TV Table

Using an electric drill can speed up installation, but it requires reducing the torque of the drill. Product assembly can only begin after both the TV cabinet and fireplace have been received.

Important Information

Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.

Safety & Assembly Tips

Avoid Scratches

In order to avoid scratching, this furniture should be assembled on a soft layer, such as a rug.

Improve Efficiency

Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

Anti-Tipple Warning

Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.

Important Maintenance Note

It is important that any product assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months to assure stability throughout the lifespan of the product. For regular maintenance and cleaning of the frame, please use a rag dipped in neutral detergent, wipe it fully, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.

Board Identification

An exploded view showing various wooden panels labeled with numbers 1 through 16.

Parts List

• Part 1: Top panel
• Part 2: Front decorative trim
• Part 3: Side support panel
• Part 4: Side panel (x2)
• Part 5: Shelf support
• Part 6: Main body panel
• Part 7: Bottom panel
• Part 8: Left side cabinet panel
• Part 9: Right side cabinet panel
• Part 10: Middle vertical divider
• Part 11: Middle horizontal shelf
• Part 12: Drawer/door runner (x2)
• Part 13: Base support (x2)
• Part 14: Cabinet door (x2)
• Part 15: Back panel (x2)
• Part 16: Fireplace housing panel

Hardware and Tools Required

Tools

• Screwdriver (Phillips and flathead)
• Measuring tape
• Pencil
• Spirit level
• Electric drill (use with caution, reducing torque)

Hardware

• A: Cam lock screw, Ø 15 x 11.5 mm (x38)
• B: Cam bolt, Ø 7 x 40 mm (x38)
• C: Wooden dowel, Ø 8 x 40 mm (x31)
• D: Screw, Ø 3.5 x 14 mm (x24)
• E: Screw, Ø 4 x 25 mm (x12)
• F: Bracket (x6)
• G: Hinge (x4)
• H: Screw, Ø 5 x 40 mm (x26)
• I: Power cord adapter/connector (x1)
• J: Back panel buckle (J-1, J-2) (x16)
• K: LED light strip (x1)
• L: Crystal ornament (x8)
• M: Screw, Ø 3.5 x 18 mm (x8)
• N: Power outlet module (x2)
• Spare Bag: Contains 2 extra parts

Assembly Instructions

Step 1

Prepare panels 1, 2, and 3 by inserting cam bolts (B) and dowels (C) into their designated holes. Assemble these panels together.

To prevent bulging caused by the expansion of cam bolts installed on the edge of the wooden board, please orient the opening of the plastic particles towards the edge, allowing them to expand towards the solid part of the board.

Hardware: B x 26, C x 4

Step 2

Attach cam lock screws (A) and the LED strip (K) to panel 3. Attach cam lock screws (A) to panels 2 and 5. Attach panel 4 to panel 3 and panel 2 using cam lock screws (A). Connect the LED strip (K) to its power interface. Ensure the large hole faces upwards.

Hardware: A x 12, K x 1

Step 3

Insert cam lock screws (A) into panels 1, 2, 3, and 4. Attach the power outlet module (N) and connector (I) to panel 1. Rotate panel 1 by 180 degrees.

Hardware: A x 14, N x 2, I x 1

Step 4

Insert dowels (C) into panels 1, 2, and 3. Attach panel 6 to panels 1, 2, and 3 using dowels (C) and screws (H).

Hardware: C x 7, H x 14

Step 5

Before attaching the fireplace to the TV stand, unscrew four silver screws on both sides of the fireplace. Carefully remove the front glass and place it on a soft, clean surface. Attach panel 12 to the sides of the fireplace unit using screws (M). Place the crystal ornaments in the fireplace.

Hardware: M x 4

Step 6

Prepare panel 6 by inserting cam bolts (B) and dowels (C) into the designated holes.

To prevent bulging caused by the expansion of cam bolts installed on the edge of the wooden board, please orient the opening of the plastic particles towards the edge, allowing them to expand towards the solid part of the board.

Hardware: B x 12, C x 10

Step 7

Attach cam lock screws (A) to panel 12. Attach panel 12 to panel 6 using cam lock screws (A).

The installation of the fireplace requires two people to complete it together.

Hardware: A x 4

Step 8

Insert cam lock screws (A) into panels 8, 9, 10, and 11. Attach these panels to the main structure (panel 6) using the cam lock screws (A).

Hardware: A x 8

Step 9

Slide the back panels (15) into the grooves of the cabinet structure (panels 8, 9, 10, 11, 16). Connect the light strip interface to the power interface on the fireplace.

Step 10

Insert dowels (C) into panel 10. Attach base supports (13) to the bottom panel (7) using screws (M). Attach the fireplace housing panel (16) to the cabinet structure (panels 8, 9, 10, 11) using dowels (C) and screws (M).

Hardware: C x 10, M x 4

Step 11

Attach the bottom panel (7) to the main structure (panels 8, 9, 10, 11, 15, 16) using screws (H).

Note: When there is a gap between the wooden board (16) and the wooden board (7), you can use your fingers to hook this hole and shake it.

Hardware: H x 12

Step 12

Attach brackets (F) to the bottom panel (7) using screws (E).

Do not apply excessive force when rotating the screw.

Hardware: E x 12, F x 6

Step 13

Attach back plate buckles (J-1 and J-2) to the back panels (15) and the main structure to secure the back panels.

Do not lift the panel to move the product.

If the hardware J is not installed, it will cause the product to shake. Be sure to install back plate buckles as required.

Hardware: J x 16

Step 14

Place the crystal ornaments (L) into the fireplace.

Hardware: L x 8

Step 15

Attach hinges (G) to the cabinet doors (14) using screws (D). Attach the other part of the hinges (G) to the cabinet body (panels 7, 8, 9) using screws (D).

Hardware: D x 24, G x 4

Step 16

Adjusting Hinges

To adjust the vertical height:

Loosen the four screws 'A' on both hinges. Two of them are usually in slotted holes, which allows you to adjust up or down by a few mm. Then tighten back up.

To adjust depth:

Loosen screw 'B' and adjust the door. If the door cannot be adjusted, please loosen screw 'C', then try again. Tighten screws 'B' and 'C'.

To adjust side ways:

Turn the screw 'C' on BOTH hinges on each door.