Bewello BW2100 Wall Heater - User Manual

Introduction

Dear Customer! Thank you for choosing our product. We hope you enjoy using it for a long time. The Bewello BW2100 is a new generation wall heater, an essential accessory for homes, winter rooms, dormitories, and offices. Its wall-mounting design ensures safe use, eliminating the fear of tipping over or accidental contact by children. The included remote control allows for easy adjustment of heating levels, and the built-in thermostat makes it suitable for occasional full heating of smaller rooms.

Key Features

• ✅ Easy to install
• ? LED display
• ? Comfortable remote control
• ⏰ Temperature setting
• ⏰ Timer function
• ?️ Overheating protection
• ? Window opening detection

Specifications

Safety Regulations and Warnings

⚠️ DANGER!

General Advice

Danger of suffocation! Keep packaging out of reach of children. The appliance is for adult use only. Choose a storage location inaccessible to children. Ensure children do not play with the appliance.

Danger of Electric Shock

⚡ Never operate with wet hands. Touching the device, power plug, cable, or buttons with wet hands is strictly prohibited. Connect only to AC power with the correct voltage. Ensure proper grounding and a Fi-relay (30 mA) circuit breaker. Do not point the device directly at electrical equipment. Do not use near bathtubs, showers, swimming pools, or sinks. Unplug by grabbing the mains plug. Never run the appliance cable across the front of the appliance.

Operation

Ensure environmental regulations are followed before use. Do not use near explosive materials. Follow local safety regulations for special locations (e.g., petrol stations, pools). Place the appliance horizontally and stably to prevent tilting. Do not cover the appliance with any material (sheets, blankets). Keep at least 2 meters away from furniture, objects, or walls to prevent fire. Do not operate from a socket with a timer. The appliance is not suitable as a primary heating source; it is designed for intermittent (short-term) heating.

❗ WARNING!

General Advice

Use only for its intended purpose. Pay attention to the physical safety of yourself and others, especially children. Only persons who have read, understood, and can operate the device should use it. Individuals with reduced mental, physical, or sensory capabilities, and children, should not use the appliance. After use, ensure the hot appliance cools down in a well-ventilated area to prevent injury. Inform others about the appliance's operating status.

Risk of Electric Shock

Connect only to a mains socket that is safe to operate or has been installed by a specialist according to IEC 60364-1. Before each use, check that the appliance, mains cable, and connectors are intact. Use only undamaged devices. If damage is found, do not use the appliance and contact a specialist. During use, monitor the mains cable's integrity and avoid edges or objects that could damage it. Avoid extension cords or splitters, as they pose a danger. Always unplug the appliance when not in use. Maintenance must only be performed with the mains plug removed.

Risk of Burns

? Never touch the heating part (lower section) of the heater. Always allow the appliance to cool down before touching the housing to avoid burns. Operate only when fully assembled with factory accessories. Replace any damaged parts before use. Allow the appliance to cool down completely in a well-ventilated place before storing. Periodically check during use that the appliance is not overheating and that ventilation openings are not blocked.

CAUTION!

General Advice

? Do not use if the device has been dropped or struck and is visibly damaged. Safety devices must be used as intended; modifying or disabling them is strictly forbidden.

Operation

Operate and store the device as described. Always check the integrity of the appliance, cable, plug, and accessories. Do not use if damaged.

ATTENTION!

Operation

? Use the appliance only at temperatures above 0 °C to avoid condensation and electric shock. Never leave the appliance unattended when connected to the mains. Protect from moisture and water. Do not store outdoors in fluctuating temperatures.

Attention!

Certain parts of the product can become hot and cause burns. Increased attention is required near children.

Special Requirements

Attention!

The heater does not have a room temperature control device. Do not use it unattended in a room with individuals who cannot leave.

Attention!

Leave at least 30 cm of space above the radiator and 200 cm in front of it. Never use the radiator in a room with flammable, explosive oil, gasoline, or gas.

Installation Instructions

Install the appliance at least 180 cm high on the wall, ensuring at least 30 cm distance from the ceiling and that the outlets face downwards. It is recommended to place the lower part of the device at a height of 180 cm from the ground to avoid accidental accidents. The device must only be mounted horizontally.

