Safety Precautions

In this manual, symbols are used to highlight warnings and cautions for you to read so that accidents can be prevented. The meanings of these symbols are as follows:

⚠️ Warning: This symbol indicates explanations about extremely dangerous matters. If users ignore this symbol and handle the device the wrong way, serious injury or death could result.

?️ Caution: This symbol indicates explanations about dangerous matters. If users ignore this symbol and handle the device the wrong way, bodily injury and damage to the equipment could result.

Please observe the following safety tips and precautions to ensure hazard-free use of the equipment.

Disclaimer

We shall not be liable for any error or for incidental or consequential damages in connection with the furnishing, performance, or use of this documentation or the examples herein.

Safety Tips and Precautions

1. ?️ This equipment should not be submerged in water or other liquids.
2. ?️ Do not cover or press the display area.
3. ?️ Do not attempt to remove the cover of this equipment. Any visible attempt of removing will exempt any manufacturer responsibility.
4. ⚠️ If any of the following situations arises, have the equipment checked by an authorized service personnel:
   • Any connector is damaged.
   • The cable/cord is damaged.
   • The equipment has obvious sign of breakage.

Environment

To prevent the risk of fire, electric shock or malfunction, avoid using your equipment in environments where it will be exposed to:

• Extreme temperatures, over the operation range.
• Heat sources such as radiators or stoves.
• High humidity or moisture.
• Excessive dust or sand.

Handling

• Do not place naked flame sources, such as lighted candles, on the device.
• Do not exert undue pressure on the keys and other controls. Also take care not to drop the unit, and do not subject it to shock or excessive pressure.
• Do not overpress the LCD or touch panel, it would damage one or either components.

Cleaning

Use a soft, dry cloth to clean the chassis and LCD/Touch surface. If necessary, slightly moisten the cloth. Adequated LCD liquid cleaner might be used to remove dust and finger prints.

Connection

Don't connect the unit to over the maximum voltage ratings, it will damage the unit and harm to the user. The device is fully protected and ready to be connected to 9-30V DC power.

Security Usage

Don't operate the device while driving. In several countries, it's forbidden to operate any visual device, either forbidden to visualize any content except GPS or similar guidance utility. The manufacturer isn't responsible for any harm caused by the unsecure use of our devices while driving.

Contents

• 1. Introduction - Page 1
• 2. Specification - Page 1
• 3. Installation - Page 2
  • 3.1 Connection - Page 2
  • 3.2 Power on - Page 4
• 4. Adjusting - Page 4
  • 4.1 Keyboard - Page 4
  • 4.2 OSD(On Screen Display) - Page 5
  • 4.3 Basic settings - Page 6
  • 4.4 Advanced Settings - Page 7
• 5. Dimensions - Page 8
• 6. Packing - Page 9
• 7. Certifications - Page 10

1. Introduction

The XF series provides the best interactive HMI solution for any embedded application. The XF series is specially designed to meet harsh environments such as sustaining extreme shock and vibration. By introducing some key features, such as using "all in one" lockable cable, and simple OSD interface for easy and convenience usage, including a dimmer shortcut key and autodimmer features.

2. Specifications

3. Installation

3.1 Connection.

The image displays various connectors including a main 'All in one' connector, USB Touch, VGA Input, Reserved, Power In, Video 1, CCD, and Audio In.

Power supply: main power supply. Connect this line to 10A fused vehicle's power battery.

VGA input: computer or any device with VGA input.

USB Touch: touch controller HMI USB client.

Audio input R: Audio input Right channel.

Audio input L: Audio input Left channel.

Video input AV1: Composite Video input 1.

CCD Input: Composite Video input with *auto-switch and * auto-start feature.

Auto-switch: the monitor will automatically switch to the CCD input when composite Video signal is present on CCD input. The monitor will return to the previous input once the signal isn't present.

Auto-start: the monitor will automatically power on and switch to CCD input when signal is present. The monitor will turn to power-off automatically when the signal isn't present.

Typical connection:

This diagram illustrates a typical connection setup. It shows a car battery (12/24V) connected via a 5A fused line to a power distribution point. From this point, connections are made to a PC/DEVICE which has RS232, USB, and VGA ports. The monitor is also connected to this distribution point, with inputs labeled AV1 (VIDEO), AV2 (DVD), and CCD (CAMERA).

3.2 Power on.

Please verify the polarity of the power supply and connections before powering on the unit. After connecting the power supply, there are different ways to power on the monitor:

1. Connect the VGA to any VGA source.
2. Connect the Rear camera input to a CVBS source.
3. Press the ? [power] button until the monitor powers on.

4. Adjusting

4.1 Keyboard.

The image shows a vertical array of buttons labeled 1 through 7. Button 7 is at the top, followed by buttons 1, 2, 3, 4, 5, and 6 at the bottom.

1. Power on key.
2. Show OSD window.
3. Increase Volume/OSD Parameter.
4. Source switching.
5. Decrease Volume/OSD Parameter.
6. Dimmer.
7. Power on Indicator/LED.

