User Manual for virtufit models including: VF06051-305, Jump Pro Deluxe Trampoline with Safety Net, VF06051-305 Jump Pro Deluxe Trampoline with Safety Net
Index of /wp-content/uploads/2022/03
VirtuFit Jump Pro Deluxe Trampoline - 305 cm - Virtufit
File Info : application/pdf, 22 Pages, 3.93MB
DocumentDocumentJump Pro Trampoline with Safety Net
User Manual
EN
INDEX
SAFETY INSTRUCTIONS CHECKLIST ASSEMBLY INSTRUCTIONS MOVING THE TRAMPOLINE MAINTENANCE BASIC TRAMPOLINE SKILLS
3 - 5 6 - 7 8 - 18 19 20 21
2
EN
Virtufit Jump Pro Trampoline with Safety Net
SAFETY INSTRUCTIONS
WARNING: Consult your child's doctor before jumping, especially for children with health problems. Read all instructions before using the trampoline. VirtuFit takes no responsibility for any injuries or material damage caused by the use of this product. Read the manual carefully before you start to assemble and/or use the trampoline. Adult supervision is
required at all times.
Recommended age 6+ years.
ATTENTION
No somersaults or flips - can cause serious injury. Jump without shoes.
Not suitable for children under 36 months - small parts, choking hazard.
The trampoline is intended for outdoor use only.
Only one user at a time. Danger of Collision hazard.
Always close the net opening before jumping.
Do not use the mat when it is wet
Empty pockets and hands before jumping
Always jump in the middle of the mat
Do not eat while jumping. It is advisable not to bounce immediately after a meal.
Do not exit by a jump
Do not use in strong wind conditions and secure the trampoline.
The trampoline shall be assembled by an adult in accordance with the assembly instructions and thereafter checked before the first use.
The max user weight is: 305 cm: 150 KGS.
Limit the time of continuous usage (make regular stops).
Virtufit Jump Pro Trampoline with Safety Net
EN
3
SAFETY INSTRUCTIONS
ADVISORY
Thistrampolineisno tintendedtobeburiedinthe ground.
Thetrampolinem ust be placed on a level surface at least 2m from any structures or obstructions
suchasfence,garage,house,overhangingbranches, laundrylinesorelectricalwires.
Donotinstallthetrampoline over concrete, asphalt or any other hard surface. Also not in proximity
ofotherconflictinginstallations,suchaspadding / swimming pools, swings, slides or climbing
frames. Anymodificationsmadebytheconsumertotheoriginal trampoline (e.g. the adding of an accessory)
shallbecarriedoutaccordingtotheinstructionsofthemanufacturer.
Inspecttrampoline/enclosurenet beforeeachuse.
Ifanaccessladderisuseditshouldberemovedwhentrampolineisnotinuse.
Makesuretherearenochildren/animals/obstructions underneath the trampoline.
Accessthetrampolinethroughthedooroftheenclosurenetonly.Making sure you securely close it
beforebouncing.Use:Ensurethedoorissecurelyclosedbeforebouncing.
Don'tintentionallyreboundofftheenclosurenetasthiswillweakenit.
Onlyattachmanufacturerapprovedaccessoriestothetrampoline and enclosure net.
Alwaysjumpinthemiddleofthematandpracticebouncetechniquessafelyw ith adult supervision
andguidance.
Warrantyclaimis excludedifthecauseof the defectisthe result of:
Maintenance assembly and repair work not performed by an official dealer.
In case of improper use, neglect and / or poor maintenance.
Failure to maintain the fitness equipment in accordance with the manufacturer's instructions.
The product has been incorporated into the soil.
Defects caused by external influences (eg climate and weather influences).
4
EN
Virtufit Jump Pro Trampoline with Safety Net
SAFETY INSTRUCTIONS
ASSEMBLY AND MAINTENANCE INSTRUCTIONS
Attention to the need to carry out checks and maintenance of the main parts (frame, suspension system, mat, padding, and enclosure) at the beginning of each season and also at regular intervals of every 2 weeks, pointing out that if these checks are not carried out, the trampoline could become dangerous.
