User Manual for Jabra models including: VSM040, VTD040, VTD040 Panacast 50 Video Bar System, VTD040, Panacast 50 Video Bar System, Video Bar System, Bar System, System
1 sept. 2023 — Thank you for using the Jabra PanaCast 50 Video Bar System. We hope you will enjoy it! Here are some key features you will benefit from the Jabra PanaCast ...
PanaCast 50 Video Bar System UC VB & TC, EMEA - UCExperts
File Info : application/pdf, 36 Pages, 1.89MB
DocumentDocumentPANACAST 50 Video Bar System Technology for life's new rhythm USER MANUAL © 2023 GN Audio A/S. All rights reserved. Jabra® is a trademark of GN Audio A/S. The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by GN Audio A/S is under license. Made in China MODEL: VSM040; VTD040 Declaration of Conformity can be found on www.jabra.com/doc 1. Welcome........................................ 5 2. Overview........................................ 6 2.1 Jabra PanaCast 50 Video Bar System Base Unit overview 2.2 Jabra PanaCast Control overview 2.3 Included accessories - Jabra PanaCast 50 Video Bar System Base Unit 2.4 Included accessories - Jabra PanaCast Control 2.5 Optional accessories 3. Hardware setup overview ....... 13 4. Visual indicators......................... 15 5. Settings management.............. 16 6. Video settings............................. 18 6.1 Intelligent Zoom 6.2 Virtual Director 6.3 Panoramic View 6.4 Dynamic Composition Single Stream - only for MS Teams Rooms 6.5 Field of view 6.6 Pan, Tilt, Zoom presets - only for Zoom Rooms 6.7 Image quality settings 6.8 Video flicker 7. Share content ............................. 24 7.1 Wireless content sharing 7.2 Wired content sharing 8. Privacy cover............................... 26 9. Safety capacity settings........... 27 10.Update firmware........................ 28 11.Restart devices........................... 29 12.Factory reset .............................. 32 3 13.Support ........................................ 35 13.1FAQ and technical specifications 13.2How to care for your Jabra device 4 1. Welcome Thank you for using the Jabra PanaCast 50 Video Bar System. We hope you will enjoy it! Here are some key features you will benefit from the Jabra PanaCast 50 Video Bar System: · World-class audio with full duplex and powerful stereo speakers · Unique 180° full room coverage in high-definition Panoramic-4K for a more natural view of the meeting room · Access to an easier meeting experience with the touchscreen-activated PanaCast Control · Certified for the strict requirements of Microsoft Teams Rooms and Zoom Rooms to connect, share, and collaborate seamlessly and securely · On-device AI that powers a range of intelligent features for immersive and natural virtual collaboration 5 2. Overview 2.1 Jabra PanaCast 50 Video Bar System Base Unit overview FRONT SIDE Microphones Microphones Cameras Microphones Microphones Speakers LED Speakers 6 BACK SIDE Port connections HDMI IN HDMI OUT2 HDMI OUT1 USB A USB A Air vents Reset button ETHERNET USB C POWER 3.5MM JACK Adjustable mounting bracket 7 2.2 Jabra PanaCast Control overview FRONT SIDE 10-inch LCD touch screen BACK SIDE Ethernet port (PoE) USB-C port Ultrasonic sound proximity detector Port connections (remove cover for access) Proximity sensor Manual tightening Pinhole reset screws button 8 2.3 Included accessories - Jabra PanaCast 50 Video Bar System Base Unit AC power adapter (1.83m/6ft) AC power cable (1m/3.28ft) HDMI cable (1.83m/6ft) RJ45 Ethernet cable (4.57m/15ft) Wall mount Camera privacy cover Cable cover compartment (2 pcs) with embedded screws & screwdriver Additional accessories can be purchased at jabra.com/accessories 9 2.4 Included accessories - Jabra PanaCast Control Jabra PanaCast Control POWER OVER ETHERNET (PoE) KIT PoE injector AC power cable (1m/3.28ft) RJ45 Ethernet cable (2 pcs) (4.57m/15ft) Additional accessories can be purchased at jabra.com/accessories 10 2.5 Optional accessories Accessories can be purchased at jabra.com/accessories Screen mount Table stand 11 Accessories can be purchased at jabra.com/accessories Regional power cords(1m/3.28ft) HDMI cable (1.83m/6ft) HDMI ingest cable (4.57m/15ft) RJ45 Ethernet cable (4.57m/15ft) USB-A to C cable (4.57m/15ft) USB-A to B cable Jabra PanaCast Control (1.83m/6ft) table mount 12 3. Hardware setup overview This is an overview of the steps required to set up the Jabra PanaCast 50 Video Bar System. 1. Mount the video bar. Refer to the assembly videos or assembly instructions available in jabra.com/ help/panacast50vbs/getstarted 2. Connect the cables. Refer to the cabling instructions available in the Installation manual. 3. Set up the touch controller. After the device powers on, follow the setup wizard displayed on the touch controller. During the last step of the configuration, it is necessary to log into the video conferencing account of your service provider. 