Homepage - NeutriketherCON® - Neutrik
User Guide for NEUTRIK models including: NE8FDPS-TOP Airtight Straight Feedthrough, NE8FDPS-TOP, Airtight Straight Feedthrough, Straight Feedthrough, Feedthrough
File Info : application/pdf, 3 Pages, 2.19MB
DocumentDocumentR PRODUCT MANUAL etherCON® TOP airtight NE8FDPS-TOP & NE8FDIS-TOP & NE8FDPU-TOP ! Example of etherCON TOP Unmated connection options NE8FDPS-TOP etherCON/RJ45 to straight RJ45 feedthrough, D-shape flange NE8FDPU-TOP etherCON/RJ45 to 90° angled RJ45 (upwards) feedthrough, D-shape flange. NE8FDIS-TOP etherCON/RJ45 to 2,54 mm box header 2x4 pin feedthrough, D-shape flange 1 Connector installation P IP 65 & IP 67 & airtightness Example (NE8FDPS-TOP) of preassembled Delivery. Panel thickness: (without airtightness) ³ 2.0 mm [0.08"] ³ 1.0 mm [0.04"] Panel thickness recommendation is based only on metal panels and may differ for other materials. A BDA 692 V2 Step 1: Combine connector parts A Combine flange and sealing cap ð Page 1 PRODUCT MANUAL - etherCON® TOP airtight chassis connector Equipment / Panel . Panel thickness: ³ 2.0 mm [³ 0.08"] B C 2x Screws Step 2: Assembly B Insert the receptacle from the front into the panel. C Position the screw and fasten it. Ø 3.2 [.126] 0,1 [0.004] A 12.0 [.472"] 24.0 [.945"] 90° 5.3 - 6.0 [.201 - 0.236"] D 2 Additional information A Panel Cutout (Rear Side) Rz £ 16 Ø 24.0 ±0.1 [.945 ±0.003"] A 9.5 [.374"] 19.0 [.748"] BDA 692 V2 D ATTENTION: Tightening torque MA = 80 - 100 Ncm NOTE: Lubricate sealing lip with silicon from time to time. B Recommended screw M3 stainless steel countersunk type ð Page 2 PRODUCT MANUAL - etherCON® TOP airtight chassis connector 3 Application and Safety Instructions A Assembly l When assembling and processing the product, ensure the use of appropriate personal protective equipment. l Neutrik components must only be assembled with designated and specified components. l Replacement parts are suitable only when used in combination with the designated components. The product's characteristics are guaranteed only in the intended combination. B Application l The product is exclusively intended for installation in electronic equipment or similar devices. l The product is not intended for use in medical applications. l The product is not intended for use in potentially explosive or flammable environments. C Operation l Before plugging in, check the contact area for dry surfaces. l Product surfaces may cause burns at elevated ambient temperatures. Ensure the use of appropriate protective equipment. l Neutrik products should only be combined with products from Neutrik Group brands. D Cleaning l Clean only with dry and lint-free materials or compressed air. l The product must not be cleaned while under load. The product may only be cleaned while it is not connected to any voltage and without the use of cleaning agents. E Damages l Handle products with care. l In case of visible damages, check the suitability of the product for use. i More Information on the website https://www.neutrik.com/en/products/audio/ethercon Document No.: BDA 692 V1 Date: 2025-01-23 Neutrik AG I LI-9494 Schaan www.neutrik.com Data subject to change without prior notice. © 2025 NEUTRIK®. NEUTRIK® are registered trademark of Neutrik AG. ALL RIGHTS RESERVED. A brand of the Neutrik Group