SØMLØS - Robot Lawn Mower and Robot Vacuum Cleaner - SOMLOS
User Manual for Somlos models including: G1S, Robotic Lawn Mower
SØMLØS G1s | Robot Lawn Mower
File Info : application/pdf, 26 Pages, 16.03MB
DocumentDocumentRoboc Lawn Mower S TABLE OF CONTENTS 01 Preface 02 Safety Instrucons 03 Transport 04-05 Know Your Mower 06 07 07-08 Guide Line Map Placement Of Dock Staon Connecon Of Boundary Wire And Dock Staon 09-10 Installaon Of Boundary Wire 11 Operate Mower 11 Charging Mower 12-19 20 Instrucon Of Mower Mower Maintenance 21 Change Cung Blades 21 Mower Storage 22 Technical Data 01 1. Preface Preface 1. Congratuations on your choice of an exceptionally high quality product. To get the best performance, your SØMLØS G1s requires knowledge of its function. Operator's Manual contains important information about your robot mower, how you install it and how you use it. 2. Read the Operator's Manual carefully and understand the contents before using your SØMLØS G1s. 1. Please read the Operator's Manual carefully and make sure you understand your robot mower, otherwise it may be damaged if incorrectly used. 2. It is not your own risk. to modify the original design of mower. All are made at 3. Check that there are no stones, branches, tools, toys or other can damage the blades and cause the mower to stop. on the lawn that 4. Never use a high-pressure washer or running water to clean the mower. 5. Do not ride or sit on the mower, mower when in children and pets should be kept away from the 6. the mower or carry it around when the power is on. 7. Do not let anyone who does not know how the robot mower works to use it. 8. 9. Do not allow the 10. Never put your hands and feet under the mower. 11. The m wireless systems such as remote controls, radio fencing or similar. types of buried electric animal 12. 13. 14. It is forbidden to cut at the lawn with a slope more than 25 degrees. 15. 16. Carefully read all warnings on the machine, ba manual. 17. Check the blades before use to ensure they are secure. 18. During thunder/lightning storms, turn off your robot mower and the power supply connected to the docking staon. 19. Do not let children and pets be around the mower. Accidently turning it on or being in the vicinity of the mower whilst operang can cause serious injury. 02 1. 2. Carry by the handle at the rear under the mower. Carry the mower blade plate away from the body. 3. 0, Correct means Incorrect means Watch out your hand and feet Read the manual carefully Don't ride and sit Pick up stones, branches, tools etc. on the lawn 03 SØMLØS 2 . Know Mower 1 2 3 4 5 12 13 14 15 14 22 04 6 7 8 9 10 11 16 17 18 19 20 21 23 24 25 26 27 1. Emergency buon 2. The control panel cover 3. Cung height adjustment cover 4. Rain sensor 5. Charging socket 6. Front wheel 7. Blade plate 8. Blade 9. Rear wheel 10. Baery cover 11. Handle 12. Cung adjustment knob 13. LCD display 14. Wi-Fi indicator light 28 15. Keyboard 16. Charging electrodes 17. Signal indicator light 18. Power connector 19. Boundary connector 20. Dock staon base 21. Operator's manual 22. Power adapter 23. Pegs for boundary wire 24. Ground screws for the dock staon 25. Installaon ruler 26. Spare blades 27. Boundary wire 28. Allen wrench 05 3. Guide Line Map As below is a general guide line map how to install the mower including placement of the dock sta Min.50cm Min.35cm Min.1.2m Min.2m Min.30cm Min.1.2m Boundary Wire Max. 1.5cm Obtuse angle Arc angle Cross 06 Sharp angle Right angle 4. a. b. c. Make sure there is minumum 2 metres straight wire in the front and 30cm straight wire in the Min. 30cm straight wire Min.2m and 5. Connecon Of BoundaryWire And Dock Staon Fig.1 07 Fig.2 200cm Fig.3 Fig.4 Follow up Fig.1 to Fig. 4 to connect the boundary Connect the adapter power cord to a 100-240 V wall socket. LED indicator status of charging staon: Solid red light: Power supply normal; blue light: Mower gets charging; Solid blue light: Loop signal normal or fully charged. 