User Manual for WANGMI models including: PSBD-CS021DB Cordless Paint Sprayer, PSBD-CS021DB, Cordless Paint Sprayer, Paint Sprayer, Sprayer
WANGMI Cordless Electric Paint Sprayer, 4.0 Ah Battery Spray Painter with 900ml Container, 5 Brass Nozzles, 3 Patterns and Filter for Home Interior and Exterior, Fence, Deck and Furniture PSBD-CS021DB
WANGMI Cordless Paint Sprayer PSBD-CS021DB User Manual Please read this manual carefully before using the paint sprayer, any improper use may cause equipment damage. 2 . Explosive View: 1 ST2.9*10SCRE 18 O-ring 35 Lock catch 2 Rear cover 19 22 Needle spring 36 Micro-switch 3 Cotton filter 20 Needle set 37 Battery Pack 4 Right cover 21 Gun 38 Battery pack pin 5 Switch plunger spring 22 Pipette 39 Left cover 6 Switch plunger 23 Cup-ring 40 Gun-ring 7 Right side cover 24 Suction pipe splint 41 Stopper 8 ST3.5*10SCRE 25 Sprayer Cup 42 Motor cover 9 Big nut 26 3 flat gasket 43 550 Motor 10 Spray ball 27 Short pin 44 Wind mill 11 Spray nozzle 28 Adjusting knob 45 M4*8 SCRE 12 Barge board 29 Trigger 46 Motor gasket 13 Nozzle seal 30 Spray a knob 47 Wind leaf 14 Needle 31 Left side cover 48 Wind cover 15 Needle insert 32 O-ring 49 Damping ring 16 Needle seat 33 Atomization circle 50 Funnel 17 Bowl seals 34 Vent spring 51 Pin . Technical Parameters Paint Sprayer Part Number: PSBD-CS021DB Rated power: 200W Lithium Battery Part Number: LB-MA4000-5CL Rated voltage: 21V Battery Voltage: 21V Frequency: 50/60 HZ Battery Capacity: 4000mAh Rated speed: 30000 RPM Battery Fully Charge: 34 hours Max viscosity: 120 Din-s Fully Charged Battery Spray: 22.5 Gal Max flow: 1000ml/min Battery with Level Display: Yes Spraying width: 6"12"(20-30cm) Portable Charger Part Number: BC-DC21-SCNU Best spray distance: 9"14"(25-35cm) Charger Input: 100V240V Paint Sprayer Cup Capacity: 30oz(900ml) Charger Output: 21V Warranty: For cordless paint sprayer main part, we offer 90 day returns and refunds, 12 month returns and exchanges, and 7×24 hour quick response customer service. If you have any questions, please contact us via your order or email us wangmi20140508@163.com, we will be always here for you! . What You Get You will get 3 Cordless Paint Sprayer × 1 4.0 Ah Lithium Battery with Indicator Display × 12A Battery Charger × 1,;900ml Paint Sprayer Cup × 1Brass Nozzles × 5Plastic Viscosity Cup × 1Cleaning Brush × 1 Cleaning Needle × 1Paper Paint Filter × 5User Manual × 1 In addition, we also offer additional accessories to buy, such as 4.0 Ah Battery , Paint Sprayer Cup, Paper Paint Filter, and Paint Filter Bag. You can find these accessories in our store, or you can contact us by email. . Warm Tips 1. Before spraying, the surface dust should be cleaned up. The result of spraying largely depends on the smoothness and cleanliness of the surface to be coated. 2. Before spraying, please add some water (or paint thinner) to dilute the paint and stir to ensure that your paint passes through the viscosity cup smoothly within 100 seconds. 3. Before using, please select the appropriate size of brass nozzle and spray pattern, check whether the container and paint spray gun parts are tightened. 4. Before using, practice the spray gun on cardboard or similar surfaces to check if the paint has been diluted to the appropriate viscosity. 5. During using, move the spray gun horizontally or vertically evenly according to the setting of spray mode. The uniform motion of the spray gun produces a uniform surface quality. 