Philips PerfectCare 8000 Series Steam Generator Iron
User Manual
Introduction
Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.
Important Information
Read this user manual carefully before using the appliance. Save the document for future reference. This appliance has been designed for domestic use only. Any commercial use, inappropriate use, or failure to comply with the instructions means the manufacturer accepts no responsibility, and the guarantee will not apply.
Danger
❗ Never immerse the iron or the steam generator in water.
Warning
⚠️ Check if the voltage indicated on the type plate corresponds to the local mains voltage before connecting the appliance.
⚠️ Do not use the appliance if the plug, the mains cord, the steam supply hose, or the appliance itself shows visible damage, or if the appliance has been dropped or leaked.
⚠️ If the mains cord or the steam supply hose is damaged, it must be replaced by Philips, a service centre authorized by Philips, or similarly qualified persons to avoid a hazard.
⚠️ Never leave the appliance unattended when it is connected to the mains.
⚠️ This appliance can be used by children aged 8 or above and by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, if they have been given instructions in safe use or supervision to ensure safe use and awareness of hazards. Do not allow children to play with the appliance.
⚠️ Keep the iron and its mains cord out of the reach of children aged 8 or under when the appliance is switched on or cooling down.
⚠️ Children are only allowed to clean the appliance and perform descale or Calc-Clean procedures under supervision.
⚠️ Do not let the mains cord and steam supply hose come into contact with the hot soleplate of the iron.
⚠️ Before performing descale or calc-clean, unplug the appliance and cool it down for at least 2 hours to avoid risk of burns.
⚠️ Do not open and remove the EASY DE-CALC knob from the steam generator during use or when it is still hot or under pressure.
⚠️ If steam or hot water droplets escape from under the EASY DE-CALC knob when the appliance heats up, switch off the appliance, cool it down for at least 2 hours, and tighten the EASY DE-CALC knob. If steam continues to escape, switch off the appliance and contact the authorized Philips service center.
⚠️ Do not use any other cap on the steam generator than the supplied EASY DE-CALC knob.
⚠️ Keep fingers or hands away from the soleplate when steam is activated to avoid burns during ironing.
⚠️ Never direct the steam towards persons or animals.
Caution: Hot Surface
Surfaces are liable to get hot during use (for irons with a hot symbol marked on the appliance).
Caution
? Only connect the appliance to an earthed wall socket.
? The appliance must be used and placed on a flat, heat-resistant surface. When placing the iron on its stand, ensure the surface is stable. The iron stand is the heel of the iron or the part where the iron rests when not in use.
? Check the mains cord and supply hose regularly for possible damage.
? The plug must only be connected to a socket with the same technical characteristics as the plug.
? Fully unwind the mains cord before plugging it into the wall socket.
? The iron platform and the soleplate can become extremely hot and may cause burns if touched. Do not touch the iron platform when moving the steam generator.
? When finished ironing, cleaning, filling or emptying the steam generator, or even when leaving the iron for a short while, place the iron back on the iron platform, switch off the appliance, and remove the mains plug from the wall socket.
? Unplug the appliance and cool it down for at least 2 hours to avoid burns. Descale or calc-clean the steam generator according to the instructions in the 'Cleaning and maintenance' chapter.
? Do not add perfumed water, water from the tumble dryer, vinegar, starch, descaling agents, ironing aids, chemically descaled water, or other chemicals, as they may cause water leakage, brown staining, or damage to your appliance.
? This appliance is intended for household use only.
Electromagnetic Fields (EMF)
This appliance complies with applicable standards and regulations regarding exposure to electromagnetic fields.
Recycling
♻️ Do not throw away the product with normal household waste at the end of its life. Hand it in at an official collection point for recycling. By doing this, you help preserve the environment.
♻️ Follow your country's rules for the separate collection of electrical and electronic products. Correct disposal helps prevent negative consequences for the environment and human health.
Warranty and Support
Versuni offers a two-year warranty after purchase. This warranty is not valid if a defect is due to incorrect use or poor maintenance. Our warranty does not affect your statutory consumer rights. For more information or to invoke the warranty, please visit www.philips.com/support.
Product Overview
The Philips PerfectCare 8000 Series is a steam generator iron designed for efficient and effective ironing. It features various modes and functions to enhance your ironing experience.
Key Features and Modes
- Auto-off Function: The appliance switches off automatically when not in use for 10 minutes to save energy and ensure safety.
- Vertical Ironing: Allows for steaming garments while they are hanging, ideal for curtains or delicate items.
- OptimalTEMP Technology: Guarantees no burns and no settings adjustment, suitable for all ironable fabrics.
- Max Mode (Strong Steam Mode): Provides maximum steam output for tough creases.
- Steam Boost: Delivers an extra burst of steam for stubborn wrinkles.
- Auto Mode: Steam is automatically released when the iron is moved, and stops when stationary or lifted.
- Vertical Mode: Specifically for steaming garments vertically.
- Speed Mode (PSG81XX): Adjusts steam output based on movement speed for efficient ironing.
