7.to - This website is for sale! - 7 Resources and Information.
7.to - This website is for sale! - 7 Resources and Information.
Instruction Manual for VWR INTERNATIONAL models including: DS-500 Orbital Shaker, DS-500, Orbital Shaker, Shaker
17 giu 2021 — Instruction Manual. Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com ...
VWR DS-500 Orbital Shaker FOR SALE
File Info : application/pdf, 17 Pages, 2.01MB
DocumentDocumentInstruction Manual Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com TABLE OF CONTENTS Package Contents Care & Handling Maintenance & Servicing Environmental Conditions Safety Instructions OS-500 Analog Shaker DS-500 Digital Shaker DS-500E Digital Shaker DS2-500 Digital Shaker DS2-500E Digital Shaker Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 2 2 2 3,4 5,6 7,8 9,10 11,12 13-15 PACKAGE CONTENTS Orbital Shaker Instruction manual Non-skid rubber mat Power Cord CARE AND HANDLING Upon receiving your Orbital Shaker, check the outside packaging to ensure that no damage has occurred in shipment. If damage is noticed, notify the carrier immediately and file a shipping claim. 1 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com MAINTENANCE & SERVICING Your Orbital Shaker is built for long, trouble-free, dependable service. No lubrication or other technical user-maintenance is required. However, at least every three months you should: · UNPLUG THE UNIT · Remove any accumulated dirt from the base and platform · Check all controls and accessible items to make sure they are properly tightened · Tighten any item that is loose ENVIRONMENTAL CONDITIONS Non-Operating Storage: Temperature: -20 to 65oC (-4 to 149oF) Humidity: 20% to 85% RH, non-condensing Operating Conditions: Indoor use only Temperature: 10 to 40oC (50 to 104oF) Humidity: 20% to 85% RH, non-condensing Altitude: 0 to 6,562 ft. (2000M) above sea level Installation Category II and pollution degree 2 in accordance with IEC 664 SAFETY INSTRUCTIONS Warning Do not use Orbital Shaker in a hazardous atmosphere or with hazardous materials for which the unit was not designed. Also, the user should be aware that the protection provided by the equipment might be impaired if used with accessories not provided or recommended by manu- facturer, or used in a manner not specified by the manufacturer. Warning Wipe up spills immediately to prevent electrical shock. Unplug from power before cleaning and do not operate until clean up is complete. DO NOT immerse. Warning Do not operate the unit if it shows signs of electrical or mechanical damage. 2 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com OS-500 Orbital Shaker Test Tube Holder Accessory 3 Speed Knob Timer Knob Flask Clamp Accessories Weight Capacity: approx. 35 lbs (16kg) at 75 rpm approx. 5 lbs (2.3kg) at 500 rpm Orbit: .75" (1.9cm) Large Platform Accessory Speed Range: 25 to 500 rpm Operating Temp: 4oC to 40oC Voltage: 120 volts AC, 50/60 hertz 230 volts AC, 50/60 hertz Current: Less than 1 amp Fuses: 120v - 2 - 5 amp 5 x 20mm quick acting 230v - 2 - 5 amp 5 x 20mm quick acting Power: 120 watts Power Switch (run, standby, timer) Controls: On/Off Switch Speed Knob, variable 1 to 10 markings Timer Knob, variable 1 to 10 markings Timer: Timer runs from 1 to 120 minutes Dimensions: Ship weight: 7¼"H x 10"W x 15"D (18.0cmH x 27.3cmW x 38cmD) 50 lbs (23kg) Pictured with optional accessories shown on page 13-15 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com INTRODUCTION The 120v and 230v units are supplied with a 3-prong power cord that should be plugged into a standard 3-prong grounded outlet. If the cord supplied does not meet your needs, please use an approved power cord that suits local codes and electrical supply. OPERATING INSTRUCTIONS 1. Please familiarize yourself with the features and operation completely before operating the unit. 2. Be sure the power switch is in the standby position. On the 230v shaker, an additional "Power Switch" is located on the back of the unit. This switch should be in the off position. 3. Plug the cord into a properly grounded three pronged outlet. 4. Your Orbital Shaker is ready for use. 5. If this is the first time use for this unit, be sure the speed knob and timer knob are set to the off position. 