INKBIRD IHC-200 WIFI Humidity Controller

Part 1: Quick Guide to Use

01 CAUTION

ATTENTION:

• KEEP CHILDREN AWAY
• TO REDUCE THE RISK OF ELECTRIC SHOCK, USE ONLY INDOORS
• RISK OF ELECTRIC SHOCK. DO NOT PLUG INTO ANOTHER RELOCATABLE POWER TAPS OR AN EXTENSION CORD.
• USE ONLY IN DRY LOCATION

ATTENTION (French):

• ELOGIGANEZ LES ENFANTS
• Pour réduire le d'électrocution, Pour Usage À L'Intérieur Seulement.
• Risque de choc électrique. Ne pas brancher dans une autresource de courant portative ou une rallonge.
• UTILISER UNIQUEMENT DANS DES EMPLACEMENTS SECS

02 Specification

Model: IHC-200-WIFI

Brand name: INKBIRD

Input: 230V ac 50Hz 10A/2300W MAX

Output: 230V ac 50Hz 10A/2300W (total two receptacles) MAX

Disconnection means: Type 1B

Pollution degree: 2

Rated impulse voltage: 2500V

Automatic action: 30000 cycles

Humidity Probe

Humidity Measurement Range: 10~99%RH

Humidity Display Accuracy: 0.1%RH

Relative Humidity Accuracy (10% to 95%RH): Type: ±3%RH, Max: ±5%RH

Display Unit: %RH

Ambient

Ambient temperature: Room temperature

Storage environment: temperature:0°C~60°C/32°F~140°F; humidity: 20~80%RH (Unfrozen or condensation state)

Warranty

Controller: Two years warranty

Temperature and Humidity Probe: One year warranty

03 Technical Assistance and Warranty

3.1 Technical Assistance

For installation or usage problems, refer to the instruction manual. For further assistance, email support@inkbird.com. Replies are provided within 24 hours, Monday to Saturday. Visit the official website (www.inkbird.com) for common technical questions.

3.2 Warranty

INKBIRD TECH CO., LTD warrants this controller for one year (temperature probe) and two years (controller) against defects in workmanship or materials from the date of purchase, provided it is operated under normal conditions by the original purchaser (non-transferable). This warranty is limited to repair or replacement at INKBIRD's discretion.

Part 2: Wi-Fi Humidity Controller Manual

01 Introduction

The IHC-200 WIFI Humidity Controller features:

• PV (1): Displays current humidity in normal mode; displays menu code in setting mode.
• SV (2): Displays the setting humidity value in normal mode; displays the setting value in setting mode.
• Red Indicator Light (3): Indicates humidification output is ON (red) or OFF.
• Green Indicator Light (4/5): Indicates dehumidification output is ON (green) or OFF. Blinking green indicates dehumidification delay protection state.
• WORK1 (6): Humidification Output Socket.
• WORK2 (7): Dehumidification Output Socket.
• Buttons (8): Setting Button (SET), Increase Button (▲), Decrease Button (▼) for settings.

02 Product Features

• Plug-n-Play
• Dual Relay Output: Supports both humidifying and dehumidifying equipment simultaneously.
• Display Screens: Show set humidity value and measured humidity value concurrently.
• Support Humidity Calibration
• Support Dehumidification Control Delay Protection
• Settable High/Low Humidity Alarm
• Probe Fault Alarm
• Wi-Fi Smart App

03 Specifications

• Voltage: 100-230Vac 50/60Hz
• Current: 10A
• Maximum Power: 1200W(120Vac), 2200W(220Vac)
• Humidity Measurement Range: 10~99%RH
• Humidity Display Accuracy: 0.1%RH
• Relative Humidity Accuracy (10% to 95%RH): Typ: ±3%RH, Max: ±5%RH
• Display Unit: %RH
• Operating Ambient Temperature: -20℃~40℃/-4°F~104°F
• Storage Temperature: 0°C~60°C/32°F~140°F
• Storage Humidity: 20~80%RH (not frozen or dewed)
• Warranty: Controller: 2 years, Probe: 1 year

04 Wi-Fi Connection

4.1 Download INKBIRD App

Search for "INKBIRD" on the Appstore or Google Play to download the app. Alternatively, scan the provided QR code.

[QR code for INKBIRD APP download]

4.2 Connect to your phone

1. Register using the INKBIRD app by selecting your Country/Region and entering your email. A verification code will be sent to your mailbox for identity confirmation.
2. Press the "Add Home" button to create your home.
3. Tap "+" or "add device" on the home page to add the device.
4. To reset the WIFI, press and hold the [WIFI] button for 2 seconds. The controller enters Smartconfig configuration state by default. Short press the [WIFI] button to switch between Smartconfig and AP modes.