Check all nuts and bolts for tightness and tighten when required. Check that all spring-loaded (pit pin) joints are still intact and cannot become dislodged during play. Check all coverings and sharp edges and replace when required. Retain the maintenance instruction manual. Outdoor trampolines should be equipped with a device that in strong wind conditions avoid
displacement due to wind (e.g. steel bars in the ground or loads like sand bag or water bags) and/or items catching wind like net and mat should be removed. In certain countries during winter period, the snow load and the very low temperature can damage the trampoline. It is recommended to remove the snow and store the mat and the enclosure indoor. Check that mat, padding, enclosure and soft surface are without defects. Make sure that the hook-and-loop fasteners are closed correctly during use of trampoline! Trampoline and net should be packed away in winter. Make sure all parts are dry and packed securely. Store dry to support product longevity. Always be aware of wear and tear due to weather and wind. We recommend securing the trampoline in strong winds. Tie the trampoline down with ropes attached to the trampoline pad. Tie the trampoline down in a minimum of three places distributed evenly across the trampoline frame. Do not secure the legs as these may become misaligned and ruin the trampoline. Dismantle or remove the trampoline completely, if required. It may result in great danger if the trampoline is not secured in strong winds. If the trampoline is not used for short periods of time and to avoid jump mat debris caused by fallen leaves and twigs, It's recommended usage of a Weather Cover. When the trampoline is not used for a longer period of time (e.g. during the winter). It's recommended storing the trampoline, especially the protective padding, in a dry area to support product longevity.
NOTE! Sunlight, rain, snow and extreme temperatures reduce the strength of these parts over time.
Virtufit Jump Pro Trampoline with Safety Net
EN
5
CHECKLISTTOOLKIT When
parts
oynouthoepfelAB#onotrh. eMcaakDreEtJFousSrmaunCmr,pReeainIynCPgoodTMvuIceyaOorhtoNnautvaweciatlltllhfitenhdseutpphaperltibeserl.liostwedp.aIfrtpsairntstha3erCe011Mc5amritsosnin.gP,lapcleeaaslel
C D E
Top Rail
T-Connec tor
Spring
6660
F
Leg Extension
6
G H I
WLS-oSpnhriganpgSecTdroeLowelg316
J
Screwdriver1
6
EN
Virtufit Jump Pro Trampoline with Safety Net
CHECKLIST
TOOLKIT
#
DESCRIPTION3C0M5
K
Bottom Tube
6
L
Top Tube
6
M
Top Cap
6
N
Fork Screw
O
Enclosure Net
P
FiberglassRod
Q
Sleeve
6
1
6
6
R S T
9-ShSaSppcaernednwSecrrew616
Virtufit Jump Pro Trampoline with Safety Net
EN
7
ASSEMBLY INSTRUCTIONS
Mthiesstrianmgppoalrintse:.ISfoymouetphainrtksy(obuolatsr,esmcreiswsisn,getcce.)rtaarienaplraeratsdiynaytotaucrhpeadcktoa/gine,tchaeretrfaumllypcohliencek.thestyrofoaand
Useglovestoprotectyourhandsfrombottlenecksduringassembly.Whenyou'rereadytogetstarted,
mReaakdetshuereaysoseumhbavlyeipnlsetnrtuycotifornosobmealonwdbaecfleoarne,ydoruysatraeratfmoromunotuinntgintgh.etrampoline.Incorrectmounting
willdamagethetrampolineframe:
··tsMMrpaaarmkkineepgosssu.luiFnrraeeeiltfuthrhraaeemtttoearlatdlomobwopthloatirslsipnphe(roFoIliGdpsien1pr)gll.yactwheiedllfcoraanumsleeevtjeholeingftrrsaomaurneedtt.oigUwhnateerpvne.endgcroomupndletseulyrfabceefosremainystcaalluinsegtthhee
·MakesureNOTtouseone'slegtopushagainstthetrampolinelegorframewhenloadingthesprings.
·IDtOwiNllOcaTuloseadthtehetrsapmripnoglsinoenttoowthaerpfr(aFmIGe2o).nonlyonesideofthetrampoline.Unevendistributionof
tensionfromthespringswillcausetheframetowarp(FIG2).
·fIfletxhieblter.aPmupsholdinoewfnraomnethweaprpasrtuopf,tdhoenfroatmbeethalaatrmwaerdpeadstwhieth"Qtwuaodp-leoocpkl"esaysstsehmowisnd.Tehsiegnfreadmteowbiell
level out (FIG3).
FIGUUR 7
FOTO1FOTO2
FOTO 3
NOTE!Forthenextassembly2adultsingoodphysicalconditionarerequired. Wear good shoes and
keepbalancetoavoidafall.Failuretofollsoewrioaullsininsjtururyc.tionsandwarningsexactlycouldresultin
8
EN
Virtufit Jump Pro Trampoline with Safety Net
ASSEMBLY INSTRUCTIONS
STEP 1
· ByattachingtwoLegExtension(F)to W-shapedLegs(G), toforma"U"shapedwithScrews(I) by Screwdriver(J).Repeatthisstepwiththeremainingpiecestomaketherest Ulegs. Leave to one side
when finished
NOTE! 8FT is without leg extension. This step is only suitable for 10FT and 12FT.
