Sharp MultiSync ME Series Large Format Installation Guide

Contents

Product Description and Notes: Page 1

Rotation: Page 1

Ventilation Recommendations: Page 2

Display Dimensions: Pages 3-10

Optional Stand Dimensions: Page 11-12

Optional Wall Mount Dimensions: Page 13

Optional Speaker Dimensions: Page 14

Intel® Smart Display Module Integration: Page 15

Compute Module Integration: Page 16

Input Panel: Page 17

ASCII Commands: Page 18

PD Comms Tool: Page 18

Cable Connection: Page 19

Browser Control: Page 19

Product Description

Type: LCD Display

Resolution: 3840 x 2160

Aspect Ratio: 16:9

EMI: Class B

*Absolute Max refers to when the display is at full brightness with all slots active and volume at 100.

NOTES:

• This document is intended to be used as a reference guide to supply useful information for a design or installation. It is not intended to be a step-by-step procedure for installation.
• Any ceilings or walls must be strong enough to support the monitor and the installation must be in accordance with any local building codes. All mounts should make secure contact to wood studs.
• Distances are in inches, for millimeters multiply by 25.4. Distances may vary ±5%.

www.sharpusa.com

Rotation

If the display is to be used in portrait orientation, rotation needs to be counterclockwise.

Diagram Description: A graphic shows a display in portrait mode with the text 'ABCDEF' displayed. An arrow indicates a counterclockwise rotation. A power indicator light is also shown.

Ventilation Recommendations

Dimensions below are minimum recommended for proper ventilation.

Diagram Description: A diagram illustrates minimum ventilation clearances. A rectangular display is shown with arrows indicating required space. Minimum clearances of ≥100 mm are required on the left, right, top, and bottom sides of the display. A minimum clearance of ≥30 mm is shown for the rear of the display. The maximum ambient temperature is indicated as <40 °C.

NOTE: The above are recommendations in order to keep your display as cool as possible. If the distances are less than the 100mm, extra ventilation may be necessary. The ventilation space should not be covered or closed off at the front of the opening. If for some reason the opening needs to be covered, other means of ventilation will need to be incorporated into the design. Contact NEC for design review and recommendations.

Display Dimensions – ME431

Diagram Description: Technical drawings of the Sharp ME431 display. Front, side, and top views are provided with detailed measurements. Key dimensions include: Overall Width: 38.307 inches (973.0 mm), Overall Height: 22.096 inches (561.2 mm), Overall Depth: 2.466 inches (62.6 mm). Bezel width is 0.547 inches (13.9 mm). VESA mounting pattern is 200 x 200 mm (M6 x 4-hole). Locations for AC INLET, SDM-S SLOT, RPI CM4 SLOT, SDM-L SLOT, IR SENSOR, POWER LED, and CONTROL BUTTONS are indicated.

Display Dimensions – ME431 cont'd

Diagram Description: Rear view of the Sharp ME431 display showing mounting hole patterns and connector panel. The diagram indicates the terminal panel location and control buttons. A separate inset diagram illustrates proper screw length for mounting: NEC strongly recommends using size M6 screws (10-12mm + the thickness of the bracket and washers in length). The inset shows a unit, mounting bracket, washers, and screw, with labels for 'Gap', 'No thread', 'Thickness of bracket and washers', and points A, B, C, D for measurement.

Display Dimensions – ME501

Diagram Description: Technical drawings of the Sharp ME501 display. Front, side, and top views are provided with detailed measurements. Key dimensions include: Overall Width: 44.425 inches (1128.4 mm), Overall Height: 25.550 inches (649.0 mm), Overall Depth: 2.465 inches (62.6 mm). Bezel width is 0.586 inches (14.9 mm). VESA mounting pattern is 400 x 400 mm (M6 x 4-hole). Locations for AC INLET, SDM-S SLOT, RPI CM4 SLOT, SDM-L SLOT, IR SENSOR, POWER LED, and CONTROL BUTTONS are indicated.

