User Manual for Prestel models including: SW-P61R HD Video Audio Processor, SW-P61R, HD Video Audio Processor, Video Audio Processor, Audio Processor
Презентационный коммутатор 6х1 с приемником Prestel SW-P61R
File Info : application/pdf, 33 Pages, 37.41MB
DocumentDocumentPrestel SW-P61R HD Video/Audio Processor (100M) USER MANUAL Thank you for purchasing this product For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. Surge protection device recommended This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lighting strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment. Table of Contents 1. Introduction........................................................................................... 1 2. Features................................................................................................. 1 3. Package Contents................................................................................ 2 4. Specifications....................................................................................... 3 5. Operation Controls and Functions...................................................... 5 5.1 Transmitter Panle............................................................................. 5 5.2 Receiver Panle................................................................................ 9 6. Display Mode........................................................................................ 11 7. Web GUI User Guide............................................................................. 12 8. API Control Command......................................................................... 26 9. Application Example............................................................................ 31 1. Introduction HD Video/Audio Processor is a product that solves high-definition video / audio signal transmission, switch and control with integration operation. This product can switch any of these six HDMI sources to one HDMI display, and supports four sorts switch mode. It can extend HDMI / VGA HD signal, USB, network and IR control signal up to 100 meters / 329ft distances via a single CAT 5e/6 cable between transmitter and receiver, and realizes zero latency and uncompression long distance transmission from source to display device. The HDMI and VGA video resolution is up to 4K2K@30Hz and 1920×1200 @60Hz separately. This product has flexible combination, high compatibility, good scalability. It adopts integrated design that supports HD video / audio signal input, control, transmission and system management. The product is used more convenient than others product because it can control related peripherals equipment synchronously such as display terminal switch, projector curtain, etc. to improve conference or work efficiency. The product supports front panel buttons, RS-232 and Web GUI control. 2. Features HDMI 1.4, HDCP 1.4 compliant Transmitter supports 3 HDMI inputs, 1 VGA input and with 1 analog audio input Receiver supports additional 2 HDMI inputs Supports HDMI video resolution up to 4K2K@30Hz 4:4:4 and VGA video resolution up to 1920×1200@60Hz Supports signal input with seamless switch Supports 4 sorts switch mode including Full-screen, Side-by-side and Quad-view mode Supports signal input automatic recognition, zero latency, uncompression Supports smart EDID management, satisfied automatically the best match from source to display device Supports HDBaseT 2.0 transmission technology, the audio / video signal extend distance up to 100 meters / 328ft via CAT 5e/6 cable 1 / 31 Supports USB2.0 bi-directional transmission function, it can connect USB device such as smart whiteboard, touch-screen, camera, etc. Supports network access function Supports multiple control ways such as CEC, RS-232/IP, IR, Relay, etc. Supports standby automatically and wakening function for video conference system and the others control device Supports Web GUI control Supports PoC (Power over Cable) function, it means that either transmitter or receiver is powered supply by 24V/1A power adapter, the other doesn't need power supply Control is via front panel buttons, RS-232 and LAN port 3. Package Contents 1× HD Video / Audio Processor (Transmitter) 1× HD Video / Audio Processor (Receiver) 1× 24V/1.5A DC Power Adapter 1× IR Blaster cable (1.5 meters) 2× 20~60KHz IR Receiver cable (1.5 meters) 2× Mounting Ears (Receiver) 2× Mounting Ears (Transmitter) 1× User Manual 2 / 31 4. Specifications Technical HDMI Compliance HDMI 1.4 HDCP Compliance HDCP 1.4 Video Bandwidth 297MHz (10.2Gbps) Color Space RGB, YCbCr 4:4:4, YCbCr 4:2:2 Color Depth 8-bit, 10-bit, 12-bit HDMI: Up to 4K2K@30Hz (4:4:4) Video Input Resolution VGA: 640x480@60Hz ~ 1920x1200@60Hz Video Out put Resolution HDMI / HDBT3840x2160@30, 1920x1200@60, 1920x 1080@60 1280x720@60, 1280x800@60, 1360x768@60, 1024x768@60, 1680x1050@60, Auto Audio Format PCM2.0, 44.1kHz, 48kHz(24-bit) ESD Protection Human-body Model: ±8kV (Air-gap discharge) , ±4kV (Contact discharge) Connections Transmitter Input3 x HDMI [Type A, 19-pin female] 1 x VGA [DE15 female] 1 x Audio [3.5mm mini-Jack] 2 x USB [Type A, 4-pin female] Output1 x HDMI [Type A, 19-pin female] 1 x HD BaseT [RJ45 shielded] 1 x Audio [3-pin phoenix] 1 x USB [Type B, 4-pin female] Control2 x LAN [RJ45 shielded] 2 x RS-232 [3-pin phoenix] 1 x RS-232 [RJ45 shielded] 1 x IR in [3.5mm mini-Jack] 1 x IR out [3.5mm mini-Jack] 3 / 31 Receiver Input: 2 x HDMI [Type A, 19-pin female] 1 x HD BaseT [RJ45 shielded] 2 x USB [Type A, 4-pin female] Output: 1 x HDMI [Type A, 19-pin female] 1 x AUDIO [3-pin phoenix] Control: 1 x LAN [RJ45 shielded] 1 x RS-232 [3-pin phoenix] 1 x RELAY [3-pin phoenix] 1 x IR IN [3.5mm mini-Jack] 1 x IR OUT [3.5mm mini-Jack] Mechanical Housing Metal Enclosure Color Black Dimensions Transmitter: 160mm [W] x 215mm [D] x 44mm [H] Receiver: 98mm [W] x 144mm [D] x 25mm [H] Weight Transmitter:1.15Kg, Receiver: 420g Power Supply Input: AC100~240V 50/60Hz Output: DC 24V/1A (US/EU standard, CE/FCC/ULcertified) Power Consumption 18 W Operating Temperature 0°C ~ 40°C / 32°F ~ 104°F Storage Temperature -20°C ~ 60°C / -4°F ~ 140°F Relative Humidity 20~90% RH (non-condensing) Resolution / Distance (Cable Length) 4K30Hz - Meters 1080P60Hz - Meters CAT 5e/6 328ft / 100M 328ft / 100M HDMI IN / OUT 10M 15M The use of "Premium High Speed HDMI" cable is highly recommended. 4 / 31 5. Operation Controls and Functions 5.1 Transmitter Panel Front Panel HD 1 INPUT HD 2 HD 3 VGA MODE RECEIVER HDBT RX-HD 1 RX-HD 2 POWER 1 2 3 4 WINDOWS SCREEN 1 2 3 4 5 Number Name Function description 1 POWER button When the product is connected power supply, the button lamp illuminates in blue, and the button lamp is off in standby mode. Note: Through the power button for controlling power on or standby, simultaneously you need to use Web GUI setting to send corresponding power on or standby command to transmitter. Full-screen mode: Press MODE button to select full-screen mode. Then press HD1/HD2/HD3/VGA button to select input source to output, corresponding button lamp is on; Side-by-side: Press MODE button to select side-by-side mode. The HD1 and HD2 button lamp are always on, and the HD1 and HD2 button correspond to window 1 and window 2. You can select HD1/HD2/HD3/VGA input source to Window 1 and Window 2 output by front-panel button (eg: You want to select VGA source to Window 2 INPUT button 1, you need to continuously press HD1 button.) or Web GUI. Quad view mode: Press MODE button to select quad view mode. The HD1, HD2, HD3 and VGA button lamp are always on, and the HD1, HD2, HD3 and VGA button correspond to window 1, window 2, window 3 and window 4. You can select HD1/HD2/HD3/VGA input source to Window 1 / Window 2 / Window 3 / Window 4 output by front-panel button (eg: You want to select VGA source to Window 1, you need to continuously press HD1 button.) or Web GUI. Note: Press see the following "The example about button lamp" description. 5 / 31 Select HDMI/HDBT output full-screen/side-by-side/quad view display mode. 3 MODE button Long press MODE button is up to 3 seconds, the upper right corner of screen will display current IP address and serial baudrate information. The information will autom- atically quit after 5 seconds. Select HDBT/RX-HD 1/RX-HD 2 input source to receiver output, corresponding button lamp is on; HDBT: The signal for the HDMI output port of receiver is the same as the HDMI output port of transmitter. 4 RECEIVER RX-HD 1: The signal for the HDMI output port of receiver button is from RX-HD 1 input source of receiver. RX-HD 2: The signal for the HDMI output port of receiver is from RX-HD 2 input source of receiver. Note: Please see the following "The example about button lamp" description. 