éç¾½èµè½¦-å¡ä¸è½¦-çµå¨å¡ä¸è½¦-å¿ç«¥å¡ä¸è½¦
Instruction Manual for ARROWY RACING models including: RMRC2025, RMRC2025 RaceMaster Kart Control System, RaceMaster Kart Control System, Kart Control System, Control System
Nanjing Arrowy Racing Technology Co., Ltd. RMRC2025 RaceMaster 2A49Z-RMRC2025 2A49ZRMRC2025 rmrc2025
File Info : application/pdf, 11 Pages, 854.07KB
DocumentDocumentRaceMaster Kart Control System Ver1.0 CONTENTS 01 RaceMaster.Remote Control -1 Remote Control Button Description -2 Remote Control Function Introduction and Operation Instructions 2.1 Kart Control 2.2 Kart Configuration 2.3 Remote Configuration 2.4 Remote Pairing 2.5 Language Settings 2.6 System Information 2.7 Device Control 02 RaceMaster.Transponder 03 Equipment -1 Flag Light -2 Start Light (Electronic Version Only) *Note: This manual provides detailed instructions for the RaceMaster Remote Control system. Charger Remote Control RaceMaster.Remote Control 1 1 Remote Control Button Description Gear Switching Scroll Up to Select Return Home Screen Display all accessible functions. The system defaults to the home screen upon startup. Speed Limit Gear Parking Gear Scroll Down to Select Function Selection Confirm 2 2 Remote Control Function Introduction and Operation Instructions 2.1 Kart Control Press the number key "1" to enter. Function Description There are two function options: single kart control and full track control. 01 Single Kart Control First, input the kart number to be controlled. Then, press the corresponding gear button (D1, D2, D3,L,STOP) to switch gears. 02 Full Track Control Press "#" briefly to switch to full track control mode. In this mode, press- ing the gear buttons (D1, D2, D3, L, STOP) to control all vehicles uniformly. Gear Switching Parking Gear Speed Limit Gear Clear Kart Number: Press "*" briefly to quickly clear the entered kart number. Exit: Press and hold the "*" key to return to the home screen. 2.2 Kart Configuration (Access this function by entering configuration mode - long press the transmitter button for 5 seconds) Press the number key "2" to enter. Function Description 3 There are two configuration options: reconfiguring the kart number and switching control modes. 01 Set Kart Number Press the number key "1" to enter. First, input the old kart number (must match the kart number entered in the kart control section), then press "#" to move to the next line. Input the new kart number (1 - 99), then press "#" to save and return to the kart configuration interface. 01 Configure Kart Number 02 Old Kart Number cPress '#' to line break 03 04 New Kart Number 02 Control Mode Press the number key "2" to enter. Input the kart number of the module you want to modify, then press "#" to move to the next line, and press "0" to switch the working mode (switch table control, remote control, mixed control). Finally, press the "#" key to confirm and return to the kart configuration interface. *Note: Keep the factory settings and do not modify them. Exit: Press the "*" key briefly to return to the home screen. 4 01 Control Mode 02 Target Kart Number 03 Work Mode (Default Switch Panel Control) switch table control 04 2.3 Remote Configuration Press the number key "3" to enter. Function Description Displays the current remote control address. Input a new address (1 - 65535) and press "#" to save. 01 Remote Configuration 02 Current Address (Default) 03 04 New Address *Note: After modifying the address, the remote will no longer control previously paired karts. When adding a new remote, set its address to match an existing remote's address to enable control. Exit: Press the "*" key briefly to return to the home screen. 2.4 Remote Pairing Press the number key "4" to enter. Function Description 5 1.Enter Pairing Mode: Long press the transmitter button for 5 seconds until the digital display flashes. 2.Request Pairing: Press any number key. 3.Clear Current Pairing: Press the "#" key briefly. 4.Clear Other Remote Pairings: Press and hold the "#" key. Exit: Press the "*" key briefly to return to the home screen. Transmitter Button Transponder *Note: For transponder - related content, please refer to the transponder manual. 2.5 Language Settings Press the number key "5" to enter. Function Description Press "0" to switch languages. Language Settings 0 Switch Language Exit: Press the "*" key briefly to return to the home screen. 2.6 System Information Press the number key "6" to enter. Function Description Displays hardware and software version information. Exit: Press the "*" key briefly to return to the home screen. 6 2.7 Device Control Press the number key "7" to enter. Function Description Mainly used for managing and operating specific devices. 01 Flag Light Press the number key "1" to enter. Directly press the number keys (1 - 9) to quickly switch between different flag light colors. For more than 9 colors, use the "Select Down" button to cycle through additional options. *Note: For flag light - related content, please refer to the flag light manual. Scroll Down to Select 02 Start Light Press the number key "2" to enter. Control the starting light with the numeric keypad. Press "1" for the start signal, "2" for red, "3" for black. Exit: Press the "*" key briefly to return to the home screen. 7 Nanjing ARROWY RACING Technology Co.Ltd. Web: www.arrowy.com.cn Tel: 400-8116-819 FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.