4. Secure the dock staon to the ground using the supplied ground screws by allen wrench 08 6. Installation of Boundary Wire a. ig trees, poles beds and those can be an obstacle for the mower and burying the boundary wire. b. s should not be mowed, use the boundary wire to protect them. c. A big tree with roots that can be an obstacle for the mower should be protected by burying the boundary wire. ok ok ok ok d. Make sure to lay the boundary to the ground. If the boundary wire is loose or looped on the ground, the mower will cut the wire and the signal may be not strong enough for the mower to receive. The lawn mower can detect the signal from the boundary wire within a 20m radius. Radius Max. 20m 09 e. Use a hammer to knock the pegs in the ground. care when pegs and make sure the wire is on the lawn; the distance between pegs should be approximately 100cm. The distance between pegs should be 30~50cm . f. Don't let the boundary wire 100cm g. If you intend to bury the boundary wire, make sure to place the boundary wire between 1mm and 15mm into the ground; the boundary wire should not be looped under the ground. Max.15mm Earth 10 7. 1. Place the mower in the area that inside the boundary wire. 2. lid enters into menu. Inital default password is `AAAA' 3. will work and c lid then it 8. The mower will go back to dock staon for charging when it is out of power 11 9. Instrucon Of Mower Control Panel Time, date, baery, Wifi Power buon: Power on/off. START buon: Start mowing. HOME buon: Back to staon. Menu Funcon Sub-menu 1 Spot mode Seng Schedule Zone 20 : 13 Oct . 19 98% Mowing Sub-menu 2 - Language Date&me Rain mode Work me WiFi seng Change PIN Factory reset Informaon - Status RETURN buon OK buon UP, DOWN, LEFT, RIGHT buons. A, B, C, D for PIN code. STOP buon: Emergency stop and open the control panel hatch Sub-menu 3 - English Germany France ... About Error log Work log - 12 Status Status Standby Mowing Spot Mow Returning Charging Charge to work Emergency stop Error Firmware update Meaning Mower is ready to work. Mower is mowing automacally. Mower is mowing spirally. Mower is going back to staon. Mower is charging. Mower is charging and connues to work when baery is recharged. Mower is stopped manually. Mower cannot work with errors. Firmware is updang. Power On 1. Press the STOP bu on to open the control panel lid. 2. Press the buon for 3s to power on. 3. Enter the 4-leer PIN code. The original PIN code is `AAAA'. 4. Mower waits for further operaon in standby mode. Power Off 1. Press the STOP buon to open the control panel lid. 2. Press the buon for 3s to power off. Cung Height Adjustment 1. Open the knob lid. 2. Cung height can be adjusted from 2.5cm to 5.5cm by rotang the knob. Tips: If the grass is high, it's appropriate to let mower start mowing at 5.5cm cung height. Once the grass is shorter, you can gradually lower the cung height. 13 Start 1. Press START buon under standby or charging mode. 20 : 13 Oct . 19 98% 2. Close the hatch to start. 3. If the baery is lower than 70% in charging mode, the mower enters `charge to work' mode and should get charged to 90% before mowing. Mowing 4. If the baery is lower than 30%, the mower goes back to staon automacal- ly for charging under `charge to work' mode. Work me seng 1. Press OK buon to enter sub-menu 1. 2. Select `seng' to enter sub-menu 2. 3. Select `work me'. 4. Set work me by UP and DOWN buons. (Default value is 8hrs). 5. Press OK buon to confirm seng. Mowing time OK 001 hour s Stop 1. Press the STOP buon. 2. The mower stops immediately and the control panel hatch opens. 3. The screen shows `emergency stop'. 4. Press OK or RETURN buon. 5. Enter the correct PIN code. 6. For the case that mower was working before pressing the STOP buon, the screen shows `connue to work?'. User can press OK buon to connue the previous task, or press RETURN buon to cancel it. OK Continue working? 14 Back to staon 1. Press HOME buon for 3s. 2. Close the hatch to go back to staon for 20 : 20 Oct . 