5 SCREEN button The SCREEN button controls the RELAY output port of receiver. Normally, it controls projector curtain lift up or down function. The button lamp will flicker when you press a SCREEN button, the flicker time of the button lamp can be set by Web GUI. The example about button lamp: full-screen mode TX HDMI: HD2 RX HDMI: HD2 full-screen mode TX HDMI: HD2 RX HDMI: RX-HD1 6 / 31 side-by-side mode: TX HDMI: side-by-side RX HDMI: side-by-side quad view mode: TX HDMI: quad view RX HDMI: quad view quad view and fullscreen mode TX HDMI: quad view RX HDMI: RX-HD2 Rear Panel 4 56 7 USB DEVICE L R USB HOST IR IN INPUT IR OUT AUDIO OUT 8 9 10 TX RX TX RX RS-232 RS-232(PASS) OUTPUT HDMI 1 HDMI 2 HDMI 3 VGA AUDIO HDBT/POC HDMI DC 24V 1 2 3 Number Name 1 INPUT Function description HDMI 1~3: HDMI input port, connect to HDMI source device such as PC or PS4 player with an HDMI cable. VGA / AUDIO: VGA input port with embedding analog audio input, connect to VGA source device such as desktop computer. 7 / 31 2 OUTPUT HDBT/POC: The HDBT port is connected HDBT port of receiver by CAT 5e/6 cable. It extends distance up to 100 meters between transmitter and receiver, and the HDBT port supports PoC function simultaneously. HDMI: HDMI output port, connect to HDMI display device such as TV or projector with an HDMI cable. 3 DC 24V Plug DC 24V/1A power supply into the unit and connect the adapter to an AC outlet. (Note: The product supports PoC function, it means that either transmitter or receiver is powered supply by 24V/1A power adapter, the other doesn't need power supply.) 4 USB DEVICE Connect to USB deivce such as key board or mouse, ect. USB HOST Connect to computer or laptop. 5 IR IN Connect to IR receiver cable. The IR signal will send to the IR OUT port of receiver. 6 IR OUT Connect to IR blaster cable. The IR signal is from the IR IN port of receiver. Connect to audio output device such as speaker. The 7 AUDIO OUT audio output signal can be selected by Web GUI or API command. 8 RS-232 9 RS-232 (PASS) Connect to a PC or control system by 3-pin phoenix connector to control the product. RS-232 serial channel. When the RS-232 setting is selected "PASS-THROUGH" option on the Control page of Web GUI. This RS-232 port and the RS-232 port of receiver is formed as pass-through channel. Otherwise, this RS-232 port is a control port to control the product. 10 LAN Connect to a PC to visit the Web GUI control page. 10/100M network switch function. Reserved for video stream nerwork interface function. 8 / 31 5.2 Receiver Panel Front Panel 1 2 3 L R HDBT/POC RX-HD 1 RX-HD 2 HDMI AUDIO DC 24V Number Name 1 INPUT 2 OUTPUT 3 DC 24V Function description HDBT/POC port: The port is connected the HDBT/POC port of transmitter via a CAT 5e/6 cable, and extends distance up to 100 meters / 328ft between transmitter and receiver. Note: The HDMI output port of transmitter and receiver will output the same signal when the HDBT port is selected by Web GUI, API or on the front panel of transmitter. RX-HD 1/2: HDMI input port, connect to HDMI source device such as DVD or PS4 with an HDMI cable. HDMI: HDMI output port, connect to HDMI display device such as TV or projector with an HDMI cable. AUDIO: Analog audio output port, connect to audio output device such as speaker. Note: This audio port is the same as audio signal for the HDMI output port. Plug DC 24V/1A power supply into the unit and connect the adapter to AC outlet. (Note: The product supports PoC function, it means that either transmitter or receiver is powered supply by 24V/1A power adapter, the other doesn't need power supply.) 9 / 31 Rear Panel TX RX POWER USB DEVICE LAN IR IN IR OUT RS-232 RELAY 1 2 3 45 6 7 Number Name Function description 1 POWER LED Power LED the product indicator. The red LED will illuminate is connected power supply. when 2 USB DEVICE Connect to USB device such as USB camera. 3 LAN Connect to a PC to visit the Web GUI control page. 10/100M network switch function. Reserved for video stream nerwork interface function. 4 IR IN Connect to IR receiver cable. The IR signal will send to the IR OUT port of transmitter. 5 IR OUT Connect to IR blaster cable. The IR signal is from the IR IN port of transmitter. 