Luxury Home & Kitchen Appliances | Fisher & Paykel USA
Luxury Home & Kitchen Appliances | Fisher & Paykel USALuxury Home & Kitchen Appliances | Fisher & Paykel USA
Installation Guide for FISHER PAYKEL models including: DW60U4HI2, DW60U4HI2 Built Under Dishwasher, Built Under Dishwasher, Under Dishwasher, Dishwasher
Integrated Dishwasher, Sanitise | Fisher & Paykel China
File Info : application/pdf, 18 Pages, 5.84MB
DocumentDocumentBUILT-UNDER DISHWASHER INTEGRATED DW60U4HI2 INSTALLATION GUIDE CN 431862A 11.23 SAFETY AND WARNINGS WARNING! Electric Shock Hazard Failure to follow this advice may result in electrical shock or death. · This appliance must be earthed. This appliance has a cord with an equipment-earthing conductor and an earthing plug. The plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local regulations. · WARNING Improper connection of the equipment-earthing conductor can result in a risk of electric shock. Check with a qualified electrician or service technician if you are unsure if the appliance is properly earthed. · Do not modify the power supply plug provided with the appliance. If a different outlet is required have it installed by a qualified electrician. Do not use an extension cord, adapter plug or multi-box. WARNING! Cut Hazard Failure to use caution could result in injury. · Take care panel edges are sharp. WARNING! Weight Hazard Failure to follow this advice may result in damage or personal injury. · Do not attempt to lift this product unassisted. 3 SAFETY AND WARNINGS WARNING! To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety instructions listed below. Read all the guidance before using the appliance. Servicing z Do not repair or replace any part of the appliance unless specifically recommended in this guide. All other servicing should be undertaken by a Fisher & Paykel trained and supported service technician or qualified person. Installation z Ensure all water connections are turned OFF. It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codes and Regulations. z The dishwasher MUST be installed to allow for future removal from the enclosure if service is required. z The switched power outlet must be outside the dishwasher cavity, so that it is accessible after installation. z This dishwasher is manufactured for indoor use only. z Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord and hoses. z If the dishwasher is to be relocated from one installation to another it must be kept upright to avoid damage from water spillage. z Make sure only new hoses are used for connection (supplied with the dishwasher). Old hoses should not be reused. z Failure to install the dishwasher correctly could invalidate any warranty or liability claims. z Ensure the dishwasher is placed between cabinetry. Failure to do so may result in an unstable product, which may cause damage or injury. z Do not operate this appliance if it is damaged, malfunctioning, partially disassembled or has missing or broken parts, including a damaged power supply cord or plug. z Do not store or use petrol, or other flammable vapours and liquids in the vicinity of the dishwasher. z Connect to a properly rated, protected and sized power supply circuit to avoid electrical overload. z Make sure that the power supply cord is located so that it will not be stepped on, tripped over or otherwise subject to damage or stress. z Do not install or store the dishwasher where it will be exposed to temperatures below freezing or exposed to weather. z Do not use an extension cord or a portable electrical outlet device (e.g. multi-socket outlet box) to connect the dishwasher to the power supply. z This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by providing a path of least resistance for electric current. z This appliance is equipped with a cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local codes and ordinances. z EARTHING INSTRUCTIONS - This appliance must be connected to a earthed metal, permanent wiring system, or an equipment-earthing conductor must be run with the circuit conductors and connected to the equipment-earthing terminal or lead on the appliance. z Ensure the product is not plugged in when fitting custom panels. z Installation of custom panels requires basic mechanical and electrical skills. z Installation must comply with your local building and electricity regulations. 