Ceiling Fan Light User Manual

WARNING!!!

To avoid fire, shock and serious personal injury, follow these instructions:

1. Read your user manual and safety information before installing your new fan. Review the accompanying assembly diagrams.
2. Before servicing or cleaning the unit, switch off the power at the service panel and lock the service panel to prevent accidental power activation. If the service disconnecting means cannot be locked, securely attach a warning device, such as a tag, to the service panel.
3. Exercise caution around the fan and its blades when cleaning, repairing, or working near the fan. Always turn off the power to the ceiling fan before performing any maintenance.
4. Do not insert any objects into the fan blades while the fan is in operation.
5. This appliance is not intended for use by young children or individuals with disabilities without supervision. Young children should be supervised to ensure they do not play with the appliance.
6. Before installing your ceiling fan, refer to the section on the proper wiring method for your fan. If you feel that you lack sufficient knowledge or experience in wiring, it is recommended to have a licensed electrician install your fan.

Before Installation

This manual is designed to make it as easy as possible for you to assemble, install, operate and maintain your ceiling fan.

NOTE: Place the parts from the loose fan parts bags in a small container to keep them from being lost. If any parts are missing contact us.

Tools Required:

• Ladder
• Screwdriver
• Wire Strippers
• Tape
• Goggles

Accessories

Check to see that you have received the following parts:

• 3 Wire nut (A)
• 2 Expansion screw (B)
• 2 Outlet box screw (C)
• 4 Washers (D)
• 1 Balance kit (E)
• 7 Blade screw (F)
• 4 Self-tapping screw (G)
• 1 Canopy screw(spare) (H)

Package Contents

Check to see that you have received the following parts:

• 1 Mounting bracket (a)
• 1 Receiver (b)
• 1 Canopy housing (c)
• 3 Fan blade (d)
• 1 Lamp body (e)
• 1 Lamp cover (f)
• 1 Remote controller (g)
• 1 Remote Controller Bracket (h)
• 1 Safety rope (Pre-installed) (i)

Energy Saving Usage

Ceiling fan performance and energy savings rely heavily on the proper installation and use of the ceiling fan. Here are a few tips to ensure efficient product performance.

Choosing the Appropriate Mounting Location

Ceiling fans should be installed or mounted in the middle of the room and positioned at least 7 feet above the floor and 18 inches away from the walls. If the ceiling height allows, it is recommended to install the fan 7~9 feet above the floor to achieve optimal airflow.

Turn Off When Not in the Room

If the room is unoccupied, turn off the ceiling fan to save energy.

Using the Ceiling Fan Year Round

Summer Season: Use the ceiling fan in the counterclockwise direction. The airflow created by the ceiling fan produces a wind-chill effect, making you feel cooler. Select a fan speed that provides a comfortable breeze; lower speeds consume less energy.

Winter Season: Reverse the motor and operate the ceiling fan at a low speed in the clockwise direction. This produces a gentle updraft, which pushes the warm air near the ceiling down into the occupied space. Remember to adjust your thermostat when using your ceiling fan. This simple step can lead to additional energy and cost savings.

Electrical and Structural Requirements

Your new ceiling fan will require a grounded electrical supply line of AC 110-130V/60Hz and a 15 Amp circuit. According to electrical codes, it is necessary to use a fan-rated outlet box to support the additional weight and motion associated with a ceiling fan. A fan-rated box will be clearly labeled as such and is typically designed to support ceiling fans weighing up to 70 pounds.

Fan-rated outlet boxes are available in various ratings and designs. It is essential to ensure that the rating of your ceiling fan outlet box meets the requirements for the specific ceiling fan you are installing. Please refer to the figures below for different structural configurations that can be used for mounting the outlet box.

• Low-profile use (Figure 1): A 1/2-deep pancake box is meant to be screwed to a joist or block. It is used if only one cable is coming into the box. It is also available in a saddle-mount configuration.
• Deep-profile use (Figure 2): A 2-1/4" deep box can be attached to blocking between joists and is roomy enough to handle more than one cable.
• Brace use (Figure 3): Paired with a deep box, this hanger is meant to span between two joists and takes the place of wooden blocking.
• If your fan is to replace an existing light fixture, turn power off at the main fuse box and remove the existing light fixture.