Display Dimensions – ME501 cont'd

Diagram Description: Rear view of the Sharp ME501 display showing mounting hole patterns and connector panel. The diagram indicates the terminal panel location and control buttons. A separate inset diagram illustrates proper screw length for mounting: NEC strongly recommends using size M6 screws (10-12mm + the thickness of the bracket and washers in length). The inset shows a unit, mounting bracket, washers, and screw, with labels for 'Gap', 'No thread', 'Thickness of bracket and washers', and points A, B, C, D for measurement.

Display Dimensions – ME551

Diagram Description: Technical drawings of the Sharp ME551 display. Front, side, and top views are provided with detailed measurements. Key dimensions include: Overall Width: 48.891 inches (1241.8 mm), Overall Height: 28.055 inches (712.6 mm), Overall Depth: 2.466 inches (62.6 mm). Bezel width is 0.547 inches (13.9 mm). VESA mounting pattern is 400 x 400 mm (M6 x 4-hole). Locations for AC INLET, SDM-S SLOT, RPI CM4 SLOT, SDM-L SLOT, IR SENSOR, POWER LED, and CONTROL BUTTONS are indicated.

Display Dimensions – ME551 cont'd

Diagram Description: Rear view of the Sharp ME551 display showing mounting hole patterns and connector panel. The diagram indicates the terminal panel location and control buttons. A separate inset diagram illustrates proper screw length for mounting: NEC strongly recommends using size M6 screws (10-12mm + the thickness of the bracket and washers in length). The inset shows a unit, mounting bracket, washers, and screw, with labels for 'Gap', 'No thread', 'Thickness of bracket and washers', and points A, B, C, D for measurement.

Display Dimensions – ME651

Diagram Description: Technical drawings of the Sharp ME651 display. Front, side, and top views are provided with detailed measurements. Key dimensions include: Overall Width: 57.571 inches (1462.3 mm), Overall Height: 32.966 inches (837.3 mm), Overall Depth: 2.679 inches (817 mm). Bezel width is 0.587 inches (14.9 mm). VESA mounting pattern is 400 x 400 mm (M8 x 4-hole). Locations for AC INLET, SDM-S SLOT, RPI CM4 SLOT, SDM-L SLOT, IR SENSOR, POWER LED, and CONTROL BUTTONS are indicated.

Display Dimensions – ME651 cont'd

Diagram Description: Rear view of the Sharp ME651 display showing mounting hole patterns and connector panel. The diagram indicates the terminal panel location and control buttons. A separate inset diagram illustrates proper screw length for mounting: NEC strongly recommends using size M8 screws (16-18mm + the thickness of the bracket and washers in length). The inset shows a unit, mounting bracket, washers, and screw, with labels for 'Gap', 'No thread', 'Thickness of bracket and washers', and points A, B, C, D for measurement.

Installing and Removing the Optional Table Top Stand

The ME431, M501 and M551 use the ST-401 or ST-43M. The ME651 utilizes the ST-65M.

Only use the screws that are included with the optional stand. The ST-65M will need included stand holders to also be attached.

• ME431: ST-43M (screws are included)
• ME501: ST-401 or ST-43M (screws are included)
• ME551: ST-401 or ST-43M (screws are included)
• ME651: ST-65M (thumbscrews, screws, and stand holders are included)

Diagram Description: Illustrations show the process of attaching an optional stand holder to the display. For ME431/ME501/ME551, the diagram shows attaching the stand to the display using screws and a soft cloth placed under the display. Dimensions for stand placement are indicated: 200 mm (ME431) and 400 mm (ME501/ME551).

Table Top Stand Dimensions (ST-401 pictured below):

Diagram Description: Technical drawings of the ST-401 table top stand. Front and side views are provided with measurements. Key dimensions include a height of 13.429 inches and a base width of 16.733 inches. The stand has a pole structure with mounting holes.

Table Top Stand Dimensions (ST-65M)

Diagram Description: Technical drawings of the ST-65M table top stand. Top, front, and side views are provided with measurements. Key dimensions include a base length of 15.741 inches. Note: The stand holder is included when the stand is purchased but is not shown in the drawing.

Optional Large Wall Mount (WMK-6598)

Diagram Description: Technical drawings of the WMK-6598 optional large wall mount. Multiple views (front, side, top) are provided with detailed measurements for the mount's dimensions and VESA compatibility. Key dimensions include widths of 17.50 inches and 19.85 inches, and heights of 15.75 inches and 16.58 inches. The mount features adjustable arms and locking mechanisms.