6. After spraying, remove the battery firstly, then clean the machine immediately to effectively prevent blockage. All components of the sprayer are detachable. Please use a cleaning brush and needle for proper cleaning to remove residual paint from containers, pipes, and nozzles. Use warm soapy water for latex materials, and mineral spirits for oil-based materials. Special Attention: When the paint cup is filled with paint, the paint spray gun should not be inverted. The spray gun must be held in the forward direction to avoid liquid blocking the air inlet, resulting in inability to discharge or damage to the paint spray gun. . How to Dilute Different Fluids Before spraying, add some water (or paint thinner) to dilute the paint, please refer to the following thinning chart and picture. Fluid Run Out Time(Sec) Oil Enamel 25-60 Oil Based Primer 30-60 Oil Stain No thinning required Clear Sealer No thinning required Polyurethane No thinning required Varnish 20-60 Lacquer sanding sealer 25-35 Lacquer 25-35 Automotive finishes 20-40 Latex 45-90 4 . How to Choose Spraying Nozzle Nozzle Size 1.0mm 1.5mm 2.0mm 2.5mm 3.0mm Suggested Fluids Primer, Varnish, Oil-based Pigments, Cleaning Agent Sealers, Stains, Enamel, Dyes Polyurethane, Chalk Paint, Milk Paint, Automotive Paint Low Viscosity Primer, Latex Wall Paint, Oil-based Lacquer Low Viscosity Primer, Latex Wall Paint, Emulsion Paint Reference viscosity 20-30 Din-s 30 Din-s 40 Din-s 40-50 Din-s 70-80 Din-s Recommend Project Table, Chair, Bicycle, Shutter, Cabinets, Wooden Artwork, Model Table, Chair, Bicycle, Shutter, Cabinets, Wooden Artwork, Model Railings, Multi-frame, Window Framer, Pipe, Boat, Yard, Furniture, Garage door, Metal Garden Fences, Door Internal Wall, Wooden Garden Fence, Wooden Pile, Corridor External Wall, Outdoor Floor, Sports Field Line Note: (1) The above applicable fluids and project scenarios only represent our suggestions, and you can make adjustments according to your actual situation. (2) This paint sprayer supports a maximum of 120 Din-s, you should ensure that your paint passes through the viscosity cup smoothly within 100 seconds. . How to use 1. Installing and Removing the Battery (a) Install the battery: Align the base of the spray gun with the battery card slot, push the battery parallel and inward towards the red button position, until you hear a click to indicate that the battery is installed in place (b) Remove the battery: Hold the sprayer with one hand, while the other hand press the battery red button and pull it outward parallel to separate the sprayer and battery A. Install the battery B. Remove the battery 2. Installing and Removing the Motor (a) Remove the motor: Hold the gun with one hand, press the latch in the direction of the arrow, and hold the motor handle with the other hand. Rotate it counterclockwise by 90 º and pull it out forcefully to remove the motor from the spray gun (b) Install the motor: Hold the gun with one hand, press the latch in the direction of the arrow, and hold the motor handle with the other hand. As shown in the figure, the motor handle is perpendicular to the spray gun, aligned with the insertion slot, and rotated 90 º clockwise to make them a straight line, which is locked 5 A. Remove the Motor B. Install the Motor 3. Replace spraying nozzle (1) By default, a spraying nozzle is already installed on the paint sprayer received by the user. If you feel that the size of the nozzle does not match your project, you can replace the nozzle yourself. (2) Rotate the big nut of the sprayer head counterclockwise until the nut is separated from the sprayer, pull out the nozzle kit, remove the small seal ring and spray ball in turn, replace the appropriate nozzle and reassemble the nozzle kit, align the slot and insert the sprayer, install the big nut, rotate and tighten clockwise (3) The nozzle kit can be installed vertically or horizontally, which will result in the paint spraying pattern being horizontal or vertical. It is also very simple to switch between these two installation methods. Loosen the big nut counterclockwise until you can rotate the nozzle kit according to your needs, and then tighten the big nut clockwise and inward Replace Spraying