6. To run in continuous mode, push rocker switch to the run position. Slowly turn speed control knob to desired speed. Unit will run until you move rocker switch to the standby position. When the test is complete, press the rocker switch to the standby position. To start the next test, begin by turning the speed knob to the 1 position. 7. To run in timed mode, set timer to desired time. Turn the speed knob to the 1 position. Press the rocker to the timed position and release. Slowly turn speed knob to desired speed, the shaker will run for the set time. OPERATION NOTES: Two 5 amp fuses prevent damage to the motor or electronics. The Orbital Shaker is designed to be balanced with the standard platform attached (platform weight is 3 lbs). At higher speeds, 200rpm and above, the shaker should be run with this weight as a minimum, on stable surface, for maximum stability. 4 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com DS-500 Digital Orbital Shaker Power Switch Speed Display & Adjustment Arrows Universal Platform Accessory (Glassware purchased separately) Run Button Stop Button Time Display & Adjustment Arrows Weight Capacity: approx. 35 lbs. (16kg) at 75 rpm approx. 5 lbs. (2.3kg) at 500 rpm Orbit: .75" (1.9cm) Speed Range: 25 to 500 rpm Operating Temp: 4oC to 40oC Voltage: Current: 120 volts AC, 50/60 hertz 230 volts AC, 50/60 hertz Less than 1 amp Fuses: Power: 120v - 2 - 5 amp 5 x 20mm quick acting 230v - 2 - 5 amp 5 x 20mm quick acting 120 watts Controls: On/Off switch LED display for Time/Speed, Up/Down Keypad for setpoint control Run/Stop keypad Timer: Digital, 1 second to 9999 minutes (increased in 1 second increments) Dimensions: 7¼"H x 10"W x 15"D (18.0cmH x 27.3cmW x 38.0cmD) Ship weight: 50 lbs. (23kg) pictured with optional accessories shown on page 13-15 5 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com INTRODUCTION The 120v and 230v units are supplied with a 3-prong power cord that should be plugged into a standard 3-prong grounded outlet. If the cord supplied does not meet your needs, please use an approved power cord that suits local codes and electrical supply. OPERATING INSTRUCTION 1. Please familiarize yourself with the features and operation completely before operating the unit. 2. Be sure the power switch is in the off position. 3. Plug the cord into a properly grounded three pronged outlet. 4. Your Orbital Shaker is ready for use. 5. Turn the Power on by depressing the left side of the rocker switch on the bottom left side of the control panel. LED displays for speed and timer will light. 6. Set speed by pressing the Up/Down arrows to the right of the speed display until you reach the desired speed. Adjust time using the Up/Down arrows to the right of the timer display. Press the run button. Timer LED will display time remaining. 7. To run in the un-timed mode, set the time to zero (0) using the Up/Down arrows to the right of the timer display. Press the run button and the unit will run until you press the stop button. Timer LED will display accumulated time. OPERATION NOTES Your Orbital Shaker automatically restarts after a power interruption. Built-in memory maintains time and speed settings during a power interruption. The Orbital Shaker is designed to be balanced with the large platform attached (platform weight is 3 lbs). At the higher speeds, 200 rpm and above, the shaker should be run with this weight as a minimum, on a stable surface for maximum stability. 6 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com DS-500E Heavy-Duty Orbital Shaker Run Button Stop Button Power Switch Speed Display & Adjustment Arrows Time Display & Adjustment Arrows Pictured with optional accessories shown on page 13-15 7 Weight Capacity: Approx. 50 lbs (22kg) at 200 rpm Approx. 10 lbs (4.5kg) at 500 rpm Orbit: .75" (1.9cm) Speed Range: 25 to 500 rpm Operating Temp: 4oC to 40oC Voltage: 120 volts AC, 50/60 hertz 230 volts AC, 50/60 hertz Current: Less than 1 amp Fuses: 120v - 2 - 5 amp 5 x 20mm quick acting 230v - 2 - 5 amp 5 x 20mm quick acting Power: 120 watts Controls: Timer: On/Off switch LED display for Time/Speed, up/down Keypad for setpoint control Run/Stop keypad Digital, 1 second to 9999 minutes (increased in 1 second increments) Dimensions: 10 3/4" x 15" x 7 1/4" (27.3W x 38D x 18.8H cm) Ship Weight: 75 lbs (34kg) Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com INTRODUCTION The 120v and 230v units are supplied with a 3-prong power cord that should be plugged into a standard 3-prong grounded outlet. If the cord supplied does not meet your needs, please use an approved power cord that suits local codes and electrical supply. The orbital shaker is equipped with an RS232 serial interface, which is used to monitor and/or control the shaker. Please contact your VWR International representative for more information. OPERATING INSTRUCTIONS 1. Please familiarize yourself with the features and operation completely before operating the unit. 2. Be sure the power switch is in the off position. 