User Guide for Laser Tools models including: 5049, 5048, 5049 Digital Torque Angle Adaptor, 5049, Digital Torque Angle Adaptor, Torque Angle Adaptor, Angle Adaptor, Adaptor
Laser 5049 Digital Torque Angle Adaptor 3/8"D 5018341050498 measuring size | workshopping.co.uk
How to use Digital Torque Angle Adaptor 3/8"D
Torque Adaptor 1. When you start the adaptor
the indicator flashes GREEN.
2. When you reach 20% from target the adaptor will flash YELLOW and an intermittent buzzer will be heard.
3. When the target is reached a RED light will appear and the buzzer is continuous.
Peak and Trace With the adaptor switched on by pressing the P/T button you can select Peak or Trace.
Peak " " This will give the value as detailed above.
Trace " " This will show the increase in increments on the display until the targeted value is reached.
Angle Functions
1. Place the adapter on a flat surface.
2. Press and release "ANG/TOQ" button.
3. The LCD panel will show "00000" followed by "0°".
4. Turn wrench either clockwise or counter clockwise.
5. The LCD panel shows the angle value measured (CCW: -5°, -6°, ...-20°etc) (CW: 5°, 6°, ...20° etc).
Angle Value
1. To increase, press and hold the (+) button to increase the current target value. The target value will appear for 10 seconds.
2. To decrease, press and hold the (-) button to decrease the current target value.
3. The target value will show for 10 seconds. After 10 seconds the value returns to "0°".
Memory (automatically saves)
Torque reading - each pre - set can save 10 sets of readings. Angle reading - stores 50 sets of memory of angle/torque readings.
To display the Memory
Torque Reading 1. Press MEM for 1 sec.
2. Press (+) or (-) to read stored readings (M1, M2, etc).
Angle Reading 3. Press MEM & (+) for 1 sec
(LCD shows "P/T".
4. Press (+) or (-) to read stored readings (r1, r2, etc).
5. Press MEM & (+) returns to Torque function ("P").
Safety precautions PLEASE READ
· Store in a clean, dry place.
· Use a soft, dry cloth to clean the adaptor and display panel.
· Never submerge in water.
· Only use the adaptor for the purpose it is intended.
· Do not exceed the permitted torque.
· Do not use the adaptor if it appears to be malfunctioning.
· Do not disassemble the adaptor.
· Do not expose the adaptor to extreme temperatures, humidity, direct sunlight or shock.
· Recalibration Hold MEM (Memory) and (Power) together. Recalibrate when necessary.
5049
Digital Torque Angle Adaptor - 3/8"D Part No. 5048
Guarantee
If this product fails through faulty materials or workmanship, contact our service department direct on: +44 (0) 1926 818186. Normal wear and tear are excluded as are consumable items and abuse.
Distributed by The Tool Connection Ltd
Kineton Road, Southam, Warwickshire CV47 0DR T +44 (0) 1926 815000 F +44 (0) 1926 815888 info@toolconnection.co.uk www.toolconnection.co.uk
www.lasertools.co.uk
www.lasertools.co.uk
Components & Features
LCD
LED Angle Peak / Trace Memory
- (Decrease) + (Increase) (Power)
Specifications
Torque Accuracy
±2%
Angle Accuracy
(± 1% of reading) + (± 1% @ angular velocity > 10º/sec < 180º/ sec) + (± 1% of Text Texture)
Preset / Memory
100 (10 sets for each preset)
Display resolution
Torque : 0.1 Angle : 1
Display range
Torque: 27- 135 Nm (19.9-99.6 lb-ft) Angle: 5 - 360°
Drive
3/8"D
Operation Mode
Peak/Trace
Unit Selection
Nm, Ft-lb, ln-lb, Kg-m
Dimension
Depth: 75 mm, Length / Width: 101 mm
Weight
290g
Battery
2 x AA
Battery Life
55hrs (continuous operation)
Ambient Temperature (Operating) 0ºC - 60ºC (31.9ºF - 139.9ºF)
Storage Temperature
-20ºC - 70ºC (-4ºF - 157.9ºF)
Operating Relative Humidity
15 to 90% (non-condensing )
Auto shut off when not in use
After 60 secs
This digital torque angle adaptor combines a torque wrench 27- 135Nm and 5-360° angle gauge.
Developments in modern technology have resulted in specifications for tightening fasteners to a lower torque threshold and then rotating the fastener through a further specified angle, thus the use of this tool is now essential.
Available in three drive sizes from 6<200Nm
How to use Digital Torque Angle Adaptor 3/8"D
Low battery warning 1. When the battery is low " "
will appear.
2. Typical battery life if 55 hours at continuous use.
3. Always remove the battery if stored for long periods.
4. Adaptor automatically shuts down if unused for 60 secs.
To replace the battery 1. Turn off power.
2. Remove the 2 Ph1 screws from the square plate on the drive side of the adaptor.
3. Remove the batteries and discard in accordance with local authority guide lines.
4. Replace the batteries with Negative (-) end towards the spring.
5. Replace the cover & screws.
Power On
1. Press the ( ) button.
2. After 2 seconds the adaptor will show 0.0 and the torque measurement selected.
3. By pressing MEM and P/T together you can scroll through the selection of torque measurements, stopping at the selected torque required.
Select Target Torque Value
1. To increase or decrease the target torque required press the + or button.
2. A fter 10 seconds the value will display 0.0.
Adobe InDesign 18.5 (Macintosh) Adobe PDF Library 17.0