Product Schematic Diagram

Product Specifications:

• Power supply voltage range: DC6~13.2V/DC19~28V
• Indicator light: shows (light is on, off is off)
• Automatic power off point: 11.8v/23.8v
• "OFF" key of remote disconnects the device point of battery level: 13.3v/27v.
• Remote RF frequency: 433MHZ (remote control matched, latching mode)

Product Parameters:

• Adaptive voltage: 12V/24V
• Operating temperature: 10°C~90°C
• Switching current rating: 240A
• Switch instantaneous current: 500A
• Low battery voltage point: 11.8V±0.2V/23V±0.2V
• Power off delay disconnects for 120 seconds
• Standby power consumption: 0.004A

Note:

• The product works in the 12V~13.2V DC/24~27V range. The remote control only pairs and switches the magnetic keep relay for electrical appliances.

Low Voltage Protection:

When voltage is below 11.8v/23.8v, it will automatically cut off power after a delay of 120 seconds.

Driving Voltage Protection:

When the voltage is higher than 13.2V/26.8V when driving, the remote control will be disabled to prevent accidental action. It can only be controlled by the manual switch.

ATTENTION:

1. When driving, power off, please check if the car's alternator is not working. If the battery level is low, it will automatically cut off power.
2. When driving, power off, please check the negative pole of the battery and the negative pole of the car.
3. If the negative pole of the battery and the negative pole of the car are connected incorrectly, do not POWER OFF by pressing the "off" key of the device.

Remote Control Matching Mode Description:

1. Long press the stop ("OFF") key of the device for 3 seconds. The green and red LEDs will light up, indicating that the learning code state has been entered. Press the "ON" key of the remote. The green LED of the device will blink three times, and the buzzer will ring three times. Then, the green and red LEDs will light up, indicating that the second learning code state has been entered. Press the "OFF" key of the remote. The green LED of the device will blink three times, and the buzzer will ring three times to end the learning code. In the learning code state, it will automatically end after 10 seconds if no remote key command is received.
2. Long press the stop ("OFF") key for 3 seconds. The green and red LEDs will light up, indicating that the learning code state has been entered. Then, press the "OFF" key of the device 8 times. The green LED will blink 8 times, and the buzzer will ring 8 times to clear all remote keys. The learning code state will end, and the green and red LEDs will light off.
3. The device can learn up to 5 remotes.
4. Press the "ON" key of the device or the "ON" key of the remote. The green and red LEDs of the battery level will light up. Connect the negative pole of the battery to the negative pole of the car.
5. Press the "OFF" key of the device. All LEDs on the device will light off. Disconnect the negative pole of the battery from the negative pole of the car.
6. When the battery voltage is 12V~13V/24V~27V, pressing the "OFF" key of the remote will turn off all device LEDs. Disconnect the negative pole of the battery from the negative pole of the car.
7. In the working state, when the battery voltage is over 13.3V/27V, the protection LED will light up. Pressing the "OFF" key of the remote will have no effect on the device. Connect the negative pole of the battery to the negative pole of the car.
8. In the working state, when the battery voltage is below 11.8V/23.8V, the protection LED will light up. Pressing the "OFF" key of the remote will have no effect on the device. However, the device buzzer will ring after 60 seconds, and the device will automatically turn off (disconnect the negative pole of the battery to the negative pole).

FCC Warning:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.