User Manual for Bokang models including: 2BEX4-DK-38AB-1, 2BEX4DK38AB1, DK-38AB-1 Treadmill Walking Pad, DK-38AB-1, Treadmill Walking Pad, Walking Pad, Pad
Bokang Technology Co., LTD DK-38AB-1 Electric Treadmill 2BEX4-DK-38AB-1 2BEX4DK38AB1 dk 38ab 1
File Info : application/pdf, 15 Pages, 3.15MB
DocumentDocumentTREADMILL USER MANUAL CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Product parameters Main technical parameters Name Treadmill Walking Pad Model DK-38AB-1 Rated voltage AC110V/50HZ Net weight 17KG/37LBS Motor horsepower 3.0HP Gross weight 19.5KG/42LBS Plug type US Plug Expand size 1200X505X105MM /47.2X20X4.1IN Speed adjustment 0.5-3.7/MPH Max load-bearing 120KG/265LBS range Packing List NO. Name Qty NO. Name Qty Accessory 1 Host 1 piece 2 1 set Pack ACCESSORIES LIST NO. Name Quantity NO. Name Quantity 1 1 set Instructions Small 2 1 piece T-wrench Reminder: The product size, net weight, and gross weight provided are approximate values. For specific size and weight information, please refer to the actual product. Installation steps Step one (lift the treadmill out of the carton) Open the carton,take out the foam,and lift the machine out of the carton.(Figure 1) Figure-1 Important Precautions 1. Carefully read the user manual before using the product. 2. The product must be grounded properly when connected to the power supply. Failure to do so may result in electric shock. 3. In case of an emergency while running, unplug the safety key to stop the treadmill. 4. The safety key is a pull-wire type that must be inserted into the treadmill and its another end should be clipped to the waist to prevent injuries caused by sudden accidents. The treadmill cannot be started without the safety key inserted. Please remove it when not in use and keep it out of reach of children. 5. Do not replace or modify any parts of the treadmill to ensure safety. 6. Use the treadmill normally according to the user manual and do not remove any parts to avoid injury, such as the motor cover or the rear roller cover. 7. Do not touch the moving parts while the treadmill is in operation and keep children away from it. 8. Exercise moderately to avoid health damage. Stop exercising immediately if you feel dizzy. 9. Wait for the running belt to stop before folding it. 10. If the power cord is damaged, replace it with the help of the manufacturer, its service department, or a professional worker to avoid danger. 11.This product is only suitable for adults in good physical and mental condition. Please do not let children use it. FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This Equipment generates,uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However,there is no guarantee that interference will not occur in a Particular installation.If thise quipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IC Statement: This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. How to Use the Treadmill Before using the treadmill, please ensure that it has been properly unfolded as per the Product Installation Instructions. To quickly use the treadmill, please follow these steps: 1. Connect the power to the treadmill. 2. Press the "Start/Stop" button on the remote controller to start the treadmill, and the LED monitor will display "3-2-1", with the buzzer sounding once for every count down. After this, the motor will start running. 3. Once the treadmill is running, you can use the remote controller's "speed +" and "speed -" keys to adjust the speed according to your needs. The data on the LED monitor will automatically cycle and display every 5 seconds while the treadmill is in use. 4. To stop the treadmill, press the "Start/Stop" button on the remote controller. In case of an emergency, pull the safety key to immediately stop the treadmill. LED Monitor Instruction The LED window on the treadmill displays the following functions: 1. The time window displays the running time, with a range of 0.00-999. 9 The time indicator will be on when the unit (minute) displays the time. 2. The distance window displays the running distance data, with a range of 0.00-9999 The distance indicator will light up when the unit (miles) displays the distance. 3. The calorie window displays the calorie data, with a range of 0-999. The calorie light will be on when the calorie is displayed. Calorie calculation formula: 70×1.6V(mi/h)×t(h). The calories consumed per mile run is 112 kcal. 4. The speed window displays the running speed, with a range of 0.5-3.7MPH. The speed indicator will light up when the speed is displayed. Description of Remote Control Buttons Remote control function buttons: power, start/stop, mode, speed increase and decrease. The "Power" button is used to turn off the treadmill when it is running. When the treadmill is in standby mode, pressing this button will turn off the display and enter sleep mode. The "Start/Stop" button is used to start or stop the treadmill. When the power is turned on, pressing this button in the stop state will start the treadmill. Pressing the button when the treadmill is running will stop the treadmill. The "Mode" button is used to select the countdown mode for time, distance or calorie, as well as a free mode. Pressing this button will cycle through the options of "30:00" (time countdown mode), "1.0" (distance countdown mode), "50.0" (calorie countdown mode), and "0.0" (free mode). The "Speed +" button is used to increase the speed of the treadmill after it is started. After a single press, the speed will be adjusted by 0.1MI/H. When the button is pressed continuously