Diagram description: Required clearances for wall mounting. Shows a minimum of 30 cm space above the heater and 200 cm space in front of it. The heater should be mounted at least 180 cm high from the ground.

Diagram description: Wall mounting details. Shows the distance between mounting holes must be exactly 330 mm. Drilling requires a 6 mm drill bit to a depth of at least 26 mm.

Diagram description: Mounting positions. 'Position A' shows placing the heater onto the screws, and 'Position B' shows sliding it to achieve a stable attachment.

Installation Steps

The included mounting accessories are suitable for brick, concrete, and silicate walls. For plasterboard walls, installation requires a horizontal support structure. Ensure the wall has adequate load capacity and power supply access. For plasterboard, use a special drywall anchor, not the one included. For wooden surfaces, pre-drilling and dowels are not necessary.

1. Using a spirit level and pencil, draw a horizontal line on the wall at the desired height.
2. The horizontal distance between the mounting holes must be exactly 330 mm.
3. Drill the mounting holes using a 6 mm drill bit. The depth of the holes must be at least 26 mm.
4. Insert the provided anchors into the holes until they are flush with the wall.
5. Screw in the two provided screws, ensuring at least 1 cm space between the wall and the screw head.
6. Place the heater onto the two screws (Position A) and slide the unit right and then down until a stable attachment is found (Position B).
7. Before connecting to the power supply, ensure all switches are off.

How to Use the Device

The radiator can be turned on in two ways:

1. By using the start/stop button on the radiator.
2. By using the accessory remote control.

Turning Device On/Off

Ensure the main switch is in the correct position. Press the black button next to the switch to turn the device on. Heating will start, and the ambient temperature will be displayed. Press the same button again to turn off the heating. A 30-second countdown will appear on the display. Wait for the countdown to finish and the fan to stop before unplugging the appliance.

Heating Modes

Press the heating button to switch between modes: Low power (1000 W), High power (2000 W), or Fan mode.

Timer Function

You can program the product to turn off automatically. Each press of the timer button increases the remaining shut-off time by 1 hour (1H, 2H, 3H, up to 8H).

Temperature Setting

Press the temperature setting button, then use the + and – buttons to set the desired temperature (range: 18 – 45 °C). If the set temperature is 3 degrees higher than the ambient temperature, the device will automatically switch to high power. To save settings, press the "OK" button or wait 5 seconds after the LED flashes.

Open Window Detection

This function is available only during heating. If the appliance detects a sudden drop in ambient temperature, it assumes a window has been opened and suspends heating as it would be ineffective. The device will pause heating.

Date and Time Setting

After switching on, press the date setting button, then use the + and – buttons to set the current date (e.g., 01-07). Press OK to save.

After setting the date, the time setting interface will appear automatically. Use the + and – buttons to set the hour (0-23) and then the minute (0-59). Press OK to save.

Weekly Timer

You can choose from 6 preset timing options: P1, P2, P3, P4, P5, P6.

Remark: P6: time setting range is 00-24H; the start time should be earlier than the end time.

Clearing Settings

Clear Temperature Setting: Press the ?️ button, then press the ?️ button. If a high temperature was previously set, the appliance will continue heating in high power mode; if a lower temperature was set, it will continue heating in low power mode.

Clear Weekly Timer: In the setting mode, press the ?️ button to delete. If a high temperature was previously set, the appliance will continue heating in high power mode; if a lower temperature was set or no temperature was set, it will continue heating in low power mode.

Symbols

• Fan: ?️
• Low Performance (1000 W): ? 1000W
• High Performance (2000 W): ? 2000W
• Timer Function: ⏰
• Weekly Timer: ?⏰
• Temperature Setting: ?️
• Open Window Detection: ?

Overheating Protection

If the device detects a temperature of 51 °C, it will automatically disable itself.

Proper Disposal

(Valid in the European Union and other European countries participating in selective collection) According to Directive 2012/19/EU, electrical waste and appliances must not be disposed of with household waste. Old appliances should be taken to collection points to maximize raw material recycling, thereby reducing their impact on human health and the environment. The crossed-out wheeled-bin symbol ?️❌ indicates products requiring separate collection. Consumers should contact their local authorities for more information.