13 4. Manage settings and devices locally using the touch controller or remotely using the Web Console. To manage settings and devices using the touch controller, go to the More menu in the video conferencing app, select Settings and then Device settings. The Jabra PanaCast 50 Video Bar System settings screen will be displayed. Go to the Admin menu and log in as an administrator. If this is the first login, the default username is admin and the password is the last 6 digits of the touch controller serial number. To manage settings and devices using the Web Console, enter the IP address of the video bar or the touch controller in a browser. If this is the first time accessing the Web Console, the default username is admin and the password is the last 6 digits of the serial number of the device used to access the Web Console. To access the Jabra PanaCast 50 Video Bar System manuals, assembly videos and instructions, go to jabra.com/support or jabra.com/help/panacast50vbs/getstarted 14 4. Visual indicators LED STATUS Off or not streaming Starting up Connected In call or streaming video/media In call, audio muted Firmware updating (LED off) (flashing white) (on for 3 seconds) (flashing pink) 15 5. Settings management After the Jabra PanaCast 50 Video Bar System configuration process is completed, the touch controller will display the video conferencing app of your service provider. To access the Jabra PanaCast 50 Video Bar System settings, go to the More menu in the video conferencing app, select Settings and then Device settings. Basic settings and general information of the touch controller will be displayed. Advanced settings are available when logging in as an administrator. If this is the first login, the default username is admin and the password is the last 6 digits of the touch controller serial number. 16 All Jabra PanaCast 50 Video Bar System settings can be configured using the Web Console. To access the Web Console, enter the IP address of the video bar or touch controller in a browser. The IP address is displayed on the installation screen during the configuration process of the Jabra PanaCast 50 Video Bar System. The IP address is also available in the About section of the Device settings menu on the touch controller. If this is the first time accessing the Web Console, the default username is admin and the password is the last 6 digits of the serial number of the device used to access the Web Console. 17 6. Video settings Administrators can remotely configure the video conferencing settings using the Web Console or directly in the touch controller. To access the video conferencing settings using the touch controller, go to the More menu in the video conferencing app, select Settings and then Device settings. The Jabra PanaCast 50 Video Bar System settings screen will be displayed. Go to the Admin menu and log in as an administrator. To access the video conferencing settings using the Web Console, enter the IP address of the video bar or touch controller in a browser. The IP address is displayed on the installation screen during the configuration process of the Jabra PanaCast 50 Video Bar System. The IP address is also available in the About section of the Device settings menu on the touch controller. 18 6.1 Intelligent Zoom Intelligent Zoom is a camera mode that dynamically frames all visible people within 6 meters (20 feet). Only one camera mode can be active at a time. By default, camera mode is set to Intelligent Zoom. 6.2 Virtual Director Virtual Director is a camera mode that dynamically switches to and focuses on the person who is speaking. 6.3 Panoramic View Panoramic View is a camera mode that displays a panoramic view of the meeting room. 19 6.4 Dynamic Composition Single Stream - only for MS Teams Rooms Dynamic Composition Single Stream is an advanced camera mode that displays up to 4 participants in a meeting room in a tiled view. The tiled view will dynamically update to display the participants who are actively speaking. If this camera mode is selected, a reboot of the device is required. 20 6.5 Field of view The angle of the camera can be optically adjusted for a wider or narrower view of the meeting room. By default, Field of view is set to 180°. 6.6 Pan, Tilt, Zoom presets - only for Zoom Rooms Pan, Tilt, Zoom presets allow administrators to adjust and save the camera view using the touch controller. Saved presets do not overwrite the default Pan, Tilt, Zoom settings. Users can select saved presets when a new meeting starts. 21 6.7 Image quality settings The image brightness, contrast, saturation, sharpness, and white balance can be adjusted in the Web Console or using the touch controller through the admin device settings. Additionally, Vivid HDR and Automatic white balance can be enabled. If Vivid HDR is enabled, contrast, saturation, and sharpness cannot be adjusted manually. If Automatic white balance is enabled, the white balance cannot be adjusted manually. 22 6.8 Video flicker Video flicker can occur if the Jabra PanaCast 50 Video Bar System is not set to the correct geographical region. To prevent video flicker, select Auto (50Hz/60Hz) for regions that support NTSC format, or 50Hz for regions that support PAL format. By default, Video flicker is set to Auto. 23 7. Share content 7.1 Wireless content sharing The touch controller has both Bluetooth® technology and an ultrasonic emitter that allows users to share content directly from their computers or mobile devices. When sharing content using a wireless signal, the mobile device must be within 10 meters (32.8 feet) of the touch controller and the share content feature must be enabled in the video conferencing app. For more information on how to share content wirelessly, go to the support page of your video conferencing service provider. 