User Manual for Realspace models including: Hdr-Ud1, Electric Adjustable Height Desk, Hdr-Ud1 Electric Adjustable Height Desk, Adjustable Height Desk, Height Desk, Desk
prieš 2 dienas — outlet before use. • DO NOT place the desk in any excessively humid or wet environment to avoid risk of electrical shock.
outlet before use. • DO NOT place the desk in any excessively humid or wet environment to avoid risk of electrical shock.
Electric Adjustable Height Desk User Manual Read Carefully Before Use Keep for Future Reference Safety Information Warning! · DO NOT assemble or use if any parts are missing or damaged. · ALWAYS ensure the desk is placed on flat level ground and is connected to a grounded outlet before use. · DO NOT place the desk in any excessively humid or wet environment to avoid risk of electrical shock. · DO NOT place the desk in direct sunlight or next to a heat source. · DO NOT attempt to repair the desk yourself. Contact customer service or used trained electrical technicians for any service. · ALWAYS switch off the power and disconnect from the power outlet before servicing, moving or cleaning the desk. Specifications Material Min./Max. Height Input Power Output Power Wattage Max. Speed Operating Temperature Range Max. Sound Weight Capacity MDF, Steel 2845 in. (70115 cm) 110240V/5060Hz AC 24V DC 70W 1 ips (2.5 cm/s) 32104°F (040°C) 50 dB 220 lb. (100 kg) 1 Product Diagram 2 No. Name Qty. 1 Base 2 2 Lifting Column (Right) 1 3 Bracket 2 4 Desktop 1 5 Wiring Channel 1 6 Frame (Right) 1 7 Extendable Rod 1 8 Frame (Left) 1 9 Transmission Tube 1 10 Hexagonal Bar 1 11 Rubber Pad 14 12 M5 Washer 13 13 M5×16 Bolt 18 14 M6×10 Bolt 5 15 Lifting Column (Left) 1 16 M6 Washer 14 17 M6×16 Bolt 9 18 Foot Pad 4 19 Power Cord 1 20 Power Adapter 1 21 Control Box 1 22 Handset 1 23 ST5×18 Screw 20 24 Tie 2 25 2 mm Hex Wrench 1 26 4 mm Hex Wrench 1 27 8 mm Hex Wrench 1 28 Wrench 1 29 8 mm Wrench 1 30 4 mm Hex Bit 1 31 Power Adapter Pylon 1 3 Assembly 1. Loosen the preassembled screws in the middle of the frame (6, 8), pull the frame open, then retighten the screws as shown in Fig. A. 2. Put the two lifting columns (2, 15) onto the frame over the preassembled screws. Slide the column brackets so that the screws enter the narrow parts of the bracket screw holes. Retighten the screws as shown in Fig. B. B A B A 3. Screw in the foot pads (18) into the bases (1) as shown in Fig. C. 4. Install the bases onto the lifting columns with the M6×16 bolts (17) and M6 washers (16) as shown in Fig. D. D C 4 5. Turn the assembled frame over and stand it upright. Install the brackets (3) onto the frame with the M6×10 bolts (14) and M6 washers as shown in Fig. E. E 6. Connect the transmission tube (9) to the frame by first placing both ends into the openings on the insides of the columns. Loosen the black plastic knob on the transmission tube to pull out and extend the hexagonal bar (10) to fit the length of the frame. Use the 8 mm hex wrench (28) to turn and adjust the hex opening in the column as shown in Fig. F. Once inserted into the column, use the 18 mm wrench (29) to tighten the hexagonal bar in place with the black knob as shown in Fig. G. At the other end use the 2 mm hex wrench (26) to secure the transmission bar in place as shown in Fig. H. G H F 5 7. Peel off the protective tape on the rubber pads (11) and stick them around the openings on top of the frame brackets as shown in Fig. I. I 8. Place the desktop (4) upside down on the assembly area with the frame on top, ready for attachment. Adjust the length of the frame if needed to align the openings in the frame with the ones in the desktop. Loosen the black knob on the hexagonal bar and the screws on the frame, lengthen or shorten the frame, and repeat the process as shown in previously mentioned Fig. A, B, F, and G. F A B G 6 9. Fix the frame to the desktop using the M5×16 bolts (13) and M5 washers (12). Tighten as shown in Fig. J. You can use the 4 mm hex wrench (27) or the 4 mm hex bit (31) and a power tool (not included) to tighten. 10. Attach the power adapter (20) to the frame using the power adapter pylon (32) and M5×16 bolts. Attach the control box using the same screws next to the power adapter and connect them, as shown in Fig. K. Plug in the motor cord into the control box. 11. Attach the handset (22) as shown in Fig. L and plug in the other end of the cord into the control box as shown in Fig. M. 12. Plug the power cord into the power adapter, then use the ties (25) to tie any loose wires together that would otherwise hang down haphazardly once the desk is turned upright. 