3. Plug the cord into a properly grounded three pronged outlet. 4. Your Orbital Shaker is ready for use. 5. Turn the Power on by depressing the left side of the rocker switch on the bottom left side of the control panel. LED displays for speed and timer will light. 6. Set speed by pressing the Up/Down arrows to the right of the speed display until you reach the desired speed. Adjust time using the Up/Down arrows to the right of the timer display. Press the run button. Timer LED will display time remaining. 7. To run in the un-timed mode, set the time to zero (0) using the Up/Down arrows to the right of the timer display. Press the run button and the unit will run until you press the stop button. Timer LED will display accumulated time. OPERATION NOTES: Your Orbital Shaker automatically restarts after a power interruption. Built-in memory maintains time & speed settings during a power interruption. The Orbital Shaker is designed to be balanced with the large platform attached. At the higher speeds, 200 rpm and above, the shaker should be run with this weight as a minimum, on stable surface, for maximum stability. 8 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com DS2-500-1 DS2-500-2 Large Heavy-Duty Digital Orbital Shaker shown as purchased Weight Capacity: DS2-500-1: 110 lbs (49kg) at 25 rpm 40 lbs (18kg) at 400 rpm DS2-500-2: 110 lbs (49kg) at 25 rpm 40 lbs (18kg) at 200 rpm Orbit: DS2-500-1: 1" (25.4mm) DS2-500-2: 2" (51.0mm) Speed Range: DS2-500-1: 25 to 500 rpm DS2-500-2: 25 to 300 rpm Operating Temp: 4oC to 40oC Run Button Stop Button Voltage: 120 volts AC, 50/60 hertz 230 volts AC, 50/60 hertz Current: Less than 1 amp Fuses: 120v - 2 - 5 amp 5 x 20mm quick acting 230v - 2 - 5 amp 5 x 20mm quick acting Power: 120 watts Controls: On/Off switch LED display for Time/Speed, Up/Down Keypad for setpoint control Run/Stop keypad Timer: Digital, 1 second to 9999 minutes (increased in 1 second increments) Dimensions: 25" x 28" x 8" (63.5W x 71.1D x 20.3H cm) Ship weight: 200 lbs (90kg) Power Switch Speed Display & Adjustment Arrows Time Display & Adjustment Arrows 9 Pictured with optional accessories shown on page 13-15 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com INTRODUCTION The 120v and 230v units are supplied with a 3-prong power cord that should be plugged into a standard 3-prong grounded outlet. If the cord supplied does not meet your needs, please use an approved power cord that suits local codes and electrical supply. The orbital shaker is equipped with an RS232 serial interface, which is used to monitor and/or control the shaker. Please contact your VWR International representative for more information. OPERATING INSTRUCTIONS 1. Please familiarize yourself with the features and operation completely before operating the unit. 2. Be sure the power switch is in the off position. 3. Plug the cord into a properly grounded three pronged outlet. 4. Your Orbital Shaker is ready for use. 5. Turn the Power on by depressing the left side of the rocker switch on the bottom left side of the control panel. LED displays for speed and timer will light. 6. Set speed by pressing the Up/Down arrows to the right of the speed display until you reach the desired speed. Adjust Time using the Up/Down arrows to the right of the timer display. Press the run button. Timer LED will display time remaining. 7. To run in the un-timed mode, set the time to zero (0) using the Up/Down arrows to the right of the timer display. Press the run button and the unit will run until you press the stop button. Timer LED will display accumulated time. OPERATION NOTES: A built-in program will shut power off to the motor if the table top is prevented from rotating, or the unit is overloaded. Your Orbital Shaker automatically restarts after a power interruption. Built-in memory maintains time & speed settings during a power interruption. This Orbital Shaker is optimally balanced with the 24" x 24" platform attached and 40 lbs of accessories. At higher speeds, the shaker should be run with this weight as a minimum, on stable surface for maximum stability. 