No resources foundNo resources foundKramer Pro AV manufacturer - Product CategoriesKramer Pro AV manufacturer - Product Categories
User Guide for kramer models including: EXT3-XR-TR DMI Extender with USB Ethernet, EXT3-XR-TR, DMI Extender with USB Ethernet, Extender with USB Ethernet, USB Ethernet, Ethernet
Application Diagrams - Kramer Electronics
KRAMER EXT3-XR-TR EXTENS FLEXIB (EMISOR O RECEPTOR) HDBT, HDMI LOOP, USB, ETHERNET, RS-232 4k60 100M
File Info : application/pdf, 4 Pages, 569.88KB
DocumentDocumentEXT3-XR-TR Quick Start Guide Scan for full manual This guide helps you install and use your EXT3-XR-TR for the first time. Go to www.kramerav.com/downloads/EXT3-XR-TR to download the latest user manual and check if firmware upgrades are available. Step 1: Check what's in the box EXT3-XR-TR 4K60 HDMI/USB Extender 1 Power adapter and cord 1 Bracket set 4 Rubber feet 1 Quick start guide Step 2: Get to know your EXT3-XR-TR The extender device functions as a transmitter or a receiver side per DIP-switch setting (see Step 4:Connect inputs and outputs). # Feature 1 SETUP 2-way DIP-switch 2 HOST USB B 2.0 Connector 3 ACTIVE HOST LED 4 ACTIVE Rx LED 5 IN LED 6 OUT LED 7 TX LOOP 8 LINK LED 9 ON LED Function Set the HDBT Range Mode. DIP 1 DIP 2 State Description Off (up) Off (up) Standard range mode. Off (up) On (down) Ultra-long range mode. On (down) Off (up) TBD On (down) On (down) TBD Connect to the USB host (for example, a laptop) to communicate with the USB peripheral devices (for example, a smart board) connected to USB device ports on either the transmitter or the receiver sides of the extender (see Step 4:Connect inputs and outputs). Lights orange when the USB host side is active Lights green when the extender receiver function is active Lights blue when an active HDMI input signal is detected on HDMI IN. Lights blue when an output acceptor device is connected. Transmitter mode Lights blue an active signal is transmitted on the Tx LOOP port. Receiver mode N/A Lights green when the HDBT active link connection is established. Lights green when the device receives power. EXT3-XR-TR Quick Start P/N: 2 9 0 0 - 3 0 1 5 9 2 QS Rev: 1 # Feature Function 10 HDBT RJ-45 Connector Connect to the HDBT RJ-45 connector on a paired receiver/transmitter device (for example, a second EXT3-XR-TR device). 11 HDMI TX IN Connector Transmitter mode Connect to an HDMI source. Receiver Mode N/A 12 HDMI Rx OUT/Tx LOOP Connector Transmitter mode Connect to a local acceptor. Receiver mode Connect to an HDMI acceptor. 13 USB A 2.0 Connector 1 Connect to the USB local peripheral devices (for example, a USB PTZ camera). When USB Host PC is disconnected, the USB signal and charging power for this port are inactive. 14 USB A 2.0 Connectors 2-3 Connect to the USB local peripheral devices (for example, a USB camera, a soundbar, microphone and so on). When USB Host PC is disconnected, the USB charging power for this port continues to be active. 15 IR 3.5mm Mini Jack Connector Connect to an external IR emitter to control a local IR-controlled device from the remote extender (for example, EXT3-XR-TR). Connect to an IR sensor to control a remote IR-controlled device connected to the remote extender side (for example, EXT3-XR-TR). 16 RS-232 3-pin Terminal Block Connect to a controller device (for example, SL-240C) to control a remote device via serial connection (for example, the remotely connected PTZ USB camera). 17 ETHERNET RJ-45 Connector Connect to LAN. 18 SETUP 4-way DIP-switch Sets the device behavior (see Step 4:Connect inputs and outputs). 19 12V DC Power Connector Connect to the power supply. The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. Step 3: Mount EXT3-XR-TR Install EXT3-XR-TR using one of the following methods: · Attach the rubber feet and place the unit on a flat surface. · Fasten a bracket (included) on each side of the unit and attach it to a flat surface (see www.kramerav.com/downloads/EXT3 XR TR). · Mount the unit in a rack using the recommended rack adapter (see www.kramerav.com/product/EXT3 XR TR). · Ensure that the environment (e.g., maximum ambient temperature & air flow) is compatible for the device. · Avoid uneven mechanical loading. · Appropriate consideration of equipment nameplate ratings should be used for avoiding overloading of the circuits. · Reliable earthing of rack-mounted equipment should be maintained. · Maximum mounting height for the device is 2 meters. Step 4: Connect inputs and outputs Always switch OFF the power on each device before connecting it to your EXT3-XR-TR extender. Wiring the RJ-45 Connectors This section defines the HDBT pinout, using a straight pin-to-pin cable with RJ-45 connectors. EIA /TIA 568B PIN Wire Color 1 Orange / White For HDBT cables, it is recommended that the cable ground 2 shielding be connected/soldered to the connector shield. 3 4 To achieve specified extension distances, use the recommended 5 Kramer cables available at www.kramerav.com/product/EXT3 XR 6 TR. Using third-party cables may cause damage! 7 8 Setting the DIP Switches · All DIP-switches are set to OFF (up) by default Orange Green / White Blue Blue / White Green Brown / White Brown · All changes in DIP-Switches apply immediately, on-the-fly (no need to power cycle the device), except for DIP-switches 1 and 2. # Feature 1 Device Operation Mode 2 Active USB Host port 3 Define IR Pass-through 4 Programing RS-232 DIP-switch Settings OFF (up) Receiver mode is active. ON (down) Transmitter mode is active. OFF (up) Host is active. ON (down) Host is inactive (active on remote paired device). OFF (up) Pass-through the IR signal to or from the IR cable. ON (down) Add IR modulation (38kHz) to the IR output signal (applies only when the IR port is connected to an IR emitter cable). Off (up) Normal operation mode is enabled (FW programming RS-232 is inactive). On (down) FW programming RS-232 is active. Step 5: Connect power Connect the power cord to EXT3-XR-TR and plug it into the mains electricity. Safety Instructions (See www.kramerav.com for updated safety information) Caution: · For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual. · There are no operator serviceable parts inside the unit. Warning: · Use only the power cord that is supplied with the unit. · Disconnect the power and unplug the unit from the wall before installing. Step 6: Operate EXT3-XR-TR When connecting USB devices to the USB ports, note that · The recommended connected USB hub capacity is 6. · The maximum connected USB hub capacity is 15. We recommend that you use USB host PC tools, such as USB TreeView tool, to verify connected USB hubs (internal and externals) and endpoints capacity.