4 z Failure to install the custom panels correctly could invalidate any warranty or liability claims. z Be sure to leave these Instructions with the Customer. z At the completion of the dishwasher installation, the Installer must perform the Final Checklist. z Remove all packaging materials supplied with the dishwasher. z If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle, boat or mobile facility containing the product to the service shop at your expense or pay the service technician's travel to the location of the product. SAVE THESE INSTRUCTIONS The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer. COMPONENTS REQUIRED PARTS z Keep all packing materials until the unit has been inspected. z Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage. z Fisher & Paykel is not responsible for shipping damage. Supplied Not supplied Powered driver Spacers (4) Moisture protection tape (1) Door panel template (1) Sliding bracket (1) Supplied TOOLS Cross-head screw driver Flat-head screw driver Box cutter Toe kick brackets (2) Exit vent (1) Drain hose support (1) 3.9 x 38mm screws (6)* 4mm / 6mm Allen Key 4mm / Phillips Allen Key 4 x 25mm screws (4) 4 x 13 screws (9) 3.5 x 11mm screws (2) 4.2 x 50mm screws (2) Washer (2) Sound seal (2) 3/4" to 1/2" inlet hose adapter (1) *Quantity may differ between models 5 b c k PLAN i a j 6 FRONT PRODUCT DIMENSIONS ISO h e PRODUCT DIMENSIONS A Overall height* B Overall width** C Overall depth** D Height of chassis E Depth of chassis F Height of feet* G Depth of toe kick recess H Depth of inner door** I Height from top of chassis to bottom of inner door J Height from to bottom of inner door to floor* K Depth of door opening** d *depending on adjustment of levelling feet **excluding custom panel and handle MM 820-880 597 554 820 521 0-60 120 33 683 138 639 g f PROFILE Actual product dimensions may vary by ± 2mm CUSTOM PANEL DIMENSIONS Material specifications z Maximum weight of door panels must not exceed 10kg (including handle) z The panel should be adequately sealed to withstand moisture (50°C @ 80% RH). The back and sides of the panel should be completely sealed with a waterproof vapour barrier, such as polyurethane, to prevent damage. z Installation outside these specifications may result in condensation on cabinetry surfaces. c b c h Toe kick considerations z Depending on the desired toe kick recess depth and door panel extension, the toe kick panel height may need to be adjusted to allow adequate door swing. a g a f e ISO d g PROFILE CUSTOM PANEL CONSIDERATIONS A Minimum height of custom door panel for full coverage of the inner door B Minimum door panel width C Door panel depth D Distance from base of door panel to floor E Toe kick panel height F Minimum width of custom toe kick panel* G Minimum toe kick panel depth** H Minimum clearance between top of door panel and benchtop MM 677 596 16-25 65-200 65-200 596 16 2 Weight of door panel (including handle) *Continuous toe kick installations are possible and detailed on page 15. **if using supplied toe kick mounting screws. Panel can be fixed via screwing or gluing to the supplied mounting bracket. 4-9kg 7 DIMENSIONS C CABINETRY CLEARANCES A d B Connections can be located in an adjacent cabinet on either side of the dishwasher*** B A PLAN ISOMETRIC CABINETRY DIMENSIONS MM A Minimum inside height* 820 B Minimum inside width 600 C Minimum overall depth** 580 D Height of toe kick area 65-200 *depending on adjustment of levelling feet **including 19mm door panels on adjacent cabinetry ***For more information on service requirements, refer to 'Plumbing & electrical considerations' and 'Cabinetry preparation'. CABINETRY CLEARANCES A Minimum clearance to adjacent cupboard door B Minimum clearance to corner cupboard 8 MM 2 13 PLUMBING & ELECTRICAL CONSIDERATIONS Hose and cord lengths z Your services can be installed to either the left-hand or right-hand side of the product in an adjacent cabinet. Refer to 'Cabinetry preparation' for service access requirements. z The drain hose should not extend more than 4m. A longer drain hose will cause reduced performance. Water connection z The dishwasher should not be connected to a water system where there is no temperature control, unless the system is fitted with a suitable tempering valve. z The dishwasher must not be connected to an undersink high-pressure push-through hot water system, as damage to the system will result. z Maximum