Optional Speaker Dimensions (SP-RM3a)

Diagram Description: Technical drawings of the SP-RM3a optional speaker. Multiple views (front, side, top) are provided with detailed measurements. Key dimensions include a height of 356.20 mm (14.02 inches) and a width of 65.75 mm (2.59 inches).

Intel® Smart Display Module Integration

1. Place the monitor face down on a flat even surface that is larger than the monitor screen. Use a sturdy table that can easily support the weight of the monitor. To avoid scratching the LCD panel, always place a soft cloth, such as a blanket that is larger than the monitor's screen area, on the table before laying the monitor face down. Make sure there is nothing on the table that can damage the monitor.
2. Remove the SLOT COVER and the OPTION COVER. Note when using Intel® SDM-L type option board, slide the CENTER RAIL to the right and remove. Reverse the process to re-attach.
3. Gently push in SDM-S or SDM-L module.
4. Attach included Option Cover after installation of SDM device.

Diagram Description: A series of illustrations show the steps for integrating an Intel® SDM module. The process involves removing covers, sliding a center rail (for SDM-L), inserting the SDM module (SDM-S or SDM-L), and re-attaching the option cover.

Compute Module Integration

Please see separate DS1-IF20CE installation guide for full integration. Image below may not represent actual back of unit but the concept is the same.

Removing the OPTION COVER is necessary for installation.

Diagram Description: An illustration shows the back of a display with a compute module (RPI CM4) installed in a slot. The diagram depicts the final installed state after the option cover has been removed and the module inserted.

Input Panel

Bottom:

Diagram Description: An image shows the bottom input panel of the display. Ports visible include USB, HDMI 1, HDMI 2, LAN, AUDIO, and REMOTE.

Side (Rotated):

Diagram Description: An image shows the side input panel of the display. Ports visible include RS-232C and a slot for an optional module. Labels indicate 'TOP' and 'BOTTOM' for orientation.

ASCII Common Commands

This monitor supports common ASCII control commands with many other NEC projectors. For more information on this, please see our website.

PD Comms Tool

Please download PD Comms Tool and open the Communications Log by going to View → Communications Log. From here you can find any external control code necessary for your installation.

PD Comms Tool can be downloaded from here: https://www.sharpnecdisplays.us/faqs/pdcommstool/179

Diagram Description: Screenshots of the NEC PD Comms Tool software are displayed, showing the interface for controlling and monitoring the display, including a communications log with sent and received messages.

Cable Connection

Communication Protocol:

• Interface: RS-232C
• Communication System: Asynchronous
• Baud Rate: 9600 bps
• Data Length: 8 bits
• Parity: None
• Stop Bit: 1 bit
• Communication Code: ASCII

Diagram Description: A diagram shows the RS-232C connector pinout for connecting to a PC, indicating connections for TxD, RxD, GND, RTS, and CTS.

Interface: Ethernet (CSMA/CD)

Communication System: TCP/IP (Internet Protocol Suite)

Communication Layer: Transport layer (TCP)

IP Address: 192.168.0.10 (default out of box)

Port Number: 7142 (Fixed)

Diagram Description: A diagram shows the Ethernet connector pinout, illustrating transmit and receive data lines (positive and negative) and indicating unused pins.

Browser Control

Information and control can also be available through the HTTP browser control menu.

In order to accomplish this, type: http://<the Monitor's IP address>/pd_index.html

Note that the LAN Power needs to be turned on in order for the display to be controlled while the units are off. All displays are set to the IP address 192.168.0.10 out of the box unless changed through the initial setup guide. Communicating network PC needs to be on the same subnet as display that is being communicated with.

Diagram Description: A screenshot of the web interface for the display is shown, with navigation menus on the left for various settings like 'HOME', 'REMOTE CONTROL', 'PICTURE', 'AUDIO', 'SCHEDULE', 'MONITOR INFORMATION', 'FIRMWARE VERSION', and 'ETHERNET'. It displays model name, serial number, firmware versions, and network settings like MAC address and IP address.