VirtufitJumpProTrampolinewithSafetyNetEN9
ASSEMBLY INSTRUCTIONS
· Begin by attaching Top Rails (C) to T-connectors (D). Continue until you form a large circle.
NOTE! Have a second person or use a wall to apply some resistance against the frame to help it shift into place.
· Twopeoplewillbenecessaryatthispoint to assemble the trampoline. One person lifts up the circle
frames. The other person lifts the W shaped leg tubes to a standing (vertical) position and inserts the
T-connectors into a U shaped leg tubes. Ensure the locking holes are aligned.
10
EN
Virtufit Jump Pro Trampoline with Safety Net
ASSEMBLY INSTRUCTIONS
STEP 2
NOTE! 2 adults may be required to complete placement of all springs. Springs will create high
levels of tension when assembled. Please take care not to pinch your fingers.
· Lay out the Jumping Mat(B) inside the frame.
· TakeSpring(E ) and insert end (b) into Top rail tube, then put end (a) of the spring into trampoline
Jumping Mat (B) rings.
· HoldSpringTool(H)overhandandpullspringhooktowardsToprail(C)aspictureshown; drop hook
in toframeholeuntilitlatchesoncompletely,tapitdownifhookisnotcompletelyinthehole.
Virtufit Jump Pro Trampoline with Safety Net
EN
11
ASSEMBLY INSTRUCTIONS
IMPORTANT
· Springs must be attached the right way around and fully inserted into the holes along the top of the
frame.
· It is easier to place one hand on the frame and pull the spring towards you.
· Make sure that (a) is attached to the D-rings of the jumping mat and (b) is attached to the trampoline
frame.
· The placement of the next spring must be on the opposite side of frame, then center adjacent, then
opposite. It must be done this way so the tension of the spring is spread equality.
· To ensure that you have started to fit the bed correctly, please count the spring holes in between
each top rail to make sure that you have the same number of spring holes in the top rails.
· Make sure that the D-rings on the bed, match the number of holes along the top rails. · If you notice that you have skipped a hole and D-ring connection, recount, remove and adjust
accordingly.
Installing the Protective Edge: · Lay Frame Cover (A) on outer edge, sospringsare covered. It should be fitted like a shower cap. It
should be fitted like a shower cap. Please ensure it covers all metal parts.
· Tie the strap located at the under sideoftheFrame Coverto frame. Do nottie them to thesprings.
12
EN
Virtufit Jump Pro Trampoline with Safety Net
ASSEMBLY INSTRUCTIONS
STEP 3
· ConnecttheBottomTube(K) totheTopTube(L).
· Align the hole in the bottom tube with the slot in the top tube, screw one of the screws through the
slot in the top tube and into the hole in the bottom tube using the screwdriver.
Virtufit Jump Pro Trampoline with Safety Net
EN
13
ASSEMBLY INSTRUCTIONS
S
· Firmly fix the Bottom Tube (K) to the leg extension with the Fork Screw (N) & 9 Shaped Screws (S),
then fasten them by Spanner (R).
· Slide the Sleeves(Q) on to the assembled pole tube as above picture shown.
14
EN
Virtufit Jump Pro Trampoline with Safety Net
ASSEMBLY INSTRUCTIONS
STEP 4
·SlidetheFiberglassRod(P)intothepassagesewnonthetopofthesafetynet(O),thenpushthe
FiberglassRodintotheTopCap(M),asshowninthep ictures above.
· Repeatingwiththeremainingrodsuntiltheyallconnect.Tomakethelastconnec tion, have one person standontheoppositesidefromyou, pushthe rods towards the centre of the ring until they
are in line with each other and make the last connection, as shown in the picture above
· Raise the net up into position and clip the ring into the Top tubes (L).
Virtufit Jump Pro Trampoline with Safety Net
EN
15
ASSEMBLY INSTRUCTIONS
· Connect two pieces of upper Velcros (along the top of Sleeve) to Top Caps (M).
· Connect bottom straps/clips to every few jumping mat's V-ring from under the safety pad. Attach the clips from outside as figure shows.