water temperature: 60°C z This product has a 3/4 BSP connector water inlet hose. A 3/4" to 1/2" inlet hose adapter has been supplied for your use if needed. z Ensure water connection complies with local plumbing regulations. Water pressure z 0.03-1MPa Electrical requirements z 230V, 50Hz, 10A Anti-flood protection z This dishwasher has anti-flood protection, which will stop the water flowing in the event of a leak within the machine. d e d e f cb a SERVICE DIMENSION A Length of drain hose B Length of power cord* C Length of inlet hose D Distance from floor to top of hose support E Minimum distance from floor to end of drain hoses** F Minimum inlet hose radius *excluding plug **standpipe install illustrated. Distance is the same for all plumbing installs. f a bc LEFT SIDE MM 1650 950 1450 750883 500 200 RIGHT SIDE MM 1300 1450 1300 750883 500 200 9 z We recommend locating the service holes on either side of the Dishwasher as shown. z If the holes are created through wood, ensure the edges are smooth and rounded z If the holes are created through metal, ensure an edge protector is fitted. 10 SERVICE ACCESS SERVICE HOLE DIMENSIONS A Maximum distance between rear of cavity and service hole* B Maximum distance between floor and service hole** C Minimum diameter of service hole *based on a cabinetry depth of 580mm **depending on adjustment of levelling feet C A REAR WALL B FLOOR PROFILE MM 15 0-50 70 UNPACK PRODUCT CABINETRY PREPARATION Cut straps, lift carton off product and Ensure all minimum cabinetry and 1 remove the top cap. 1 service specifications have been met and that all services will be accessible Dispose of packaging responsibly. after installation. Ensure cabinetry floor is free from 2 Remove the install kit, any internal packaging, all rubber bands and all tape. 2 bumps and obstructions that could prevent the Dishwasher from sliding into the cavity. Align the supplied moisture protection tape to the cabinetry as shown. 3 Ensure this area is free of debris before carefully applying the tape to the surface. 11 DOOR PANEL PREP PUSH INTO CAVITY Using a flat bladed screwdriver, turn to 1 Ensure door panel meets all specifications. 1 raise the leveling feet. Level the rear, outside legs first followed by the front legs. Do not adjust the rear middle leg yet. Remove both screw covers before partially pushing the product into the cavity, pulling the hoses through as you 2 Using the template as a guide, pre-drill all holes into the panel. 2 push to avoid crushing or twisting them. Take care not to bend the legs. Push the product from the outside edges to avoid door damage. Check the product sits level within the cavity. 3 Ensure the sliding bracket is oriented correctly before securing it to the panel. 3 If required, the rear middle leg can be adjusted from the front of the product using a 6mm Allen key. Select desired spacer width and cut Loosely fit both 16mm Philips hanging to size. Remove adhesive and fit two 4 screws onto the door panel. Ensure there is a minimum space of 3 mm 4 spacers to each side of the product. between the screw-head and the panel. Push the product into the cavity from the outside edges. 12 SECURE DOOR PANEL Align the door panel to the product. 1 Slot slider bracket and upper screws into place. Slide the panel upwards to 1 lock into place. Align door panel to surrounding 2 cabinetry. Open door and secure panel 2 to product using 4 x screws. 3 4 FIT EXIT VENT Measure the custom panel overhang from the base of the inner door. Refer to the table below for the recommended cut location. CUT LOCATION 0 1 2 3 4 5 6 7 8 9 !0 !1 !2 !3 OVERHANG (MM) 0 0 0-5 5-12 13-19 20-26 27-33 34-40 41-47 48-54 55-61 62-68 69-75 76-82 On a protected surface, carefully cut the vent at the desired location. Slot the exit vent into the product and secure using two 3.5x11mm screws. 13 BALANCE DOOR SECURE TO CAVITY Use a 4mm Allen key to adjust the door tension. Rotate clockwise 1 to increase tension, rotate 1 Loosely fit 2 x side fixing screws. counterclockwise to decrease tension. Ensure both sides are adjusted evenly. Open the door at a 45° angle and If needed, adjust the Dishwasher within 2 ensure it holds. If the door does not stay 2 the cavity before tightly securing in open, repeat the above step. place. Replace the screw covers. 3 Secure to benchtop using 2 x screws if possible. 