Instructions for Shikun Electronics models including: 2AR82-SKIWB921AU1, 2AR82SKIWB921AU1, 24728-SKIWB921AU1 Radio Transmitter, Radio Transmitter, Transmitter
Guangzhou Shikun Electronics Co., Ltd SKIWB921AU1 IEEE 802.11b/g/n/a/ac/ax 2T2R USB WiFi Module Integrated BT 2.1 EDR/4.2/5.2 2AR82-SKIWB921AU1 2AR82SKIWB921AU1 skiwb921au1
File Info : application/pdf, 5 Pages, 520.58KB
DocumentDocumentFCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. If power exceeds the limit and the distanceOver 20cm distance in actual use between the device and user is compliant with the requirement FCC RF Radiation Exposure Statement: The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device, for example, USB dongle like transmitters is forbidden. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body. The device must be professionally installed The intended use is generally not for the general public.It is generally for industry/commercial use. The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not normally required. the user has no access to the connector. Installation must be controlled. Installation requires special training Frequency (MHz) Antenna Type Antenna Gain (dBi) 2400-2500 5100-5900 External Antenna External Antenna Zhongshan B&T, model: AG-011320-0679 MAX gain: 3.0dBi Shenzhen KTC, model: 3D0504BK07-001 MAX gain3.5dBi Shenzhen KTC, model: SLK-KG-B3DBS-SMA(P) MAX gain3.5dBi Shenzhen KTC, model: A100-0062 MAX gain3.5dBi Guangzhou Shienthalpy Technology Co., Ltd. model: SH-230317-0001 Max gain: 3.08dBi Shenzhen KTC model: 3D0504BK07-001 MAX gain: 4.5dBi Shenzhen KTC model: SLK-KG-B3DBS-SMA(P) MAX gain5.0dBi Shenzhen KTC model: SLK-KG-B3DBS-SMA(P) MAX gain3.3dBi Shenzhen KTC model: A100-0062 MAX gain5.0dBi Guangzhou Shienthalpy Technology Co., Ltd. model: SH-230317-0001 Max gain: 4.39dBi If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: "Contains Transmitter Module FCC ID: 2AR82-SKIWB921AU1 Or Contains FCC ID: 2AR82-SKIWB921AU1" When the module is installed inside another device, the user manual of this device must contain below warning statements: 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. The host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. The end user manual shall include all required regulatory information/warning as shown in this manual, include: This product must be installed and operated with a minimum distance of 20 cm between the radiator and user body. Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1) L'appareil ne doit pas produire de brouillage; 2)L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: " Contains IC: 24728-SKIWB921AU1" any similar wording that expresses the same meaning may be used. l'appareil hôte doit porter une étiquette donnant le numéro de certification du module d'Industrie Canada, précé dé des mots « Contient un module d'émission », du mot « IC: 24728-SKIWB921AU1 » ou d'une formulation similaire exprimant le même sens, comme suit The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformité de rf. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ouémetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps. This radio transmitter 24728-SKIWB921AU1 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le présent émetteur radio 24728-SKIWB921AU1 a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'émetteur. The concrete contents to check are the following three points. 1) Should be installed so that the end user cannot modify the antenna; 2) Feed line should be designed in 50ohm Fine tuning of return loss etc. can be performed using a matching network. Le contenu concret à vérifier sont les trois points suivants. 1) doivent être installés de façon que l'utilisateur final ne peut pas modifier l'antenne 2) La ligne d'alimentation doit être conçue en 50ohm Le réglage précis de la perte de rendement, etc. peut être effectué en utilisant un réseau correspondant. Frequency (MHz) fréquences 2400-2500 5100-5900 Antenna Type types d'antenne External Antenna External Antenna Antenna Gain (dBi) Gain maximal d'antenne Zhongshan B&T, model: AG-011320-0679 MAX gain: 3.0dBi Shenzhen KTC, model: 3D0504BK07-001 MAX gain3.5dBi Shenzhen KTC, model: SLK-KG-B3DBSSMA(P) MAX gain3.5dBi Shenzhen KTC, model: A100-0062 MAX gain3.5dBi Guangzhou Shienthalpy Technology Co., Ltd. model: SH-230317-0001 Max gain: 3.08dBi Shenzhen KTC model: 3D0504BK07-001 MAX gain: 4.5dBi Shenzhen KTC model: SLK-KG-B3DBSSMA(P) MAX gain5.0dBi Shenzhen KTC model: SLK-KG-B3DBSSMA(P) MAX gain3.3dBi Shenzhen KTC model: A100-0062 MAX gain5.0dBi Guangzhou Shienthalpy Technology Co., Ltd. model: SH-230317-0001 Max gain: 4.39dBi Notice to OEM integrator Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual. Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: 2AR82-SKIWB921AU1IC: 24728-SKIWB921AU1 l'hôte doit utiliser l'instrument uniquement dans des dispositifs qui répondent à la fcc / (catégorie d'exposition rf mobile, ce qui signifie le dispositif est installé et utilisé à une distance d'au moins 20 cm de personnes. le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de conformité relatives à l'émetteur que de montrer dans ce manuel. le fabricant est responsable de la conformité de l'hôte, le système d'accueil avec le module installé avec toutes les autres exigences applicables du système comme la partie 15 b, ices - 003. accueillir le fabricant est fortement recommandé de confirmer la conformité avec les exigences de la fcc / (émetteur lorsque le module est installé dans l'hôte. le dispositif d'accueil doivent avoir une étiquette indiquant contient FCC ID:2AR82-SKIWB921AU1IC: 24728-SKIWB921AU1 The modular transmitter is only FCC authorized for the specific rule parts (Part 15.247 and Part 15.407) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), the final host product still requires Part 15 Subpart B or Part 18 etc. compliance testing with the modular transmitter installed.