Installation Guide for MeTra models including: 99-8152 Vehicles With Factory Navigation, 99-8152, Vehicles With Factory Navigation, Factory Navigation, Navigation
Metra 99-8152 Dash Kit (Black) Fits 1998-2005 Lexus GS models — single-DIN radios at Crutchfield
File Info : application/pdf, 8 Pages, 970.29KB
DocumentDocument<
11\l!iTALLATIDI\I 11\l!iTRUCTIDl\l!i FDR PART 99-BISi!
APPLICATIONS
Lexus
GS SERIES 1998-2005
Not For Use In Vehicles With Factory Navigation
99-BISi!
KIT FEATURES
· DIN Radio Provision with pocket · ISO Radio Provision with pocket
KIT COMPONENTS
A) Radio Housing B) Mounting Brackets C) ISO Snap In Brackets D) ISO Trim Plate E} (2) #8 x 3/8" Screws
TOOLS REQUIRED:
Panel Removal Tool or Small Flat Blade Screwdriver
Phillips Screwdriver
ft1-800-221-0932 ~ www.metraonline.com
© COPYRIGHT 2008 METRA ELECTRONICS CORPORATION
-
99-BISi!
TABLE OF CDNTENT!i
Dash Disassembly ............................................................................ 1
Lexus
GS SERIES 1998-2005
Kit Assembly Din Mount Radio Provision with pocket..........................................................2 ISO Mount Radio Provision with pocket..........................................................3
Final Assembly ................................................................................. 4
-
gg_B15i! DA!iH Dl!iA!i!iEMBLY
LEXU!i li!i !iERIE!i 1gga-i!ODS
1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unsnap and remove vent/clock assembly from above climate controls. (Figure A)
A 0{
Bumi
B CJCJc:::::Jc:::::J
DDCJOOB
0 1~1=
B
3 Unsnap and remove ashtray assembly from below radio. (Figure B)
4 Remove two screws from behind
vent/clock assembly. (Figure C)
C
5 Remove (2) screws from behind ashtray assembly. (Figure C)
6 Unplug and remove radio/climate controls asssembly. (Figure C)
6 Remove side brackets to separate the radio from the climate controls. (Figure D)
1
-
gg_B15i! KIT A!i!iEMBLY
DIN MOUNT RADIO PROVl!ilON WITH POCKET
A
1 Snap the mounting brackets to the radio housing and secure using (2) #8 x3/8" screws provided with kit. (Figure A}
2 Align the climate controls with the
B
mounting holes in the top of the
mounting brackets. Secure the
climate controls to the brackets
using the (4) factory screws previ-
ously removed. (Figure B)
3 Slide the DIN cage into the Radio Housing assembly and secure by bending the metal locking tabs outward. (Figure C)
4 Slide the aftermarket radio into the
D
cage/radio housing assembly until it
snaps into place. (Figure D)
ti
Continue to final assembly.
-
99-BISi! KIT A!i!iEMBLY
l!iO MOUI\IT RADIO WITH POCKET
A 1 Snap the mounting brackets to the
radio housing and secure using (2) #8 x3/8" screws provided with kit. (Figure A)
2 Align the climate controls with the
mounting holes in the top of the
mounting brackets. Secure the
climate controls to the brackets using
the (4) factory screws previously
B
removed. (Figure B}
Two Screws
3 Align the holes in the ISO brackets with the holes in the radio. Mount the brackets to the radio using screws supplied with the radio. (Figure C)
4 Slide the radio/bracket assembly into the radio housing until it snaps into place. (Figure D}
5 Snap the ISO trim-plate onto the front of the assembled radio and housing. (Figure D)
Continue to final assembly.
NOTE: To remove the radio unsnap and remove the ISO trim-plate. Using a flat blade screwdriver disengage ISO brackets from the radio housing and slide radio out of radio housing.
3
-
gg.&15i! FII\IAL A!i!iEMBLY
FII\IAL A!i!iEMBLY
1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.
3 Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip,Splice, Solder, Tape.Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.
A
B
_ ..,
C ~J/ -
D
'-
····· ·
/
AJ Strip wire ends back 112"
BJ 'Twist ends together
CJ Solder
DJ Tape
METRA / EIA WIRING CODE
12V Ignition / Ace ... Red 12V Batt / Memory .. Yellow Ground ......... .. Black* Power Antenna ... .. Blue Amp Turn-On .... .. Blue / White Amp Ground ..... .. Black/ White Illumination...... .. Orange Dimmer ... ... .... Orange / White
Right Front (+) ..... Gray Right Front(-)...... Gray I Black Left Front(+) ...... White Left Front (-) ....... White / Black Right Rear(+)...... Violet Right Rear (-) ...... Violet/ Black Left Rear(+)....... Green Left Rear (-) ....... Green / Black
*NOTE: When aBlack wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer'sspecifications.
4
-
gg.a1Si!
I\IDTE!i
5
p
99-BISi! ll\l!iTRUCTIOl\l!i
ft1-800-221-0932 ~ www.metraonline.com
REV. 04/25/08
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
INST99-8152