24 7.2 Wired content sharing Connect an HDMI cable from the computer to the HDMI IN port on the back of the video bar. The content from the computer will be displayed in the meeting and on the room monitor connected to the video bar. Additional HDMI cables are not supplied and can be purchased at jabra.com/ accessories HDMI IN HDMI OUT2 HDMI OUT1 USB A USB A ETHERNET USB C POWER 3.5MM JACK 25 8. Privacy cover When the video bar is not in use, the privacy cover can be used to cover the lenses of the camera. It is recommended not to use the privacy cover while the video bar is in a meeting as it may cause the image from the camera to flicker, which may be triggering for photosensitive individuals. To stop the video feed during the meeting, users can use the in-meeting controls in the video conferencing application. 26 9. Safety capacity settings The JabraPanaCast 50 Video Bar System works together with the video conferencing app to monitor the safety capacity limit of a meeting room. These settings are configured and managed directly in the web portal of your video conferencing service provider. 27 10.Update firmware Firmware updates improve performance or add new functionality to Jabra devices. Jabra PanaCast 50 Video Bar System firmware updates can be done: · Locally on the video bar (mouse required) and touch controller · Remotely using the Web Console for the video bar and touch controller · Remotely using the web portal of your video conferencing service provider For local updates, access the Device settings menu on the touch controller and video bar, go to the System section and select Update. This process must be done individually for both devices. For remote updates, access the Web Console of the video bar and touch controller individually. Enter the IP address of the video bar and touch controller in a browser. If this is the first time accessing the Web Console, the default username is admin and the password is the last 6 digits of the serial number of the device used to access the Web Console. 28 11.Restart devices To restart the video bar and touch controller, access the Device settings menu on the touch controller and go to the Restart section. Both devices will be restarted. You can also access the Web Console by entering the IP address of the video bar or touch controller in a browser, and go to the System Reset menu. 29 Individual restart of the video bar Press and hold the Reset button on the back of the video bar. Release the button after 5 seconds and a `Restarting' message will be displayed on the monitor. The video bar will restart and play an audio notification when ready for use. The reboot takes approximately 1 minute. 5 sec 30 Individual restart of the touch controller Use a paperclip to press and hold the Pinhole reset button on the back of the touch controller. Release the button after 5 seconds and a `Restarting' message will be displayed on the monitor. The touch controller will flash green and restart. The reboot takes approximately 1 minute. 5 sec 31 12.Factory reset To factory reset the video bar and touch controller, access the Device settings menu on the touch controller and go to the Restart section and select Factory reset. Both devices will be reset. You can also access the Web Console by entering the IP address of the video bar or touch controller in a browser, and go to the System Reset menu. When factory resetting the video bar or touch controller individually, it is necessary to reset the other device to ensure the entire system is completely reset to its factory default settings. 32 Individual factory reset of the video bar Resetting will restore the video bar to its factory default settings. Press and hold the Reset button on the back of the video bar for 20 seconds until the LED flashes pink and the `factory data reset' message is displayed on the monitor. The video bar will restart and play an audio notification when ready for use. The reboot takes approximately 1 minute. 20 sec 33 Individual factory reset of the touch controller Resetting will restore the touch controller to its factory default settings. Use a paperclip to press and hold the Pinhole reset button on the back of the touch controller for 20 seconds until the `factory data reset' message is displayed on the screen. The reboot takes approximately 1 minute. 20 sec 34 13. Support 13.1 FAQ and technical specifications View the FAQ, certifications, and technical specifications at jabra.com/help/ panacast50vbs 13.2 How to care for your Jabra device The Jabra PanaCast 50 Video Bar System is for indoor use only. · Avoid direct sunlight and temperatures above 40°C/104°F or below 0°C/32°F. · Do not expose the camera or cables to rain or other liquids. · Do not position the devices near the vents of a monitor or TV as this may cause the devices to overheat and malfunction. · Clean the surface with a cloth dampened with a mild soap solution. 35 To learn more about the Jabra PanaCast 50 Video Bar System, go to jabra.com/help/panacast50vbs/getstarted 36
Wireless headsets and video conferencing cameras for work | Jabra
Declarations of Conformity