19 98% charging. Charging Returning 1. Place the mower in the staon (or press HOME buon for 3s). 2. Mower will get charged to 100% before standby. 3. Mower will get charged again if baery is lower than 75%. (The electrodes of mower and charging staon must be connected). Schedule 1. Press OK buon to enter sub-menu 1. 2. Select `schedule'. 3. Press OK buon to select the desired day. 4. Press UP, DOWN, LEFT and RIGHT buons to set the start and end me. 5. Press OK buon to confirm the daily seng. 6. Repeat step 3 to 5 to complete the weekly plan. 7. Press OK buon to confirm the weekly seng. Zone 1. Press OK buon to enter sub-menu 1. 2. Select `zone'. 3. Press OK buon to select the desired zone. 4. Press UP, DOWN, LEFT and RIGHT buons to set the distance and percentage. 5. Press OK buon to confirm the seng of single zone. zone z 1 z 2 z 3 z 4 z 5 dst m 8 ------------- pct % 100 ----- 6. Repeat step 3 to 5. 7. Press OK buon to confirm the seng of all the zones. Noce: 1. The distance refers to how far the mower will go along the boundary wire before entering into the yard. The percentage refers to how oen the mower will start mowing from each zone. 2. The value of distance should be 0-500m, while the percentage should be 0-100%. The sum of percentage of each zone should be 100%. Or the seng cannot be completed. 15 Spot Mow 1. Place the machine inside the yard. 2. Press OK buon to enter sub-menu 1. 3. Select `spot mode'. 4. Close the lid to start. 20 : 13 Oct . 19 98% Rain Mode 1. Press OK buon to enter sub-menu 1. 2. Select `seng' to enter sub-menu 2. 3. Select `rain mode'. 4. Press UP and DOWN buons to disable or enable the rain mode. 5. Press OK buon to confirm seng. Spot mowing OK Disable Enable Language 1. Press OK buon to enter sub-menu 1. 2. Select `seng' to enter sub-menu 2. 3. Select `Language'. 4. Press UP and DOWN buons to select the desired language. (Will update the language very soon) 5. Press OK buon to confirm seng. 1 / 1p OK English Date and Time 1. Press OK buon to enter sub-menu 1. 2. Select `seng' to enter sub-menu 2. Date & Time OK 3. Select `date&me'. Date: 2020 / 10 / 19 4. Press UP, DOWN, LEFT and RIGHT buons to set the date and me. Time: 20 : 32 5. Press OK buon to confirm seng. 16 PIN Code 1.PIN code should be entered aer powering on, pressing STOP buon, and before clearing error status and changing PIN code. 2. If the PIN code is incorrect, the screen will show `PIN wrong, please retry.' 3. If the PIN code is entered incorrectly for 3 mes, the screen will be locked for 15s. The lock me will double for further incorrect PIN. Enter PIN Code Change PIN code 1. Press OK buon to enter sub-menu 1. 2.Select `seng' to enter sub-menu 2. 3. Select `change PIN'. 4. Enter the original PIN code. 5. Enter the new PIN code. 6. Enter the new PIN code again. (`New passwords do not match' will be shown for inconsistent passwords.) 7. Press OK buon to confirm. UP= A LEFT= C Old : New : Cfm : DOWN= B RIGHT= D Factory Reset 1. Press OK buon to enter sub-menu 1. 2.Select `seng' to enter sub-menu 2. 3. Select `factory reset'. 4. The screen shows `Reset to factory mode?'. 5. Press OK buon to confirm. OK Reset to Factory mode? 17 Error Log 1.Press OK buon to enter sub-menu 1. 2.Select `seng' to enter sub-menu 2. 3.Select `informaon' to enter sub-menu 3. 1. 2020 - 10 - 19 20:03 4. Select `error log'. FAULT_LIFTED 5.The past 10 records (including date, me 2. 2020 - 10 - 19 20:03 and error message) will be shown. FAULT_OUTSIDE_AREA Work Log 1. Press OK buon to enter sub-menu 1. 2.Select `seng' to enter sub-menu 2. 3.Select `informaon' to enter sub-menu 3. 4. Select `work log'. 5. The past 10 records (including date, me, work mode and work me) will be shown. 1. 2020 - 10 - 19 20:13 Spot mowing - 00h00m 2. 2020 - 10 - 19 20:13 Auto mowing - 00h01m About 1. Press OK buon to enter sub-menu 1. 2.Select `seng' to enter sub-menu 2. 3.Select `informaon' to enter sub-menu 3. 