Filling the Water Tank
Steps:
- Open the water tank cap.
- Fill the water tank with clean water up to the MAX indicator (1.8 liters).
- Close the water tank cap securely.
The appliance features a 'Water tank empty' indicator light.
Usage Warnings
The manual provides visual guidance on correct ironing practices:
- ✔️ Ironing a shirt correctly.
- ❌ Incorrect ironing of a shirt.
- ✔️ Ironing a shirt correctly.
- ❌ Do not iron a person.
- ✔️ Ironing a shirt correctly.
Preparing for Use
Follow these steps before starting to iron:
- Plug the appliance into an earthed wall socket.
- Press the power button.
- Wait approximately 2 minutes for the appliance to heat up.
- Steam for 30 seconds horizontally before ironing to prevent water leaking.
Maintenance
Descaling the Appliance
Regular descaling is recommended to maintain performance. Follow the specific steps provided in the manual (Sections A and B illustrate different descaling procedures, typically involving filling with 900ml of water and running the cycle).
Descaling the Soleplate
Detailed steps are provided for descaling the soleplate, which may involve unplugging, cooling, filling with water, and cleaning with a damp cloth. This process is recommended monthly.
Storage
Proper storage ensures the longevity of your appliance:
- Unplug the appliance and allow it to cool down completely.
- Empty any remaining water from the steam generator.
- Clean the soleplate with a damp cloth.
- Wrap the power cord neatly.
- Store the steam hose securely.
- Place the iron on its stand.
- Store the steam generator in a safe place.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| The ironing board cover becomes wet or there are water droplets on the garment during ironing. | Steam has condensed on the ironing board cover after a long ironing session. You have an ironing board cover not designed for high steam output. |
Replace the ironing board cover if the foam material has worn out. Add an extra layer of felt material under the ironing board cover to prevent condensation. Felt can be purchased at a fabric shop. |
| Water droplets come out of the soleplate. | The steam in the hose has cooled down and condensed into water. | Steam away from the garment for a few seconds. |
| Steam and/or water come out from under the EASY DE-CALC knob. | The EASY DE-CALC knob is not tightened properly. The rubber sealing ring of the EASY DE-CALC knob is worn. |
Switch off the appliance, let it cool for 2 hours, unscrew and properly retighten the EASY DE-CALC knob. If the problem persists, contact an authorized Philips service center for a replacement knob. |
| Dirty water and impurities come out of the soleplate or the soleplate is dirty. | Impurities or chemicals in the water have deposited in the steam vents and/or on the soleplate. Too much scale and minerals have accumulated inside the appliance. |
Clean the soleplate with a damp cloth. Descale the appliance regularly as per the 'Descaling appliance' chapter. |
| The iron leaves a shine or an imprint on the garment. | The surface being ironed was uneven, such as ironing over a seam or fold. | PerfectCare is safe on all garments. Shine/imprints are not permanent and will wash out. Avoid ironing over seams or folds, or place a cotton cloth over the area to prevent imprints. |
| The appliance does not produce any steam. | There is not enough water in the tank (water tank empty light flashes). The appliance is not hot enough to produce steam. You did not press the steam trigger. The water tank is not placed properly. Automatic steam or speed mode is off. |
Fill the water tank. Wait until the 'iron ready' light is continuously lit. Press and hold the steam trigger while ironing. Slide the water tank back in firmly. Ensure the desired mode's indicator light is on. |
| The appliance has switched off. The on/off button light flashes. | The auto-off function is activated automatically after more than 10 minutes of inactivity. | Press the power on/off button to switch the appliance on again. |
| The appliance produces a pumping sound and/or a metallic rattling sound. | This is caused by water being pumped into the boiler. This is normal and more frequent in Speed and Auto modes. | If the pumping sound is continuous and excessive, switch off the appliance, unplug it, and contact an authorized Philips service center. |
Technical Specifications
Product: Philips Steam Generator Iron
Model: PSG8160 (Also compatible with PSG80XX, PSG81XX series)
Voltage: 220V~
Frequency: 50Hz
Rated Input Power: 2000W
Country of Origin: Indonesia
Manufacturer/Responsible Party: Versuni Holding B.V.
Hazardous Substances Information
| Component Name | Lead (Pb) | Mercury (Hg) | Cadmium (Cd) | Hexavalent Chromium (Cr(VI)) | Polybrominated Biphenyls (PBB) | Polybrominated Diphenyl Ethers (PBDE) |
|---|---|---|---|---|---|---|
| Main body | X | O | O | O | O | O |
| Iron body | X | O | O | O | O | O |
| Power plug | X | O | O | O | O | O |
Note: 'O' indicates that the content of the hazardous substance in all homogeneous materials of the component is within the limit requirements specified in GB/T 26572. 'X' indicates that the content of the hazardous substance in at least one homogeneous material of the component exceeds the limit requirements specified in GB/T 26572.
Issue Date: 2023-07-19
PHILIPS and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of Versuni Holding B.V., and Versuni Holding B.V. is the warrantor in relation to this product.
Philips Customer Service Support - Home | Philips