Nozzle 4. Installing and Removing the Sprayer Cup (1) Install the spray cup: Hold the spray gun with one hand, align the spout of the spray cup with the cover with the other hand, and tighten it counterclockwise (2) Remove the spray cup: Hold the spray gun with one hand and loosen the spray cup clockwise with the other hand until they separate 5. Adjusting the direction of the suction tube (a) Upward spraying project: You should open the lid of the cup, rotate the inclined tip of the suction tube and make it point towards the handle end (b) Downward spraying project: You should open the lid of the cup, rotate the inclined tip of the suction tube and make it be away from the handle end (c) In most cases, horizontal spraying is not necessary to adjust the direction of the suction tube 6 A: Upward Spraying B. Downward Spraying 6. Pour fluid into container, make sure not to exceed 900ml 7. Adjusting the flow rate of paint spray (a) Rotate the flow thread knob clockwise upwards to reduce the amount and thickness of paint (b) Rotate the flow thread knob counterclockwise downwards to increase the amount and thickness of paint A. Reduce Flow Rate B. Increase Flow Rate 8. Adjusting the spraying patterns (1) When the spraying nozzle is vertical , the side threaded knob "+" sign is at the top , the sprayed pattern is a horizontal oval shape; When the "+" sign rotates to the bottom , the sprayed pattern is circular shape. (2) When the spraying nozzle is horizontal , the side threaded knob "+" sign is at the top , the sprayed pattern is a vertical oval shape; When the "+" sign rotates to the bottom , the sprayed pattern is circular shape. 9. Pull trigger, the paint will spray from the nozzle 7 . Trouble Shooting Problem Cause A. Little or no fluid 1. Nozzle clogged flow 2. Suction tube clogged 3. Fluid flow setting too low 4. Suction tube loose 5. Fluid is too thick 6. Inconsistent paint 7. Cup is loose B. Fluid leaking C. Atomization is too coarse 1. Nozzle loose 2. Nozzle worn 3. Nozzle seal worn 4. Fluid build-up on spray pattern dial and nozzle 1. Viscosity of fluid is too high 2. Fluid flow setting too large 3. Nozzle clogged 4. Too little pressure build-up in cup D. Spray jet pulsates 1. Fluid in cup running out 2. Fluid is too thick E. Pattern runs or sags 1. Applying too much fluid F. Too much overspray G. Pattern is very light and splotchy H. Large cloud of paint 1. Sprayer is too far from spray object 2. Too much fluid applied 1. Moving the paint sprayer too fast 1. Sprayer too close to surface Solution 1. Clean 2. Clean 3. Rotate the flow knob to increase fluid flow 4. Insert 5. Dilute paint 6. Strain paint 7. Tighten the cup 1. Tighten 2. Replace 3. Replace 4. Clean 1. Dilute paint 2. Rotate the flow knob to reduce fluid flow 3. Clean 4. Tighten container 1. Refill 2. Dilute paint 1. Adjust fluid flow or increase movement of paint sprayer 1. Reduce distance 2. Rotate the flow knob to reduce fluid flow 1. Adjust fluid flow or decrease movement of paint sprayer 1. Move sprayer away from surface and reduce paint flow . Warning 1. Keep your workplace clean and tidy, never use the tool in hazardous areas that contain flammable liquids, gasses or dusts 2. Only use paints, solvents or other fluid with a flash point of 73(22) or higher. 3. Never point the paint sprayer at other person or animal, in the event of an injury, seek immediate medical attention. 4. Always read the paint manufacturer's thinning instructions before use. 5. You must clean the paint sprayer thoroughly after each use. . Warranty For cordless paint sprayer main part, we offer 90 day returns and refunds, 12 month returns and exchanges, and 7×24 hour quick response customer service. If you have any questions, please contact us via your order or email us wangmi20140508@163.com, we will be always here for you! 8WPS 文字