The WIFI module requires approximately 5 seconds for data processing to display the corresponding LED symbol and Wi-Fi status.

4.3 Quick Connection

1. Plug the device into the socket and ensure it is in Smartconfig state (LED symbol flashing rapidly, interval 250ms).
2. Check if the LED symbol is blinking rapidly and confirm on the app. Enter your Wi-Fi password and click "Confirm" to connect.

Note: The device supports only 2.4GHz Wi-Fi routers.

4.4 Connect the device in AP mode

1. Plug the device into the socket and ensure it is in AP Configuration State (LED symbol flashing slowly, interval 1500ms).
2. Click "Confirm indicator slowly blink" and select your Wi-Fi network. Enter the Wi-Fi password and click "Confirm" to proceed.
3. Press "Connect now" to access your smartphone's WLAN Setting interface. Select "SmartLife-XXXX" to connect directly to the router without a password.
4. Return to the app to enter the automatic connection interface.
5. Click "Done" after successful device addition to enter the device controlling interface.
6. In humidity control mode, users can configure control functions via the app.

4.5 Wi-Fi State

• Smartconfig State: Wi-Fi indicator light flashes rapidly (250ms interval).
• AP State: Wi-Fi indicator light flashes slowly (1500ms interval).
• Connection Fail State: Wi-Fi indicator light is off.
• Connection Succeed State: Wi-Fi indicator light remains on.

05 Settings

5.1 Key Setting

5.1.1 Factory Reset

Hold the [SET] button and turn on the device. A short beep indicates that all humidity probe parameters have been restored to factory settings.

5.1.2 Fast Setting

Press the [SET] button lightly to enter quick set-up mode. The SV screen displays the current setting value and flashes. Use the [▲] or [▼] buttons to change the value. Hold the [▲] or [▼] buttons to change the value rapidly. Press the [SET] button again to save settings and exit. Settings are also saved and the mode is exited if there is no operation for 10 seconds.

5.1.3 Normal Setting

Hold the [SET] button for 2 seconds to enter setting mode. The PV screen displays the menu code "HS" for the first item, and the SV screen displays the corresponding setting value. Press the [SET] button to switch between menu items. Use the [▲] or [▼] buttons to change the value. The value is saved automatically when switching to another menu item by pressing [SET].

Press and hold the [SET] button for 2 seconds to save settings and exit. The controller also exits setting mode and returns to normal working mode if there is no operation for 30 seconds.

5.2 Flowchart of the Settings

[Diagram showing the settings flowchart: Press SET for over 2 seconds to enter parameters setting mode. HS (Humidity Setting Value), HD (Humidification Difference Value), DD (Dehumidification Difference Value), AH (Alarm High Humidity Limit), AL (Alarm Low Humidity Limit), PT (Dehumidification Delay Time), CA (Humidity Calibration). Options to press SET or wait for 30 seconds to return to Working normally.]

5.3 Icons in this Manual

06 Basic Operations

6.1 Instructions for Humidity Control Setting (HS,HD,DD)

The PV Screen displays the current humidity. The device automatically recognizes and switches between humidification and dehumidification modes.

• Humidification: If measured Humidity(PV) ≤ Humidity Setting Value(HS) - Humidification Differential Value(HD), the equipment enters humidification state. The red LED turns on, and WORK1 output socket turns on. If measured Humidity(PV) ≥ Humidity Setting Value(HS), the red LED turns off, and WORK1 output socket turns off.
• Dehumidification: If measured Humidity(PV) ≥ Humidity Setting Value(HS) + Dehumidification Differential Value(DD), the equipment enters dehumidification state. The green LED turns on, and WORK2 output socket turns on. If the green LED blinks, it indicates the dehumidification delay protection state, and WORK2 output socket turns off. If measured Humidity(PV) ≤ Humidity Setting Value(HS), the green LED turns off, and WORK2 output socket turns off.

Example: HS=50.0%RH, HD=5.0%RH, DD=8.0%RH. If PV ≥ 58.0%RH (HS+DD), dehumidification starts (green LED ON, WORK2 ON). If PV ≤ 55.0%RH (HS), green LED OFF, WORK2 OFF. If PV ≤ 45.0%RH (HS-HD), humidification starts (red LED ON, WORK1 ON). If PV ≥ 50.0%RH (HS), red LED OFF, WORK1 OFF.

