Owner's Manual for AMP models including: AMP25B, AMP25B DC Tubular Motor, DC Tubular Motor, Tubular Motor, Motor
Turnils North America AMP25BV5 DC Tubular Motor with rechargeable battery 2AU29AMP25BV5 2AU29AMP25BV5 amp25bv5
IC Radiation Exposure Statement/Déclaration d'exposition aux radiations: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Button Instructions LED light P1 button Lithium Battery Switch Lower Channel LCD Display Up Stop P2 Down Higher Channel The paired transmitter has passed FCC ID certification, FCC ID:2AU29AMP15REMV3 ! Essential Settings The steps in factory mode must be completed to ensure proper operation. P2 Switch 1. Pair / Unpair Remote Control a. Press "P1" button (about 2 sec) on Action on a. the motor head until motor jog x1 and Motor beep x1. b. In the next 10 secs, press and hold "Stop" button on the remote control until Motor Response motor jog x2 and beep x3. Action on b. Remote Control * Repeat the same procedure to unpair remote control. Motor Response P1 Jog x1 Beep x1 Stop Jog x2 Beep x3 2. Change Motor Direction (if necessary) Press "Up" or "Down" button to check if the shade moves in the desired direction. If you need to reverse the direction, press and hold (about 2 sec) "Up" and "Down" buttons simultaneously until motor jog x1 and beep x1. Action on Remote Control Motor Response *The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only switch direction by pressing P1 button (See P1 button instructions). + Up Down Jog x1 Beep x1 3. Setting the Upper and Lower Limits 3.1 Set Upper Limit Action on a. Remote Control a. Press "Up" button to raise the shade, Up then press "Stop" button when it is in the desired upper limit. Motor Response b. Press and hold (about 2 sec) "Up" and "Stop" buttons simultaneously until motor jog x2 and beep x3. b. Up + Stop Jog x2 Beep x3 3.2 Set Lower Limit a. Press "Down" button to lower the shade, then press "Stop" button when it is in the desired lower limit. b. Press and hold (about 2 sec)"Down" and "Stop" buttons simultaneously until motor jog x2 and beep x3. Action on a. Remote Control Down Motor Response b. + Down Stop Jog x2 Beep x3 *If you exit the limit setting status before you finish the limit settings, the motor will take the previous existing limits. Factory Mode Complete User Mode Begins 4. Adjust Limits 4.1 Adjust the Upper Limit a. Press and hold (about 5 sec) "Up" and "Stop" buttons simultaneously until motor jog x1 and beep x1. b. Use "Up" button to raise the shade to the desired highest position, and use "Up" or "Down" button to do the final adjustment if necessary. c. Press and hold (about 2 sec) "Up" and "Stop" buttons simultaneously until motor jog x2 and beep x3. Action on a. Remote Control Motor Response Action on c. Remote Control Motor Response + Up Stop Jog x1 Beep x1 + Up Stop Jog x2 Beep x3 4.2 Adjust the Lower Limit a. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jog x1 and beep x1. b. Use "Down" button to lower the shade to the desired lowest position, and use "Up" or "Down" button to do the final adjustment if necessary. c. Press and hold (about 2 sec) "Down" and "Stop" buttons simultaneously until motor jog x2 and beep x3. Action on a. Remote Control + Down Stop Motor Response Jog x1 Beep x1 Action on c. Remote Control + Down Stop Motor Response Jog x2 Beep x3 b. Up b. Down 5. Favorite Position 5.1 Set Favorite Position a. Use "Up" or "Down" button to move the shade to desired Favorite position. b. Press one "P2" button on the back of remote control until motor jog x1 and beep x1. c. Press and hold (about 2 sec) "Stop" button until motor jog x1 and beep x1. d. Once more, press and hold (about 2 sec) "Stop" button until motor jog x2 and beep x3. Action on a. Remote Control Motor Response Action on c. Remote Control b. P2 or Up Down or d. Stop Stop Jog x1 Beep x1 Motor Response Jog x1 Beep x1 Jog x2 Beep x3 5.2 Send Shade to Favorite Position Action on Press and hold (about 2 sec) "Stop" Remote Control Stop button, motor will move to Favorite position. Shade Response or 5.3 Delete Favorite Position a. Press one "P2" button until motor jog and beep x1. b. Press and hold (about 2 sec) "Stop" button until motor jog and beep x1. c. Once more, press and hold (about 2 sec) "Stop" button until motor jog x1 and long beep x1. Action on a. Remote Control Motor Response Action on c. Remote Control Motor Response P2 b. Jog x1 Beep x1 Stop Jog x1 Beep x1 6. Roller Mode and Sheer Mode 6.1 Roller Shade Mode - continue movement after a short press Default Mode a. Press and hold (about 5 sec) "Up" and "Down" buttons simultaneously until motor jog x1. b. Press and hold (about 2 sec) "Stop" button until motor jog x2 and beep x3. Action on a. Remote Control Motor Response Action on b. Remote Control Motor Response + Up Down Jog x1 Stop Jog x2 Beep x3 Stop Jog x1 Beep x1 6.2 Sheer Shade Mode - jog movement after a short press (continue movement after a long press) a. Press and hold (about 5 sec) "Up" and "Down" buttons simultaneously until motor jog x1. b. Press and hold (about 2 sec) "Stop" button until motor jog x1 and beep x1. Action on a. Remote Control Up Motor Response + Down Jog x1 Action on b. Remote Control Motor Response Stop Jog x1 Beep x1 7. Add or Remove Additional Remote 7.1 Using Current Remote Control a. On the current remote control, press one "P2" button until motor jog x1 and beep x1. b. Once more, on the current remote control, press one "P2" button until motor jog x1 and beep x1. c. On the New remote control, press one "P2" button until motor jog x2 and beep x3. Action on a. Current Remote Control Remote Control P2 Motor Response Jog x1 Beep x1 Action on c. New Remote Control Remote Control P2 b. Current Remote Control P2 Jog x1 Beep x1 *Repeat the same procedure to remove additional remote control. Motor Response Jog x2 Beep x3 7.2 New Remote Control Follow instructions under the section 1. Pair / Unpair Remote Control 8. Adjust Motor Speed 8.1 Acceleration Speed a. Press one "P2" button until motor jog x1 and beep x1. b. Press "Up" button until motor jog x1 and beep x1. c. Once more, press "Up" button until motor jog x2 and beep x1. Action on a. P2 Remote Control b. Up Motor Response Action on c. Remote Control Jog x1 Beep x1 Up Jog x1 Beep x1 Motor Response Jog x2 Beep x1 8.2 Deceleration Speed a. Press one "P2" button until motor jog x1 and beep x1. b. Press "Down" button until motor jog x1 and beep x1. c. Once more, press "Down" button until motor jog x2 and beep x1. Action on a. Remote Control Motor Response Action on c. Remote Control P2 Jog x1 Beep x1 Down b. Down Jog x1 Beep x1 *If the motor has no response, it already has a Maximum or Minimum speed. Motor Response Jog x2 Beep x1Adobe Illustrator(R) 24.0 Adobe PDF Library 15.0