for more than 1 second, the speed will continue to increase. The "Speed -" button is used to decrease the speed of the treadmill after it is started. After a single press, the speed will be adjusted by 0.1MI/H. When the button is pressed continuously for more than 1 second, the speed will continue to decrease. Suggested Stretches 1. Stretch Down Bend your knees slightly, and slowly bend your body down, letting your back and shoulders relax and try to touch your toes with your hands. Hold for 10-15 seconds, then relax. Repeat 3 times ( picture 1) 2. Hamstring Stretch Sit on a clean seat cushion and straighten one leg. Put the other leg in so that it fits against the inside of the straightened leg. Measure with your hands and touch your toes as much as possible. Hold for 10-15 seconds, then relax. Repeat 3 times for each leg. ( picture 2) 3. Calf and Achilles Tendon Stretches Stand with two hands against a wall or tree, one foot behind. Keep your hind legs upright and land on your heels and lean toward the wall or tree. Hold for 10-15 seconds, then relax. Repeat 3 times for each leg. (Picture 3) 4. Ankle Stretch Hold the balance with your left hand against the wall or table, then stretch your right hand back. Grab the toe of your right toe and slowly pull toward your buttocks until you feel the muscles on the face are very tense. Hold for 10-15 seconds, then relax. Repeat 3 times for each leg.( Picture 4) 5. Stretch Sartorius (inner thigh muscle) Sit with your feet facing each other and your knees facing out. Grab both feet with both hands toward the abdomen and pull in the direction of the ditch. Hold for 10-15 seconds, then relax. Repeat 3 times for each leg (Picture 5) Warranty Information Welcome to using FOCUSFIT series products. Please note that our company is not responsible for any failures caused by incorrect installation, incorrect use, or replacement of parts, including resulting repair costs which are the responsibility of the customer. Please note that this product is intended for home use only, and our company is not responsible for any problems caused by commercial use. Troubleshooting and Maintenance Fault Code Treadmill not working Main reason No power Solution Plug in to get power Belt not running smoothly E01 E02 E03 Connection wire not work well A.Lubrication oil is less Check all connection wire Add some silicon oil B.Running belt is too tight The wire from computer to bottom control board didn't connected well IGBT breakdown or motor open circuit (DC brushless motor is over-voltage, under-voltage) Speed sensor fail Loosen running belt 1. If communication between the electrical control and screen is obstructed, check each connection of the communication line from the screen to the lower control, ensuring that each wire is properly connected. 2. Check if there is any wire damage between the screen and controller, and replace the communication line if necessary. 1. Check if the power supply voltage is below 50% of the normal voltage, and retest using the correct voltage specifications. 2. Check if there is any abnormal odor coming from the controller, and replace it if necessary. 3. Check if the motor wires are properly connected, and reconnect if needed. 1. If no speed sensor signal is detected for 5-8 seconds, check whether the sensor plug is properly connected or damaged, and reconnect or replace the sensor accordingly. 2. Check if there is any abnormal odor coming from the controller, and replace it if necessary. 3. If there is no motor input signal detected for 5-8 seconds, check whether the motor wires are properly connected or if the motor is defective. 1. The system may be drawing excessive current due to the load being over the rated capacity, triggering the protective shutdown. The system can be restarted after a complete shutdown. 2. If a certain part of the treadmill becomes stuck, it can cause the motor to be unable to rotate normally, resulting in excess load and current flow. This may trigger the system protection and shut down the system. To resolve this issue, the treadmill needs to be adjusted and once done, the system can be restarted for normal operation. E05 Over-current Protection 3. Inspect the motor for any signs of excessive noise or a burning smell during operation. If such signs are present, it may indicate a faulty motor that needs to be replaced. 4. Check if there is any burnt smell coming from the components of the controller. If any components show signs of damage, it may indicate a faulty controller that needs to be replaced. 5. Inspect if the power supply voltage are incorrect or lower than required. Use the appropriate voltage and retest the machine. For DC brushless machines, also check if the motor wires are properly connected.. E07 or "--" E08 E09 E10 Safety key off Driver failure (internal self-test error 'driver overheating) Communication failure Motor open circuit 1. Simply plug in the safety key. 2. Check if the reed switch or contact blade and their connecting wires are damaged. 1. Wait for a period of time, then restart the power after it has cooled down. (Only applicable for brushless controllers.) 2. The controller is faulty. Replace the controller. If the lower-level controller is not receiving signals from the higher-level controller, replace the communication cable and check if the communication port is functioning properly. 1. Check whether the motor wires are properly connected, and reconnect if necessary. 2. Check if the motor brushes are stuck. Pl s add si l i con oi l t o t he hol e same as ar r ow shows