4.2 OSD (On Screen Display).

The image displays a vertical array of buttons with corresponding labels: LED, Power, MENU, INC, OK, DEC, Dimmer.

4.3. Basic Settings

Color Settings

• Brightness: 85
• Contrast: 50
• Color Temp: 6500K

Adjust Settings

• Auto Config
• H Position: 50
• V Position: 50
• Phase: 0
• Clock: 50

OSD Settings

• Language: English
• H Position: 50
• V Position: 50
• OSD Timeout: 10
• Transparent: Off

Function Settings

• Dimmer mode: Manual
• Time constant: 2
• Threshold1: 12
• Threshold2: 19
• Threshold3: 22

Sound Settings

• Volume: 56

4.4. Advanced Settings.

To enter in advanced mode, press ↖️ and ↘️ simultaneously.

4.4.1. Dimmer options.

The dimmer option allows to configure the values of brightness and backlight intensity for each step:

Left Screenshot:

• Brightness Step1: 10, Step2: 20, Step3: 30, Step4: 40, Step5: 50
• Dimmer Step1: 10, Step2: 20, Step3: 30, Step4: 40, Step5: 50
• userkey, next page

Right Screenshot:

• Brightness Step6: 60, Step7: 70, Step8: 80, Step9: 80, Step10: 85
• Dimmer Step6: 60, Step7: 70, Step8: 80, Step9: 90, Step10: 100
• userkey, prev page, Exit

Instructions:

1. Use ✨ [dimmer] to select the desired parameter.
2. Use ? [menu] to enter in edit mode.
3. Use ←️ and →️ to adjust from 0 to 100.
4. To exit, roll to Exit using ←️ and press ✅ [ok], the settings are automatically stored.

5. Dimensions

5.1 Front/profile.

The diagram shows the front, side, and top/bottom profiles of the monitor. Key dimensions indicated are: overall width 197.800, overall height 157.30, depth 33.450. Mounting hole dimensions and bezel sizes are also detailed.

5.2 Rear

The rear view diagram shows mounting points and dimensions. Two sets of mounting holes are indicated, spaced 75mm apart horizontally and vertically. Other dimensions related to the rear casing are also shown.

6. Packing

6.1 Box unpacking

Images show the process of unpacking the monitor from its box, revealing the monitor and accessories.

Accessories

• Cables
• Power adapter
• Mounting brackets

6.2 Carton packing

Single Unit Carton:

• BOX SIZE: 26X19X10CM
• QTY/CTN: 1 UNITS
• G.W/CTN(kgs): 1.86 (2.5-meter-cable), 2.04 (4.5-meter-cable)
• N.W/CTN(kgs): 1.4 (2.5-meter-cable), 1.58 (4.5-meter-cable)

Multi-Unit Carton:

• BOX SIZE: 26X19X10CM
• Q'TY/CTN: 10 UNITS
• CTN SIZE: 53X42X30CM
• G.W/CTN(kgs): 18.7 (2.5-meter-cable), 21.5 (4.5-meter-cable)
• N.W/CTN(kgs): 18.6 (2.5-meter-cable), 20.4 (4.5-meter-cable)

7. Certifications

European Community Declaration of Conformity

General CE conformity 1999/5/EC.

EMC 89/336/EEC Electromagnetic Compatibility of Information Technology Equipment.

• EN61000-3-2:2000+A1
• EN61000-3-3:1995+A1
• EN55024:1998+A1+A2
• EN55022:1998+A1+A2 Class B

Automotive devices, 95/54/EC / 72/245/EC last amend 2006/28/EC.

ISO 10605, "Road vehicles, Test methods for electrical disturbances from electrostatic discharge"

ISO 7637, "Road vehicles, Electrical disturbances from conduction and coupling".

RoHS

This product is in compliance with the European Union Directive 2002/95/EC on the restriction of use of certain hazardous substances ("RoHS Directive"). Based on information provided by our suppliers, we designate the product as RoHS compliant. Confirmation of compliance status by our suppliers is either because the products do not contain any of the restricted substances referred to in the European Union Commission Decision of August, 18, 2005 (2005/618/EC) in connection with Articles 4 and 5 of the RoHS Directive in concentrations in excess of the values permitted thereunder or because removal of the restricted substances is not technically possible and their existence in the products at levels in excess of these concentrations is allowed as one of the particular applications listed in the Annex to the RoHS Directive.

WEEE

This appliance is labelled in accordance with European Directive 2002/96/EC concerning waste electrical and electronic equipment (WEEE). The Directive determines the framework for the return and recycling of used appliances as applicable throughout the European Union. This label is applied to various products to indicate that the product is not to be thrown away, but rather reclaimed upon end of life per this Directive.

Environment:

• Vibrations MIL-STD 810F 514.5.
• Shock MIL-STD-810F 516.5.
• IP65 according to IEC-529
• Temperature MIL-STD-810F Method 501.4, 502.4

Logos: CE Mark, ? [WEEE Symbol], RoHS Compliant