Note: When powering on or exiting the setting state, the differential values do not need to be judged. For example, if HS=50.0%RH, HD=5.0%RH, DD=8.0%RH: If PV > 50.0%RH (HS), dehumidification state is entered. When PV ≤ 50.0%RH (HS), dehumidification stops, returning to normal humidity control mode. If PV < 50.0%RH, humidification state is entered.

6.2 High/Low Humidity Alarm (AH,AL)

The equipment alarms if measured humidity (PV) ≥ high humidity alarm set value (AH). The PV screen displays the AH value and current humidity alternately, with a "bi-bi-Biii" buzzer sound until PV < AH. Pressing any button stops the alarm.

The equipment alarms if measured humidity (PV) ≤ low humidity alarm set value (AL). The PV screen displays the AL value and current humidity alternately, with a "bi-bi-Biii" buzzer sound until PV > AL. Pressing any button stops the alarm.

Note: The setting value of AL should be less than the setting value of AH.

6.3 Dehumidification Delay Time (PT)

The equipment will not start dehumidification immediately for the first time if the measured value is larger than the sum of the set humidity value and the dehumidification return difference. It will start dehumidifying after the set delay time.

The equipment dehumidifies immediately if the interval time between two adjacent dehumidifications is longer than the delay time.

The equipment dehumidifies after the delay time if the interval time between two adjacent dehumidifications is shorter than the delay time.

The delay time starts timing when the last dehumidification is completed.

Note: When powering on or exiting the setting state, the delay time does not need to be judged.

6.4 Humidity Calibration (CA)

If the measured humidity differs from the standard humidity, calibrate the device by adding or reducing a correction value to align the measured humidity with the standard humidity. Calibrated humidity = measured humidity value + calibration value.

07 Sensor Fault Alarm

If the humidity sensor has a short circuit or open circuit, the controller enters probe fault mode and stops running. The buzzer will alarm, and the screen will display "ER". Pressing any key stops the buzzer. The controller returns to normal working state when all malfunctions are resolved.

08 Important Safeguards

Take special care when using electrical appliances. Follow these safety tips:

• Read all instructions.
• Check that flexible leads and the appliance are in good condition.
• Check your plug sockets are not overloaded with too many electrical appliances to prevent overheating.
• Do not use the appliance for anything other than its intended use.
• Do not cut the cord or place it on hot surfaces.
• Do not place on or near a hot gas or electric burner, or in a heated oven.
• Do not attempt to clean or repair the appliance while it is still plugged in.
• Do not wrap flexible cables around the appliance when it is still warm.
• Switch off the device when not in use.
• Disconnect the power immediately if the device falls into water. The warranty does not cover water damage.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance. Close supervision is necessary when any appliance is used by or near children.

09 Warranty

This Limited Warranty applies only to the INKBIRD IHC-200-WIFI Humidity Controller.

What is Covered and for How Long

INKBIRD warrants that all new products are free from defects in manufacturing, materials, and workmanship for a period of one year from the date of retail purchase.

What this Warranty Does Not Cover

The warranty does not cover defects or malfunctions caused by misuse, abuse, improper maintenance, failure to follow operating instructions, or use with equipment for which it is not intended. The warranty also does not apply to damage caused by unauthorized alteration, modification, or repair of the product. INKBIRD does not warrant or provide service or support for any third-party products, including iPhones and Android Phones.

How to Obtain Warranty Service

To obtain warranty service for products purchased from a third-party, retail, or directly from INKBIRD, return the product with proof of purchase using the following procedures:

• Contact INKBIRD Customer Support for specific return and shipping instructions via email at support@inkbird.com. You may be asked to complete a warranty service request form. To ensure warranty claims are for INKBIRD products, the technical support department may require a copy of your purchase receipt.
• Label and ship the product, freight prepaid, to the address provided by INKBIRD.

Exclusions and Limitations

THIS WARRANTY IS YOUR EXCLUSIVE WARRANTY AND REPLACES ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AS SOME STATES OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF EXPRESS OR IMPLIED WARRANTIES, THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. IN THAT EVENT, SUCH WARRANTIES APPLY ONLY TO THE EXTENT AND FOR SUCH DURATION AS REQUIRED BY LAW AND ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. AS SOME STATES OR JURISDICTIONS DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, THE ABOVE LIMITATION ON DURATION MAY NOT APPLY TO YOU.

10 FCC Requirement

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

11 IC Warning

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure. Users can obtain Canadian information on RF exposure and compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

French Translation:

L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :

1. L'appareil ne doit pas produire de brouillage;
2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf.

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ouémetteur.

Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.

12 Troubleshooting Guide