6 RS-232 RS-232 serial channel. When the RS-232 setting is selected "PASS-THROUGH" option on the Control page of Web GUI. This RS-232 port and the RS-232 (passthrough) port of transmitter is formed as pass-through channel. Otherwise, this RS-232 port is a control port to control the product. 7 RELAY Connect to projector curtain. 10 / 31 6. Display Mode This product supports four sorts display mode including full-screen, side-by-side, quad view 1 and quad view 2. Please see figure 1 display mode. Full-screen Side-by-side Quad view 1 Quad view 2 Figure 1: Display mode You can select display mode and input source about each of these windows via the front panel button, Web GUI or API command. Full-screen: Switch HD1/HD2/HD3/VGA input source separately, corresponding LED indicator on the front panel illuminates. Side-by side: Switch HD1/HD2/HD3/VGA input source to window 1 and window 2 output. The HD1 and HD2 LED indicator on the front panel always illuminate. Quad view: The quad view has two display modes (Quad view 1 and Quad view 2). Switch HD1/HD2/HD3/VGA input source to window 1, window 2, window 3 and window 4 output. The HD1, HD2, HD3 and VGA LED indicator on the front panel always illuminate. Note: If an window is selected no signal input source, the window will display factory default no signal view. But you can replace the factory default no signal view via Web GUI setting. The analog audio output of transmitter follows Window 1 by default. 11 / 31 7. Web GUI User Guide This product can be controlled by Web GUI. You have to know current IP address to connect Web GUI. The default IP address is 192.168.1.254. You can get current IP address of the product through pressing MODE button on the front panel up to 3 seconds, and the upper right corner of the HDMI output display device will display the product current IP address information. After displaying 5 seconds, the information will automatically quit. The Web GUI operation method is shown as below. Step 1: The LAN port of transmitter or receiver is directly connected the netport of a PC. Please see the following connection diagram. PC USB DEVICE L R USB HOST IR IN INPUT IR OUT AUDIO OUT TX RX TX RX RS-232 RS-232(PASS) OUTPUT HDMI 1 HDMI 2 HDMI 3 VGA AUDIO HDBT/POC HDMI DC 24V Figure 2: Web GUI connection diagram of transmitter PC TX RX POWER USB DEVICE LAN IR IN IR OUT RS-232 RELAY Figure 3: Web GUI connection diagram of receiver 12 / 31 Step 2: On the PC, go to Control Panel > Network and Internet > Network Connections > Local Area Connections, right click on it, choose Propertiers. Double click Internet Protocol Version 4 (TCP/IPv4). 13 / 31 Choose "Use the following IP address". For instance, input 192.168.1.200 as your PC's IP address, 255.255.255.0 as Subnet mask, and then click on OK, click on OK again. 169 168 101 200 255 Notice: The IP address of the PC and product should be in the same network segment. As the product's IP address is 192.168.1.254, the computer's IP should be set 192.168.1.X (X contains 1~255 except 254). Step 3: Input the product's IP address into your brower on the PC to enter Web GUI page. Then the login page will appear. 14 / 31 Select the Username from the list and enter the password. The default passwords are: Username User Admin Password user admin The function page of the username "Admin" is shown as below: Status page The Status page provides basic information about the product Model name, the installed firmware versions and the network settings. This page is visible in both User and Admin modes. 15 / 31 The buttons at the top right of the web interface are always available and provide the following functions: Clicking the Log out button will disconnect the current user. The Power On button changes the power status between On and Stand-by mode. The admin displays current login username. Main Page 16 / 31 Transmitter: · Full-screen: · Quad view 1: · Side-by-Side: · Quad view 2: Window 1 / Window 2 / Window 3 / Window 4: Display Full-screen / Side-by-Side / Quad view 1 / Quad view 2 mode and select HDMI1/HDMI2/ HDMI3/VGA input source to window 1 / window 2 / window 3 / window 4. Audio Source: Select the AUDIO OUT port on the rear panel of the transmitter output audio source including Default, HDMI1, HDMI2, HDMI3 and VGA. The Default means that the output audio source follows Window 1. Auto switch: Detect input signal source. Auto detect input signal of transmitter. The AUTO function is turned on: If a new active input source is connected, it will directly jump to the new active input source. If an active input source is pulled out, it will jump to the next active input port. The order is HD1->HD2->HD3->VGA. When this product is powered off or rebooted and these input signal sources have not been changed. Then this product is powered on again, and it will remember input signal sources before power off and reboot. If this product can not detect input source before, it will follow the order HD1->HD2->HD3->VGA to detect. 