieces might cause choking hazards.
Important Note: Do not pull the adjustment handle before installation is complete.
Parts List
Please ensure the package contains the following items. If a part is missing, please contact customer service.
Components:
- (1) 1x Star Base
- (2) 5x Casters (Wheels)
- (3) 1x Gas Lift Cylinder
- (4) 1x Mechanism/Tilt Control
- (5) 1x Backrest Cushion
- (6) 1x Seat Cushion
- (7) 1x Armrests (Left & Right)
- (8) 1x Lumbar Support Cushion
- (9) 1x Headrest Pillow
- (10) 1x Accessory Kit (including screws and tools)
- (11) 1x Seat Tilt Mechanism
- (12) 1x Mounting Plate
- (13) 1x Allen Wrench
- (14) 1x Remote Control & Cable
- (15) 7x M8*25mm Screws
- (16) 8x M8*20mm Screws
- (17) 4x M5*8mm Screws
- (18) 4x Washers
- (19) 4x Lock Washers
Assembly Steps
Step 1: Assemble the Armrest and Tilt Control
Attach the armrests and the tilt control mechanism to the underside of the seat cushion using the provided screws (16, 18, 19).
Step 2: Attach Seat Mechanism to Seat
Secure the seat tilt mechanism (11) to the seat cushion (6) using screws (15).
Step 3: Attach Backrest to Seat
Connect the backrest (part of the main chair structure) to the seat mechanism using screws (17).
Step 4: Assemble the Base and Gas Lift
Insert the casters (2) into the star base (1). Place the gas lift cylinder (3) into the center of the star base.
Tip: Slide the wheel at a 45-degree angle to assemble it.
Step 5: Mount the Chair onto the Base
Carefully lift the assembled seat and backrest and place it onto the gas lift cylinder.
Step 6: Attach Headrest and Lumbar Support
Attach the headrest pillow (9) and lumbar support cushion (8) to the chair using the provided straps.
Step 7: Connect RGB Lighting (if applicable)
Connect the RGB lighting cable (14) to the appropriate port on the chair and plug it into a power source using the remote.
Usage Instructions
- Height Adjustment: Sit in the center of the chair when adjusting the height. Lift the lever gently to raise or lower the chair. Do not pull it roughly.
- Rocking Function: Pull out the handle under the seat to start rocking. Insert the handle to stop rocking.
- Rotation: The chair can rotate 360 degrees.
- Rocking Angle Adjustment: Adjust the rocking angle by turning the knob under the seat. Clockwise rotation adjusts the rocking angle from 0-10 degrees. Counterclockwise rotation adjusts the rocking angle from 10-30 degrees.
- Backrest Adjustment: Adjust the backrest angle by using the lever on the side of the seat. Be careful with your fingers when adjusting the backrest.
General Usage Tips:
- Move the product gently to avoid collision.
- Keep the chair out of direct sunlight.
- Ensure the center of gravity is on the base during use.
- Do not use the chair unless all bolts, screws, and knobs are tightened.
- Be careful, some parts are heavy and have sharp edges. Failure to follow these warnings may cause serious injury.
- Do not place any heavy objects on the chair or armrest.
- Do not use harsh cleaners on the chair.
- It is advised that users check and tighten screws every 6 months.
Frequently Asked Questions (FAQ)
- Missing Parts: If parts are missing, do not assemble further. Contact customer service for replacement parts.
- Defective Chair: If the chair has a defect, take pictures of the defective parts and send them to customer service via email for further instructions.
- Broken Chair: Do not attempt to repair a broken chair yourself. Contact customer service for repair or replacement options.
- Contacting Customer Service: Visit www.ranqer.com/contact to find customer service contact details for your country.
Importer Information
Importer: SB Supply Europe B.V.
Address: Parallelweg 9, 7141DL GROENLO, The Netherlands
Ranqer is a brand of Ranqer International B.V. registered in The Netherlands.
Made in PRC, Designed in Holland.