10 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com DS2-500E-1 DS2-500E-2 Large High Performance Digital Orbital Shaker shown as purchased Run Button Stop Button Power Switch Speed Display & Adjustment Arrows Time Display & Adjustment Arrows 11 Pictured with optional accessories shown on page 13-15 Weight capacity: DS2-500E-1: 160 lbs (72kg) at 25 rpm 60 lbs ( 27kg) at 250 rpm DS2-500E-2: 160 lbs (29kg) at 25 rpm 60 lbs (27kg) at 175 rpm Orbit: DS2-500E-1: 1" (25.4mm) DS2-500E-2: 2" (51.0mm) Speed Range: DS2-500E-1: 25 to 500 rpm DS2-500E-2: 25 to 300 rpm Operating Temp: 4oC to 40oC Voltage: Current: Fuses: Power: Controls: Timer: Dimensions: Ship Weight: 120 volts AC, 50/60 hertz Less than 1 amp 120v - 2 - 5 amp 5 x 20mm quick acting 220v - 2 - 5 amp 5 x 20mm quick acting 120 watts On/Off switch LED display for Time/Speed, Up/Down Keypad for setpoint control Run/Stop keypad Digital, 1 second to 9999 minutes (increased in 1 second increments) 25" x 28" x 8" (63.5W x 71.1D x 20.3H cm) 230 lbs (104 kg) Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com INTRODUCTION The 120v and 230v units are supplied with a 3-prong power cord that should be plugged into a standard 3-prong grounded outlet. If the cord supplied does not meet your needs, please use an approved power cord that suits local codes and electrical supply. The orbital shaker is equipped with an RS232 serial interface, which is used to monitor and/or control the shaker. Please contact your VWR International representative for more information. OPERATING INSTRUCTIONS 1. Please familiarize yourself with the features and operation completely before operating the unit. 2. Be sure the power switch is in the off position. 3. Plug the cord into a properly grounded three pronged outlet. 4. Your Orbital Shaker is ready for use. 5. Turn the power on by depressing the left side of the rocker switch on the bottom left side of the control panel. LED displays for speed and timer will light. 6. Set speed by pressing the Up/Down arrows to the right of the speed display until you reach the desired speed. Adjust time using the Up/Down arrows to the right of the timer display. Press the run button. Timer LED will display time remaining. 7. To run in the un-timed mode, set the time to zero (0) using the Up/Down arrows to the right of the timer display. Press the run button and the unit will run until you press the stop button. Timer LED will display accumulated time. OPERATION NOTES: A Built-in program will shut power off to the motor if the table top is prevented from rotating, or the unit is overloaded. Your Orbital Shaker automatically restarts after a power interruption. Built-in memory maintains time & speed settings during a power interruption. This Orbital Shaker is optimally balanced with the 24" x 36" platform and 60 lbs of accessories attached. At higher speeds, the shaker should be run with this weight as a minimum, on stable surface, for maximum stability. 12 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com ACCESSORIES PLATFORMS Description Small Platform (13" x 13") Large Platform (18" x 18") Double Tier Braces (for stacking 18"x18" platform) Description X-Large Platform (24" x 24") Jumbo Platform (24" x 36") Universal Platform (13" x 14") Platform Usage Chart OS-500 DS-500 DS-500E DS2-500 DS2-500E Standard Platform (13" x 13") X X X Large Platform (18" x 18") X X X X-Large Platform (24" x 24") X Jumbo Platform X (24" x 36") Universal Platform X X X X X (13" x 14") 13 Caution - Install platforms on shakers before adding flask clamps tube racks or other accessories. 2 people may be needed for installation of X-large and Jumbo platforms. Caution - When using platform accessories, tighten mounting screws periodically. IF EXCESSIVE NOISE OCCURS WHILE RUNNING UNIT, stop immediately and check mounting screw tightness. Installation for Small and Large Platforms The black pad does not have to be removed. Loosen the four knobs on the shaker approximately 1/4". Place platform on shaker by aligning the slots on the bottom (underside) of the platform to the knobs, slide the platform over the knobs on the shaker. When aligned, hand-tighten the four knobs. DO NOT OVER-TIGHTEN. Installation for X-Large and Jumbo Platforms Remove black pad before mounting platforms on trays. Line up platform to installation holes on tray. Carefully place platform on tray. (hold platform with palms on outside of tray). Tighten screws into mounting holes. Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Double Tier Braces Package Contents: 4 - Tier braces 21 - Hex head screws 32 - Hex head nuts 32 - Lock washers Using 7/16" socket wrench, hex head nuts, lock washers and hex head screws, attach brackets to each of the four corners of the first (bottom) platform by aligning mounting holes on bracket to mounting holes on platform. Hold second (top) platform in place and align the mounting holes on the bracket already attached to first platform to the second platform. Tighten all screws. Follow instruction for installing large platforms on page 13. Installation for DS2-500, DS2-500E Remove black mat from the shaker. There are four mounting holes in the middle of the tray, place the platform on the tray, align the mounting screws in the platform to the mounting holes in the tray, tighten with a #2 phillips head screwdriver. DO NOT OVER-TIGHTEN Installation of foam rollers Insert knobs in the rail mounts. Insert rail mounts with knobs into support rods. Place rods with knobs and mounts added onto the platform rails. Adjust to the desired width and tighten knobs. Your platform is now ready to use. UNIVERSAL PLATFORM ATTACHMENT Rail Mount Package Contents: 6 - Foam support rods 12 - Rail mounts 12 - Knobs 1 - Platform Knob Installation for OS-500,DS-500,DS-500E Loosen the four knobs on the shaker approximately 1/4". Place platform on shaker by aligning the slots on the bottom of the platform to slide over the knobs on the shaker. When aligned, hand-tighten the four knobs. DO NOT OVER-TIGHTEN (Mounting screws are not needed for this installation). TEST TUBE RACKS Description 10-14mm tubes 16-20mm tubes 21-25mm tubes Tube Capacity 48 33 21 Package Contents: 1 - Test Tube rack 2 - Mounting knobs 2 - Washers Installation: Align mounting hole on test tube rack to mounting holes on platform, place washer between test tube rack and mounting knob. Hand-tighten mounting knobs. DO NOT OVER-TIGHTEN. 14 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com FLASK CLAMPS Description 10ml 25ml 50ml 125ml 250ml 500ml Description 1 liter 2 liter 2.8 liter 4 liter 6 liter MEDIA BOTTLE CLAMPS Description . 500ml 1000ml Package contents: Clamp, installation screw(s), extension spring (10ml and 25ml flask clamps do not require an extension spring) Installation - Line up the hole(s) in the clamp to the hole(s) in the platform you will be using, hand-tighten into place with a flathead screwdriver. Insert the flask/media bottle into clamp and wrap the supplied spring around the neck of the clamp to hold secure. 10ml - 500ml clamps are provided with 1 screw for installing on platform. 1 liter - 6 liter and media clamps are provided with 5 screws for installing on platform. Capacity Chart (13 "x 13") (18" x 18") 33cm x 34cm 45cm x 45cm Accessory Platform Platform 10ml 60 113 25ml 50ml 30 64 30 64 125ml 18 32 250ml 13 23 500ml 1 liter 6 16 4 9 2 liter 4 5 2.8 liter 1 4 4 liter 1 4 6 liter 1 1 Media Clamp 9 16 500ml Media Clamp 8 13 1000ml Test Tube Holder 1 4 MANUFACTURED BY: HENRY TROEMNER LLC 201 Wolf Drive O PO Box 87 O Thorofare, NJ 08086-0087 Phone: 856-686-1600 O Fax: 856-686-1601 www.troemner.com O email: troemner@troemner.com 580025-00 (24" x 24") 61cm x 61cm Platform 221 121 121 61 42 25 16 14 8 8 4 36 (24" x 36") 61cm x 91cm Platform 336 176 176 88 63 40 24 22 12 12 6 48 24 32 7 12 4-046-INS Rev (2/06) Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com Artisan Technology Group is an independent supplier of quality pre-owned equipment Gold-standard solutions Extend the life of your critical industrial, commercial, and military systems with our superior service and support. We buy equipment Planning to upgrade your current equipment? Have surplus equipment taking up shelf space? We'll give it a new home. Learn more! Visit us at artisantg.com for more info on price quotes, drivers, technical specifications, manuals, and documentation. Artisan Scientific Corporation dba Artisan Technology Group is not an affiliate, representative, or authorized distributor for any manufacturer listed herein. We're here to make your life easier. How can we help you today? (217) 352-9330 I sales@artisantg.com I artisantg .com