17 / 31 Auto detect input signal of receiver. The AUTO function is turned on: a) Full-screen mode: A new active input source is inserted when this product is working, it will directly jump to the new active input source. A active input source is pulled out when this product is working, it will detect all input signal sources and order is HD1->HD2->HD3->VGA-> RX-HD1->RX-HD2. When this product is powered off or rebooted and these input signal sources have not been changed. Then this product is powered on again, and it will remember input signal sources before power off and reboot. If this product can not detect input source before, it will follow the order HD1->HD2->HD3->VGA->RX-HD1->RX-HD2 to detect. a) Side-by-side or quad view mode: The auto function is only detect RX-HD1 and RX-HD2 input source. A new active input active is inserted when this product is working, it will directly jump to the new active input source. A active input source is pulled out when this product is working, it will follow the order RX-HD1->RX-HD2->HDBT to detect. When this product is powered off or rebooted and these input signal sources have not been changed. Then this product is powered on again, and it will remember input signal sources before power off and reboot. If this product can not detect input source before, it will follow the order RX-HD1->RX-HD2->HDBT to detect. Receiver Source: Select input source to the HDMI output port of receiver to output. The default is selected HDBT source. 18 / 31 Setting page Brightness: Adjust output signal brightness. The range is from 0 to 100, and default is 50. Contrast: Adjust output signal contrast. The range is from 0 to 100, and default is 50. Color: Adjust output signal color. The range is from 0 to 100, and default is 50. Overscan: Adjust output picture overscan. The range is from -10 to 0, and default is 0. The value 0 means that output picture is 100%. Output Resolution: Select output resolution. The resolution has 3840x2160 @30Hz, 1920x1200@60Hz, 1080p60Hz, 1080p50, 1280x800@60Hz, 720p 60Hz, 720p50Hz,1024x768@60Hz, Native (The Native means that compare transmitter with receiver output resolution, and then transmitter and receiver will output the best resolution simultaneously). Audio Volumn: Adjust output volumn for HDMI output port and analog audio output port of transmitter. The range is form 0 to 50 (The value 50 means that the volumn outputs 0 dB. Each level will adjust -1 dB.). Clicking the icon will switch to mute or unmute output. Audio Delay: Adjust audio output delay time for HDMI output port and analog audio output port of transmitter. The total has 10 level, each level will adjust 20ms. The maximun delay is up to 200ms, and the default value is 0 ms. 19 / 31 EDID page Input Name / EDID: Modify input source device alias name and select EDID to input source device. The EDID option has 4K2K30_2CH, 1080P_2CH, Copy Receiver HDMI out, Copy Transmitter HDMI out, USER1 Memroy, USER2 Memory, USER3 Memory Load EDID to User memory: Upload EDID *.bin file format to User 1, User 2 or User 3. Download EDID to your computer: Download INPUT-HDMI 1 / INPUTHDMI 2 / INPUT-HDMI 3 / INPUT-RX-HDMI 1 / INPUT-RX-HDMI2 EDID as file preserve. 20 / 31 System page Series baud rate: Select the serial port baud of transmitter. The default value is 19200. Sleep Timer: Select sleep time after no signal input for transmitter and receiver. The default will enter sleep mode if no signal input within 10 seconds. Boot Logo Update: Upload boot and no signal input picture.The default is loaded *.jpg format picture. Clicking the "Update" button will upload picture and display progress simultaneously. The product will automatically reboot when the upload is finished. SOC Update: Update software program. Clicking the "Update" button will update software and display progress simultaneously. The product will automatically reboot when the update is finished. Factory Reset: Reset to factory default status. Reboot: Reboot the product. 