Handheld Two Way Radio Manufacturer / Walkie Talkie Supplier | Anytone
Instruction Manual for AnyTone models including: AT-D578UV PLUS, AT-D578UVIII PLUS, AT-D578UV PRO, AT-D578UVIII PRO, AT-D878UV PLUS, AT-D878UVII PLUS, AT-5555NII, AT-6666PRO, BT03 DT03 Desktop Microphone, BT03 DT03, Desktop Microphone, Microphone
Qixiang Electron Science& Technology Co., Ltd BT03 Microphone T4K-BT03 T4KBT03 bt03
File Info : application/pdf, 3 Pages, 860.55KB
DocumentDocumentDesktop Microphone Instruction Manual BT03 Bluetooth Version DT03-1 RJ45 Jack DT03-2 6pins Jack BT03 Wireless (with built-in BT and battery) DT03 wired (without built-in BT and battery) APPLICABLE MODELS AT-D578UV PLUS AT-D578UVIII PLUS With GPS and BT AT-D578UV PRO AT-D578UVIII PRO With GPS and BT AT-D878UV PLUS AT-D878UVII PLUS With GPS and BT AT-5555NII RJ45 Jack AT-6666PRO 6pin Jack BT03 DT03-1 DT03-2 wireless RJ45 Jack cable 6pin Jack cable 1. Getting Started(Bluetooth Desktop Microphone) MIC CHANNEL /VOLUME DOWN SPEAKER POWER/NRC SWITCH CHANNEL/VOLUME UP MONITOR CHARGING/UPDATING RESTART PTT 1 2. Charge The Battery(Only for BT03) (1)Connect the Bluetooth microphone and 5V/1A power supply via TYPE-C cable. (2)Insert the charging head into the AC socket. (3)Charging processing: the indicator light on. (4)When the charging indicator light off, indicating that the battery is fully charged. 3. Operation 3.1 Power On Press and hold the [NR PWR] button in the power-off state until the microphone prompts "Power on", then release the button to turn on the microphone. 3.2 Power off In standby mode, press and hold the [NR PWR] button until the microphone prompts "Power off", then release the button and the microphone will power off. 3.3 Bluetooth pairing(Only for BT03) In standby mode, press and hold the [CH-VOL-] button and the [CH+ VOL+] button at the same time until the microphone prompts "Bluetooth pairing", that is, enter the pairing state. In this state, the D578UV series radio also needs to enter the Bluetooth pairing state, when the screen displays "BT MIC HAND", the Bluetooth microphone will be detected, click to connect, and the microphone will prompt "Bluetooth connected", indicating that the Bluetooth pairing is successful and connected with the 578UV. Note: This function is invalid for Non-bluetooth version. 3.4 Adjust the volume In standby mode, press [CH-VOL-] to decrease the volume, press [CH+ VOL+] to increase the volume, and the microphone will prompt the adjusted volume level with a voice reminder every time the volume is adjusted. 2 3.5 Adjust the channel Press and hold the [CH+ VOL+] button until the microphone prompts "Channel up regulation" and then release the button, which means D578UV will increase one channel. 3.6 Noise reduction In standby mode, press the [NR PWR] button and the microphone will prompt "Noise reduction on" or "Noise reduction off" to turn on or off. Note: If the radio has NRC function and NRC is enabled on radio, DO NOT turn on NRC function on desk microphone again, otherwise it will affect the radio voice quality. 3.7 Low power(Only for BT03) When the Bluetooth dock prompts "Please charge", that is, the battery is about to run out, please charge it in time. When charging, the indicator on the far right of the seat is lit up, and the red LED indicator lights up. When the red light turns green, charging is complete. Note: When charging, please use a 5V/1A charger to charge the microphone. The charging cable adopts USB Type-C. 3.8 Call To speak, press and hold the PTT button (right side button of the base) until the red LED light in the middle of the seat is lit and then speak into the MIC. Release the PTT button and wait for the other person to answer. 3.9 Monitor(Only for BT03) In standby mode, press and hold the monitor button (the left button of the base) to enter the monitoring state. If the channel is analog, the microphone will emit noise. Note: This function is invalid for wired desktop microphone. 3.10 Restart If the equipment cannot be used properly due to improper use and cannot be shut down properly, you can use this key to force it to shut down and then restart it. 4. Technical Specifications BT version Protocol Transmit Distance BT03 wireless BT5.4 HFP AG; BLE 10 Meters Maximum Transmission Power MAX: 6dBm Sensitivity Audio performance Speaker Charge Battery capacity/Votage Dimension (H*W*D) Weight Working Temperature MIN: -91dBm SBC Decoding 2W/8R 5V Type C USB 1200mAh 3.7V 113x174x63mm 426g -20°C ~ 55°C Coil cable type Coil cable length Speaker Dimension (H*W*D) Weight Working Temperature DT03-1 DT03-2 RJ45 Jack cable 6pin Jack cable 50cm coiled (3m uncoil) 2W/8R 113x174x63mm 480g -20°C ~ 55°C 3 4 www.anytone.net A1.241218 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference including received interference that may cause undesired operation. The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user's authority to operate the equipment. Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules. We declare that the device is compliance with Radio Equipment Directive (RED) 2014/53/EU. The device in the environment with the temperature between 0-40 and operating under 2000m, otherwise, it may damage your device. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. A1.241218