Moxa - Support
Installation Guide for MOXA models including: ioLogik E1500 Series I-O Ethernet Remote, ioLogik E1500 Series, I-O Ethernet Remote
Модуль ioLogik E1512-M12-T 6078140 | Купить в розницу и оптом
File Info : application/pdf, 5 Pages, 1.25MB
DocumentDocumentioLogik E1500 Series Quick Installation Guide Ethernet Remote I/O Version 3.1, January 2021 Technical Support Contact Information www.moxa.com/support 2021 Moxa Inc. All rights reserved. P/N: 1802015000013 *1802015000013* Package Checklist · 1 ioLogik E1500 series remote I/O product · Quick installation guide (printed) Specifications Input Current Input Voltage Operating Temperature 150 mA @ 24 VDC 12 to 48 VDC -40 to 85°C (-40 to 185°F) Installation I/O Wiring DI dry contact mode DI wet contact mode (Ch-Ch isolation) DI wet contact PNP/NPN mode (No CH-CH isolation) - 2 - DIO_DI wet contact mode (no CH-CH isolation) DIO_DO sink mode Mounting and Cabling The ioLogik E1500 can be used with both DIN rail and wall mounts. When mounting on a DIN rail, release the bottom mounting kit, install the ioLogik on the rail, and then restore the bottom mounting kit to fix the ioLogik to the rail. When using wall mounting, release both the upper and bottom DIN rail kits. The ioLogik E1500 has an M12 Ethernet port for connecting either a standard direct-Ethernet or crossover-Ethernet cable via a locking M12 connector. Power and Networking Connect the +12 to +48 VDC power line to the ioLogik E1500's terminal block V+ terminal, and connect the ground from the power supply to the V- terminal. If an earth ground is available, connect the ground pin ( ). - 3 - LED Indicators Type PWR RDY LAN EXP DI DIO Color Green Off Green Green Blinking Red Green/Red Blinking Red Blinking Off Green Amber Blinking Off Green Red Off Green Off Green Off Description System power in ON System power is OFF System is ready Located System Booting-up Error Safe Mode Firmware upgrade (LED flashes for 3 seconds then stays red until restart) System is not ready 100 Mbps 10 Mbps Data Transmitting Ethernet Off Expansion Mode Ready Configuration Failure Stand-alone Mode Channel ON Channel OFF Channel ON Channel OFF System Configuration Configuration via Web Console Configuration of an ioLogik E1500 is done via the web console. · Default IP Address: 192.168.127.254 · Subnet Mask: 255.255.255.0 Note: Be sure to configure the host PC's IP address to the same subnet as the ioLogik E1500. For example, 192.168.127.253. ioSearch Utility ioSearch is a search utility that helps users locate an ioLogik E1500 on the local network. The latest version of the utility can be downloaded from Moxa's website. Load Factory Default Settings There are three ways to restore the ioLogik E1500 to the factory default settings. 1. Remove the two screws and the aluminum plate, and then press and hold the RESET button for 5 seconds. 2. Right click the specified ioLogik in the ioSearch utility and select Reset to Default. 3. Select Load Factory Default from the web console. - 4 - Modbus Address Table Refer to the user's manual for details of the ioLogik's Modbus address, or refer to the start address of the I/O channels in the web console under User-defined Modbus Addressing Default Address. How to Download the Software Step 1: Click on the following link to open the Support & Downloads search tool: http://www.moxa.com/support/support_home.aspx?isSearchShow=1 Step 2: Type the model name in the search box or select a product from the drop down box and then click Search. Step 3: Click the Software Packages link to download the latest software for the product. - 5 -