21 / 31 Control page This control page is used for controlling projector curtain lift up or down and switching display device on/off. Auto Power Settings Disable: No commands are sent. Sync_Detected: After the product is powered on, when detecting have input source signal, you can send power on command to display device through CEC RS-232/IR control. You can also control projector curtain lift up through RELAY control. When detecting have no input source signal, you can send power off command to display device through CEC /RS-232/IR. You can also control projector curtain lift down through RELAY control. 22 / 31 Switch on/off: After the product is powered on, you can send power on command to display device through CEC/RS-232/IR control. You can also control projector curtain lift up through RELAY control. After the product is in standby mode, you can send power off command to display device through CEC/RS-232/IR control. You can also control projector curtain lift down through RELAY control. RS-232 / CEC / IR: Send the command way of power on/off. Power off timeout: Set the time of Power Off command send and click "Save" button to save. The range is from 0 to 1000s. The default sends power off command after delay 300 seconds. Power On Timeout: Set the time of Power On command send and click "Save" button to save. The range is from 0 to 1000s. The default sends power on command after delay 5 seconds. RS-232 Setting: Select send command format about HEX or ASCII and set the baudrate, databit, parity and stopbit value for the RS-232 port of receiver. Power off: Input the command you need to send. After the product standby, it can automatically send the command after set time of according to Power Off Timeout. If the command is HEX format, the byte must be a even format. Power on: Input the command you need to send. After the product boot, it can automatically send the command after set time of according to Power On Timeout. If the command is HEX format, the byte must be a even format. Test the command you need to send. Click the "Save" button to save command. Note: When you select "PASS-THROUGH" option, the RS-232 (PASS) port of transmitter and the RS-232 port of receiver is formed a pass-through channel. IR control setting Display Name: Input an IR alias name. Power Off: At first, the IR function need to study the command of power off. IR receiver cable and IR blaster cable is insert to IR port. When the product is working, click the "Study" button, and then will display "study...". Using the IR remote sends power off command to IR receiver head, and then will display "Success" if the command studies success and display "Fail" means that the study is failure.Finally, the power off command has finished study and click the "Save" button to save. 23 / 31 Power On: The Power On command has similar to operation method for Power Off. Relay control: Disable: No commands are sent. Enable: The commands are sent. Screen On: Set the time of the button lamp flicker on the front panel of transmitter when the projecter curtain is lifting up. Screen Off: Set the time of the button lamp flicker on the front panel of transmitter when the projecter curtain is lifting down. Test the command you need to send. Click the "Save" button to save command. Network page IP Settings: Static: When you select Static mode, you can manually set IP adress, Subnet Mask and Gateway address. Then click "Save" button to save information. DHCP: Obtian automatically IP adress, Subnet Mask and Gateway address. HTTP Port: Set http port value. The default value is 80. Telnet Port: Set telnet port value. The default value is 23. 