Diagram Description:

• Figure 1: Shows a low-profile pancake box mounted to a ceiling joist for a single cable.
• Figure 2: Shows a deep-profile box mounted between ceiling joists, accommodating multiple cables.
• Figure 3: Shows a brace used with a deep box, spanning between two ceiling joists.

WARNING

To ensure safety and prevent potential electrical shock, it is not sufficient to simply turn off the wall switch. Prior to wiring, make sure to turn off the electricity at the main fuse box. All wiring should be done in accordance with national and local electrical codes. Additionally, it is important to properly ground the ceiling fan as a precautionary measure against possible electrical shock. Following these guidelines will help ensure the safe installation and operation of your ceiling fan.

WARNING

Do not use a variable (rheostat) wall controller or dimmer switch to operate this fan. Doing so can cause damage to the ceiling fan's remote control unit. It is recommended to only use the provided remote control.

Installation

• Take out the mounting bracket from canopy housing. Loosen the two screws and rotate to remove from the canopy housing.
• Mount the bracket to the ceiling and use appropriate accessory screws to secure it based on the type of ceiling material.
  • Cement ceiling: Drill hole on the cement ceiling, then use expansion screws or expansion tube and self-tapping screw to fix.
  • Wood ceiling: Use self-tapping screws to drive into the wooden ceiling.
  • Junction box: If securing the bracket to an outlet box, use junction box screws.
• Use the safety rope to hang the ceiling fan to the bracket.
• Connect the wires between the controller and the fan motor: connect the 3-pin motor wire connector and the 2-pin lamp wire terminal.
• Connect the “Neutral wire” (white wire) from the ceiling to the white wire. Connect the “Live wire” (black wire) from the ceiling to the black wire. Connect the “Ground wire” (green or yellow/green or bare) from the ceiling to the green wire (housing/receiver/bracket).
• Fix the canopy housing's L slot to the bracket screws, and then rotate the fan canopy to ensure it is in certain location.
• Lock the other 2 screws and ensure that the 4 screws are tightened.
• Secure all three fan blades using six screws.
• Remove three screws from the triangular plate on the fan motor host.
• Push the lamp body upward and secure it by using the screws that were just removed from the triangular plate. Ensure that all three screws are tightened.
• Connect the wire terminal of the LED.
• Rotate the lamp shade upward to secure.
• Complete installation.

Operate Your Ceiling Fan

IMPORTANT: Using a full range dimmer switch to control fan speed will damage the fan. To reduce the risk of fire or electrical shock, do not use a full range dimmer switch to control the fan speed. (Figure 1).

Only control light on/off via wall fan switch.

Restore electrical power to the outlet box by turning the electricity on at the main fuse box. (Figure 2).

Diagram Description:

• Figure 1: Shows a wall with multiple light switches, one of which has a red 'X' over it, indicating a dimmer switch should not be used.
• Figure 2: Shows an open electrical panel labeled "MAIN FUSE BOX" with several circuit breakers.

Installation Recommended

Room Size:

UP TO 15 ft x 15 ft

Room Height:

Installation Height:

• 7FT
• 8FT
• 9FT
• 10FT

Remote Control

To operate the fan, please install 2 AAA batteries (included) in the handheld remote transmitter. If not used for extended periods of time, remove the batteries to prevent damage to the transmitter. Store the remote away from excessive temperatures and humidity.

Pairing:

1. Turn off wall switch for 1 minute
2. Turn on wall switch
3. Long-press ⏱️ within 5 seconds of step 2.

Wall Plate Installation:

Attach wall plate using the two screws provided.

Trouble shooting

Customer Service:

30-Days Full Refund Guarantee

If you are not completely satisfied or the item isn't what you expected, just tell us within 30 days. We will give you a full refund unconditionally.

Friendly Reminder

It's better to contact us than leaving a negative shopping experience. Nothing is more important than your satisfaction, and we will do our best to serve you.

Quick Response within 12 Hours

You can contact us without any hesitation at any time of the day, and we will reply to you within 12 hours. (It would be appreciated if you could provide us with a video or pictures, if available)

2-year Warranty

We will send you brand new items for free or give you a full refund if any quality problems occur within 2 years from the date of purchase.

Contact Information:

✉️ You can contact us by sending an email to support@fanlamppro.com