13. Loosen the preassembled screws on the frame next to the control box to attach the wiring channel (5), then retighten as shown in Fig. M. N L J K M 14. The 20 ST5×18 screws (24) are included for optional use if you choose to use a seperate desktop instead. 7 Operation Plug the power cord in. The handset will display 70.0, the current height of the desktop in centimeters. Press to enter the menu settings (see below). Press once and press a number key to set the current height in memory. Press & hold to raise the lifting columns. Release to stop. Press & hold to lower the lifting columns. Release to stop. Press to move the desk to a preset height. Reset Pressing to the lowest setting and continuing to hold resets the desk's stored data. Child Lock Pressing and holding and together locks the desk's controls. The handset should display LOC. Repeat this procedure holding and together to unlock the desk's controls. Also note that, if the lifting columns are used for more than 5 minutes consecutively, the mechanism will lock for 18 minutes to prevent overheating. Menu Press and hold until the handset displays S--. Press again to enter the settings menus. In these menus, and cycle through your options and change values, confirms and saves your choices, and escapes to the previous menu without saving changes. 8 Code 1Un 2br Function Unit Selection Brightness Selection Choices Press Notes to change the units displayed. Select to display the desktop's height in centimeters or to display height in inches. Press to change the display's brightness. Select for medium brightness, for low brightness, or for high brightness. Press to change the desktop's sensitivity to collision avoidance while rising. At level 3Fu Sensitivity while Rising L0L9 5, a resistance of about 30 lb. (15 kg) will stop the desktop from continuing to rise. Lower to L1 for greater sensitivity to less resistance or rise to L9 for less sensitivity to more resistance. 4Fd Sensitivity while Lowering L0L9 Press to change the desktop's sensitivity to collision avoidance while descending. 5SH Height Range Press to change the maximum and minimum available heights. is the base height of 70 cm and cannot be changed. can set a height low limit for the desktop if desired. can set a new upper height limit for the desktop. It must be 115 cm or lower and should be at least 10 cm greater than . Press to toggle between manual (01) automatic (02) height control. In manual mode, the and must be 6Hc Height Control 0102 held down to continue movement. In automatic mode, pressing either button begins continuous movement until any key is pressed or the desk's high or low position is reached. 9 Press to change the desktop's bounce height from 520 millimeters. 7H Bounce Height 0520 The bounce height is the amount the desk arises from one single press of the `up' button. Restore 8r Factory Defaults Press twice to reset the desk to its factory default settings. RES will be displayed and the device should be reset as above. 9d Fatigue Test Mode PR_ This setting is only for product testing at the factory. Troubleshooting Problems HOT RESET E01 E06 E07 E08 E09 E10 Possible Solutions Allow 18 min. for the motor to cool. Ensure the ambient temp. does not exceed the desk's range. If the error is still displayed when the motor is well cooled, unplug the desk and then plug it in again. Follow the reset procedure described above. Remove excessive weight from the desk. Check that all cables are correctly and firmly connected. Follow the reset procedure described above. Remove excessive weight from the desk. Ensure the power supply is within the correct voltage range and consistent. Ensure the power supply is within the correct voltage range and consistent. Check that the handset is well connected to the control box. Disconnect and reconnect it while the control box has power. 10 Maintenance · Turn off and unplug the desk before cleaning. · Periodically clean the desk and controls of any dust that may accumulate with a soft cloth. Do not use any liquids or chemicals. · Periodically inspect the desk for any sign of wear or damage. Have any problems repaired or replaced before further use. Contact customer service or use a trained electrical technician. Contact Us Thank you for choosing our products! If you have any questions or comments, contact us and we'll resolve your issue ASAP! 11Adobe InDesign 15.1 (Windows) Adobe PDF Library 15.0