24 / 31 Web Login Settings Modify password function. After you selected username, please input correct old password. Then input a new password and a confirm password (The confirm password means you need to input the new password again.). Finally, click "Save" button to save information. Note: The new password can not an empty. The new password can not the same as the old password. Find Your Device: Clicking the "SHOW ME" button, all lights on the front panel of transmitter will flicker, clicking "HIDE ME" button again, these lights on the front panel of transmitter will normally display. Set Network Defaults: Click the "Set Network Default" button to reset all network configuration to factory default setting. Product Model: Modify the product model. The model will display on the Status page. Hostname: Modify the product hostname. The hostname will display on the Status page. When you use the username "user" login, the function page has only Status and Main page. The Status and Main page has the same as function for the status and Main page of the username "admin". 25 / 31 8. API Control Command This product also supports ASCII control. Connection method as below. Open any of a Serial Command tool on PC such as "Docklight" to send command to control the product. TX Gound RX 3-pin Phoenix Connector RS-232 RS-232 to USB cable PC Figure 6: 3-pin phoenix connector to USB 26 / 31 The ASCII list of the product is shown as below: ASCII Command Serial protocal: Baud rate: 115200, Data bits: 8bit, Stop bits:1, Check bit: None RS-232 Command Function description Feedback System setting help! Get the lists of all commands r model! r fw version! r status! Get device model Get Firmware version Get device current status s reset! s power x! r power! s reboot! show me x! Reset to factory defaults power on/off the device, x=0 power off x=1 power on get current power state reboot the device show/hide me (panel led blink) x=0~1 x=0 normal, x=1 blink led FW version x.xx Get the unit all status: model,fw version,hostname, ip,subnet,gateway,MAC Reset to factory defaults System Initializing... Initialization Finished! Power on System Initializing... Initialization Finished! power on /power off Reboot...System Initializing... Initialization Finished! hide me Transmitter Settings s auto switch x! Set input auto switching function on/off, x=0 off, x=1 on auto switching on r auto switch! Get auto switching function staus auto switching on s mv mode x! Set Transmitter HDMI/HDBT ouptut multi-view mode x=1~4, x=1 Full screen, x=2 Side-by-side, x=3 Quad view mode1, x=4 Quad view-mode 2, Mulit-View mode 1 r mv mode! Get Transmitter HDMI/HDBT output multi-view modeMulit-View mode 1 s in x av tx win y! Set input x to TX output window yx=1~5 y=1~4 x=1 HDMI 1, x=2 HDMI 2, x=3 HDMI 3, x=4 VGA, x=5 STREAM y=1 Window 1, y=2 Window 2, y=3 Window 3, y=4 Window 4 input 1-> window 1 r tx out! Get Transmitter HDMI/HDBT output av status Mulit-View mode 4 input 1-> window 1 input 2-> window 2 input 3-> window 3 input 4-> window 4 s tx out hdcp x! Set Transmitter HDMI output hdcp, x=0 Off, x=1 On TX HDMI hdcp status: On r tx out hdcp! Get Transmitter HDMI output hdcp status TX HDMI hdcp status: On 27 / 31 s tx out res x! Set Transmitter HDMI output resolution x=0~8 x=0 3840x2160@30Hz, x=1 1920x1200@60Hz, x=2 1080p60Hz, x=3 1080p50, x=4 1280x800@60Hz, x=5 720p60Hz, TX HDMI resolution: 3840x2160@30Hz x=6 720p50Hz, x=7 1024x768@60Hz, x=8 Native r tx out res! Get Transmitter HDMI output resolution TX HDMI resolution: 3840x2160@30Hz s tx out stream Set Transmitter HDMI output stream on/off x=0~1 x ! x=0 disable, x=1 enable Enable TX HDMI out stream r tx out stream! Get Transmitter HDMI output stream status Disable TX HDMI out stream s aspect x! r aspect! Set Transmitter HDMI output aspect x=1~2 x=1 16:9, x=2 4:3 Get Transmitter HDMI/HDBT output aspect TX HDMI aspect: 16:9 TX HDMI aspect: 16:9 s overscan x! r overscan! Set Transmitter HDMI/HDBT output overscan size x=-10~0 overscan size: 0 Get Transmitter HDMI/HDBT output overscan size overscan size: 0 s contrast x! r contrast! Set Transmitter HDMI/HDBT output contrast x=0~100 Get Transmitter HDMI/HDBT output contrast contrast50 contrast50 s brightness x! Set Transmitter HDMI/HDBT output brightness x=0~100 brightness50 r brightness! Get Transmitter HDMI/HDBT output brightness brightness50 s color x! Set Transmitter HDMI/HDBT output color x=0~100 color50 r color! Get Transmitter HDMI/HDBT output color Set Transmitter HDMI/analog audio output routing x=0~4 x=0 defult(follow the windows 1 source audio) s audio route x! x=1 HDMI 1 embedded audio x=2 HDMI 2 embedded audio x=3 HDMI 3 embedded audio x=4 VGA external audio color50 audio out: follow the windows 1 source audio r audio route! s volume x! Get Transmitter HDMI/analog audio output routing audio