After assembling the trampoline, it is important that you perform the following safety checks: · Ensure all screws and bolts are tightly secured. · Look under the trampoline and check all springs are hooked securely to the frame and jumping mat rings. · Inspect the spring cover and check it is covering the springs and frame and that it is tied securely.
The VirtuFit Jump Pro Trampoline is now complete and ready to use!
16
EN
Virtufit Jump Pro Trampoline with Safety Net
ASSEMBLY INSTRUCTIONS - LADDER
TOOLKIT LADDER
#
DESCRIPTION
QTY
1
Ladder Step
2
2
Frame Leg
2
3
Nut
4
4
Bolt
4
5
Lower Frame Base
1
6
Shot Screw
2
LADDER ASSEMBLY
· Place the two frame legs (2) in a free space. Then place one of the ladder steps (1) on the bottom of each frame leg. Then slide the step up to the top bolt holes of the legs and the steps. NOTE! Make sure the diamond pattern of the stairs is facing up is targeted.
· Insert two bolts (4) through the ladder step (1) and the frame legs (2). Then tighten a nut (3) to the back of each bolt with a screwdriver (J).
· Repeat steps 1 and 2 to assemble the second ladder step. · Place the lower base frame (5) on the frame legs of the ladder (2), making sure that the screw holes
are aligned. · Insert two short screws (6) through the lower base frame (5) and the frame legs (2). Turn then tighten
each short screw with a screwdriver (J). · Test the steps to ensure they are properly attached. · Find the net opening of your safety net. Lift your protective edge and transfer the hooks from the
ladder the curved frame of the trampoline. Pull out the ladder at the base of the trampoline to make sure it hits the ground as far away from the trampoline frame as possible.
Virtufit Jump Pro Trampoline with Safety Net
EN
17
ASSEMBLY INSTRUCTIONS -LADDER
· Test the steps to ensure they are properly attached.
· Find the net opening of your safety net. Lift your protective edge and transfer the hooks from the ladder the curved frame of the trampoline. Pull out the ladder at the base of the trampoline to make sure it hits the ground as far away from the trampoline frame as possible.
18
EN
Virtufit Jump Pro Trampoline with Safety Net
MOVING THE TRAMPOLINE
INSTRUCTIONS
· Moving trampoline. If the trampoline and enclosure needs to be moved, it should be moved by two persons at least, kept horizontal, and lifted slightly.
· If necessary, the trampoline and enclosure can be taken for moving. To take the trampoline apart, follow the assembly steps in reverse order.
· If you need to move the trampoline, two people should be used at least.
· All connector points should be wrapped secured with weather resistant tape, such as duct tape. This will keep the frame intact during the move and prevent the connector points from dislocating and separating.
· When moving, lift the trampoline slightly of the ground and keep it horizontal to the ground. For any type of other move, you should disassemble the trampoline.
Virtufit Jump Pro Trampoline with Safety Net
EN
19
MAINTENANCE
DAILY MAINTENANCE
Clean and remove sweat / moisture after each use. Do not use aggressive cleaning agents Check that the trampoline is free from dust and dirt.
SEMI-ANNUAL MAINTENANCE
Inspect all bolts and nuts related to the trampoline, tighten as required.
20
EN
Virtufit Jump Pro Trampoline with Safety Net
BASIC TBRAASMICPSOKLILILNSEUSSKIINLGLSTHE TRAMPOLINE 21..SSuwtparirintgghfrtyooamnurdaayromsutsarnfeodByrieAwnsSgaoErndpJUotahsMneitdPiforranamisweei.itnhoynoeucrirhcuealadr
KNEE JUMP
1. Start jumping from a standing position, keeping your eyes on the frame.
2. Land on your knees, keep your back straight and
motion.
your body upright.
3. Bring your feet together and point your toes down 3. Bounce back to an upright position.
while in the air.
4. Keep your feet about 1 foot apart if you lands on
the bed.
BELLY JUMP
SIT JUMP
1. Start from a low jump and land on the jumping mat in a prone position.
2. Keep your head up and extend your arms on the front of the bed.
3. Push with your arms to return to one upright position.
1. Land in a sitting position with your legs parallel to the jumping mat.
2. Place your hands on the jumping mat next to your Hips.
3. Push with your hands to return to one upright position.
A certified trampoline instructor should be contacted to further develop your trampoline skills
Virtufit Jump Pro Trampoline with Safety Net
EN
21
For questions or missing parts please contact your dealer.
Adobe PDF Library 16.0 Adobe InDesign 16.4 (Macintosh)