4. Select `about'. 5.The soware version informaon will be shown. Save Power The backlight will switch off aer 2min and the mower will power off aer 8min, respecvely, without user interference. LED indicator The backlight will switch off aer 2min and the mower will power off aer 8min, respecvely, without user interference. LED Solid red light Breathing blue light Solid blue light Status Power supply normal. Mower gets charging. Loop signal normal. Or fully charged. 18 Error Error message Mower outside Mower lied Mower lted Mower overturned Mower trapped Loop signal lost Motor fault High temp Baery abnormal Cause Soluon Mower is outside the yard. Place the mower inside the yard. Mower is lied away from the Place the mower on the ground. ground. Mower is lted too much. Place the mower in flat yard. Mower is upside down. Place the mower normally on the ground. Mower is trapped by obstacles. Remove the obstacles out of the yard. Power supply or the wire is not Check the power supply, staon, wire connected to the staon. Wire is are connected normally. broken. Blade motor or drive motor is Clear the grass or soil in cung means stuck. The motor current is too and driving wheels. Cut the high and high. thick grass by tradional lawn mower. The baery temperature is too Wait unl the temperature decreases. high. The baery is damaged. Call for help from service center. 19 10. Mower Maintenance 1. Check and clean mower regularly once a week. 2. start using the m blades should be checked once a month. 3. the blade plate must rotate easily. 4. edges should not be damaged. life grass, soil, lawn, etc. Working with dull blades gives a poor mowing results, which needs more power therefore the mower can only cover smaller area. Charge the fully at the end of the season before winter storage. If than one year, please recharge the mower again. 1. Never use a high-pressure washer or running water to clean mower. It is important to keep the mower clean. Mowing with a large amount of clippings and high slopes, mower needs more power to drive the blade plate. We recommend using a brush to clean mower undernea , and sponge or cloth to clean the top body and outer case. , damp 20 e Cutting 1. 2. 3. Turn mower upside down. 4. Rotate the skid plate so that its hole aligns with the blade 5. Unscrew the blade. Use a . 6. Pry the protection plate and blade plate a e and remove the blade and screw. 7. crew on new blade. 8. Change the blade to another side if current side is broken, worn, damaged or dulled. 1. Mower must be carefully cleaned before winter storage. Charge the fully before winter storage. 2. in dry area to protect from frost, preferably stored in the original packaging 3. you should protect boundary wire from moisture electrical tape. 1. Check whether the mower, boundary wire and charging electrode need to be cleaned before use, . If the charging or contact strips appear to be rusty, clean 2. Check whether the blades need to be changed. 3. Check whether the blades and blades plate turn easily. If not, please contact the service center for help. 21 11. Technical Data Length x Width x Height Weight Adapter Boundary Wire Length Blade Motor Blade Motor Speed Wheel Motor Bump Sensor Rain Sensor Emergency Switch Measured Noise Level Guaranteed Noise Level Mowing Mowing System Working Capacity Working Time SØMLØS G1s 50cmx35.5cmx24cm 18 Kg 29.4 V / 2.0A @ 100~240 V/ 100m BLDC 3200~3500rpm BLDC Yes Yes Yes Yes 65 4 pivoted blades 2.5-5.5 cm 18 cm (800 m2 1 Hour 22 Length x Width x Height Weight Adapter Boundary Wire Length Blade Motor Blade Motor Speed Wheel Motor Bump Sensor Rain Sensor Emergency Switch Measured Noise Level Guaranteed Noise Level Mowing Mowing System Working Capacity Working Time SØMLØS G1s+ 50cmx35.5cmx24cm 19 Kg 29.4 V / 2.0A @ 100~240 V/ 150m BLDC 3200~3500rpm BLDC Yes Yes Yes Yes 65 4 pivoted blades 2.5-5.5 cm 18 cm (1600m2 2 Hour Support: support@somlos.com Visit us here: www.somlos.com