TS-9210 Mirror Projection Clock

Product Overview and Dimensions

The TS-9210 is a mirror projection clock with the following dimensions:

• Width: 18.5 cm
• Height: 7.7 cm
• Depth: 2.4 cm
• Stand Height: 1.2 cm

The display shows the time (e.g., 12:30 PM), alarm status (AL1, AL2), and has a projection lamp.

Device Components

The device features:

• HORN: Speaker for alarms.
• CR2032 BATTERY COMPARTMENT: For time memory backup.
• Vibrator jack: For vibration alerts (if applicable).
• REMOVABLE SUPPORT FRAME: For positioning the clock.

Display and Button Indications

The display includes indicators for:

• Sound ?
• Shock/Vibration ?
• Alarm 1 (AL1) ⏰
• Alarm 2 (AL2) ⏰
• PM indicator
• Projection lamp

Buttons are labeled for various functions including MODE, AM/PM /DOWN ADJUSTMENT, ALARM/VIBRATION/ALARM+VIBRATION, PROJECT/UP, and SNOOZE/BRIGHTNESS ADJUSTMENT.

Ports include PHOTOSENSITIVE PORT, PROJECTION LAMP, ALARM1/ALARM2, USB OUTPUT PORT, and TYPE-C POWER PORT.

Key Functions

• LED Time Display: Features 6 adjustable brightness levels.
• Function Buttons: Seven buttons for mode, projection, time format (12/24 hr), snooze, volume, and alarm settings.
• Projection Function: Can rotate projection 180 degrees.
• Time Display: 4-digit (hour, minute), switchable between 12-hour and 24-hour formats (default 24-hour).
• Default Time: Clock powers on to 0:00.
• Alarms: Two sets of alarms (AL1 default 6:00, AL2 default 13:00).
• Snooze Function: Adjustable delay from 5 to 60 minutes.
• Automatic Light-Sensitive Function: Adjusts display brightness based on ambient light.
• Night Mode: Automatically switches to low brightness display during set hours.

Power Supply

The clock can be powered via:

1. TYPE-C Power Cord: The primary power source, keeping the device always on.
2. CR2032 Button Battery: Used solely for time memory backup; the product is shipped without batteries.

Power On and Reset

Upon power-on or reset, the display shows:

• LED white light
• Time: 0:00
• Time System: 24-hour format
• Alarm Mode: Sound Alarm

Time Setting

To set the time:

1. In time display mode, long press the [mode] button to enter setting mode.
2. The setting sequence is: 12/24 hour format → Hour → Minute → Exit.
3. Use [+] to increase and [-] to decrease values. Short press for single increments, long press for rapid adjustment (8 steps/second).
4. Settings are automatically saved and the mode exited after 10 seconds of inactivity.

Alarm Setting

To configure alarms:

1. Toggle alarms (AL1/AL2) on or off with a single press of the [al1.2] button. The corresponding alarm symbol will appear.
2. Enter alarm setting mode by pressing and holding [al1.2] for 2 seconds.
3. The setting sequence is: Alarm 1 Hour → Alarm 1 Minute → Alarm 1 Snooze → Alarm 2 Hour → Alarm 2 Minute → Alarm 2 Snooze.
4. Adjust values using [+] and [-] buttons as described for time setting.
5. The default snooze time is 5 minutes.

Alarm and Snooze Operation

• Select alarm mode (sound ?, vibration ?, sound+vibration ??, or off) by pressing the designated button. The selected mode's icon will be lit. If no vibrator is present, ensure sound alarm mode is selected.
• Alarms ring for 2 minutes.
• The alarm symbol (AL1/AL2) flashes when the alarm is active.
• Activate snooze mode by pressing the [Zz.] button when an alarm sounds.
• Press any other button to stop the alarm.

Brightness and Light Sensing

• The LED display defaults to the brightest setting upon power-on.
• Cycle through brightness levels (100% → 80% → 60% → 40% → 20% → 0%) by single pressing the [Zz.] button.
• Turn the automatic dimming function on or off by long-pressing the [Zz.] button for 2 seconds.
• The automatic light-sensing feature adjusts the product's backlight intensity based on ambient light conditions: brighter ambient light results in a brighter backlight, and darker ambient light results in a dimmer backlight.

Night Mode

Night mode enables the LED display to automatically switch to a low brightness setting.

• Toggle Night Mode ON or OFF by single pressing the [mode] button. The default state is OFF.
• The default night mode time is from 18:00 to 6:00, during which the display dims.
• To set the custom night mode interval, long press the [mode] button when Night Mode is ON. The setting sequence is: Start Hour → Start Minute → End Hour → End Minute. The upper indicator lights up for start time settings, and the lower indicator for end time settings.

Projection Function

• Activate the projection function by single pressing the [project] button. The projection brightness is initially set to high.
• Pressing [project] again switches to low brightness. Pressing it a third time turns off the projection.
• Long press the [project] button while projection is active to rotate the projection screen by 180 degrees.
• The projection column can be adjusted: 90 degrees forward and 90 degrees backward.

Charging and Volume Adjustment

• Charging Function: The product includes a USB output port on its side, capable of charging mobile phones or other electronic devices. This port provides an output voltage of 5V when the device is powered via the Type-C cable.
• Volume Adjustment: In time display mode, single press the [VOL] key to adjust the sound level. There are 15 adjustable volume levels (L01 to L15).

Certifications and Markings: FC, RoHS, CE, MADE IN CHINA.