out: follow the windows 1 source audio Set Transmitter output volume level x=0~50 +,- volume: 50 r volume! Get Transmitter HDMI/analog output volume level Set Transmitter HDMI/analog output audio delay time x=0~10 s audio delay x! x=0 delay 0ms, x=1 delay 20ms x=2 delay 40ms, x=3 delay 60ms ..... X=9 delay 180ms, x=10 delay 200ms volume: 50 audio delay: 0ms 28 / 31 s mute x! r mute! Set Transmitter output audio mute x=0~1 x=0 unmute, x=1 mute audio unmute Get Transmitter HDMI/analog output audio mute audio mute r audio delay! Get Transmitter output audio delay time audio delay: 0ms Receiver Setting s in z av rx! r rx out! Set input x to Receiver HDMI outx=1~3 HDBT in-> Receiver HDMI x=1 HDBT IN, x=2 RX-HDMI 1, x=3 RX-HDMI 2 out Get Receiver HDMI output av status HDBT in-> Receiver HDMI out s rx out hdcp x! Set Receiver HDMI output hdcp on/off x=0~1 x=0 off, x=1 on r rx out hdcp! Get Receiver HDMI output hdcp status s rx out stream Set Receiver HDMI output stream on/off x=0~1 x ! x=0 disable, x=1 enable r rx out stream! Get Receiver HDMI output stream status RX HDMI hdcp status:On RX HDMI hdcp status:On Enable RX HDMI out stream Disable RX HDMI out stream EDID Setting Set input x EDID from z, x=0~5(0=all),z=1~7 x=0 all hdmi input, x=1 HDMI 1, x=2 HDMI 2 x=3 HDMI 3, x=4 RX-HDMI1, x=5 RX-HDMI2 s edid in x from z! z=1 4K2K30_2CH, z=2 1080P_2CH z=3 Copy Receiver HDMI out z=4 Copy Transmitter HDMI out z=5 USER1, z=6 USER2, z=7 USER3 r edid in x! Get EDID status of the input xx=0~5 x=0 all hdmi input, x=1 HDMI 1 x=2 HDMI 2, x=3 HDMI 3, x=4 RX-HDMI1 x=5 RX-HDMI2 r edid z data! Get edid data z=1~7 z=1 4K2K30_2CH, z=2 1080P_2CH z=3 Copy Receiver HDMI out z=4 Copy Transmitter HDMI out z=5 USER1, z=6 USER2 z=7 USER3 HDMI 1 EDID: 4K2K30_2CH HDMI 2 EDID: 4K2K30_2CH HDMI 3 EDID: 4K2K30_2CH RX-HDMI 1 EDID: 4K2K30_2CH RX-HDMI 2 EDID: 4K2K30_2CH 00FFFFFFFFFFFF00... Network setting r ipconfig! Get the Current IP Configauration IP Mode: Static IP: 192.168.1.254 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.1 TCP/IP port: 23 Mac address: 00:1C:91:03:80:01 29 / 31 r mac addr! s ip mode z! r ip mode! Get network MAC address Mac address: 00:1C:91:03:80:01 Set network IP mode to static IP or DHCP,z=0~1 z=0 Static IP Set IP mode:Static IP Please use "s net reboot!" command or repower device z=1 DHCP to apply new config! Get network IP mode IP mode: Static s ip addr xxx. xxx.xxx.xxx! Set network IP address r ip addr! Get network IP address s subnet xxx. xxx.xxx.xxx! Set network subnet mask Set IP address:192.168.1.254 Please use "s net reboot!" command or repower device to apply new config! DHCP on, Device can't config static address, set DHCP off first. IP address:192.168.1.254 Set subnet Mask:255.255.255.0 Please use "s net reboot!" command or repower device to apply new config! DHCP on, Device can't config subnet mask, set DHCP off first. r subnet! Get network subnet mask s gateway xxx. xxx.xxx.xxx! Set network gateway r gateway! Get network gateway s tcp/ip port x! Set network TCP/IP port (x=1~65535) Subnet Mask:255.255.255.0 Set gateway:192.168.1.1 Please use "s net reboot!" command or repower device to apply new config! DHCP on, Device can't config gateway, set DHCP off first. Gateway:192.168.1.1 Set tcp/ip port:8000 r tcp/ip port! Get network TCP/IP port tcp/ip port:8000 s telnet port x! Set network telnet port(x=1~65535) Set telnet port:23 r telnet port! Get network telnet port s net reboot! Reboot network modules telnet port:23 Network reboot... IP Mode: Static IP: 192.168.1.254 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.1 Mac address: 00:1C:91:03:80:01 Note: You can send `RS232 command' to control the product via Serial Command tool. The `Function description' explains function about the command. The "Feedback" displays whether the command sends success or not and feedback the information you need to. 30 / 31 9. Application Example Keyboard Mouse PC Speakers TP-LINK Router Transmitter USB DEVICE L R USB HOST IR IN INPUT IR OUT AUDIO OUT TX RX TX RX RS-232 RS-232(PASS) OUTPUT HDMI 1 HDMI 2 HDMI 3 VGA AUDIO HDBT/POC HDMI DC 24V PC PC PC CAT5e/6 cable Mi box PS4 40/: TV Power Supply Speakers Projector Desktop Computer Receiver HDBT/POC RX-HD 1 RX-HD 2 POWER USB DEVICE LAN HDMI L R AUDIO DC 24V TX RX IR IN IR OUT RS-232 RELAY USB Camera 31 / 31 CurtainAdobe PDF library 10.01