14 FIT SOUND SEAL INSTALL SOUND SEAL & TOE KICK CUSTOM TOE KICK PANEL Mark the pilot hole locations for each bracket. Measure the centre of the Align both sound seal sheets to the panel and mark 237mm to each side. 1 base of the dishwasher. If required, trim excess felt. 1 To determine the height of the brackets, measure the height of the lowest bracket hole against the toe kick panel. Ensure door swing is unobstructed 2 before securing the seals using the provided washers and 4.2 x 50mm screws. 2 CONTINUOUS TOE KICK PANEL Align toe kick to product and ensure 3 1 all door swing clearances have been met. Ensure brackets are oriented correctly before fitting to the panel using 2 x screws per bracket. Measure the toe kick depth: toe kick recess panel thickness toe kick depth x - y = z Use Z to determine which tooth to bend back on each toe kick bracket. 2 Fit panel to surrounding cabinetry 4 Align the brackets to the slots on the product and slide into place. 15 PLUMBING & ELECTRICAL CONNECTION Ø38MM STANDPIPE INSTALLATION SINK TRAP/WASTE TEE INSTALLATION Install the drain hose support to the Install the drain hose support to the back wall, as close to the underside of back wall, as close to the underside of 1 the countertop as possible. Refer to 1 the countertop as possible. Refer to 'Plumbing & electrical considerations' for 'Plumbing & electrical considerations' for minimum install heights. minimum install heights. Pull the hose through the drain hose Pull the hose through the support guide support before threading the hose and rest in standpipe. clamp onto the hose and fitting to 2 Ensure the drain hose does not extend into water retained in the trap; an air 2 the sink trap. Secure to trap using the clamp. Ensure hose is routed straight to gap is required to prevent waste water the trap. from siphoning back into the tub. Unplug or drill out the waste tee before securing joiner to sink trap or waste tee. Ensure the rubber washer is fitted when connecting the inlet hose to the tap. Hand-tighten into place. Ensure the rubber washer is fitted when connecting the inlet hose to the tap. Hand-tighten into place. 3 Using a spanner or pliers, turn a further 180° to secure. Avoiding over-tightening. 3 Using a spanner or pliers, turn a further 180° to secure. Avoiding over-tightening. Do not turn water supply on. The Dishwasher must be powered on for the flood protection feature to be enabled. Do not turn water supply on. The Dishwasher must be powered on for the flood protection feature to be enabled. 4 Plug product in. 4 Plug product in. 16 INSTALLER CHECKLIST TO BE COMPLETED BY THE INSTALLER Installation Check all parts are installed correctly and are secure. 1 Ensure all packaging, tape and rubberbands have been removed. Ensure all clearance gaps have been maintained. Ensure Dishwasher is securely fastened to the cabinetry and door opens and closes freely with no resistance. Ensure panel is fitted correctly to the Dishwasher Check the spray arm is in place, mounted correctly and rotates freely. 2 Plumbing Ensure any knock-outs or plugs in drain connection have been drilled out and drain connection has been made. The drain hose joiner must not support the weight of excess hose material. Keep drain hose as fully extended as possible to prevent sagging. Any excess length of drain hose should be kept on the dishwasher side of the drain hose support. Ensure inlet hose has supplied rubber washer fitted, and that it is tightened. If connecting the drain hose to the sink trap, ensure the highloop is a minimum 150mm higher than the drain hose joiner. 3 Water softener models: adjust the water softener setting from the default setting to suit the water hardness of the area. Refer to your user guide. Ensure water supply is turned off until power is connected and turned on. The Dishwasher must be powered on for the flood protection feature to be enabled. Electrical Ensure all electrical tests have been conducted in accordance with local regulations. If site is left without power after installation is complete, ensure water supply is turned off to prevent flooding. TEST OPERATION Turn power and water supply on and open the dishwasher. Select RINSE. After the RINSE cycle has finished, ensure the dishwasher has run and drained correctly. 17 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2023. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. For current details about model and specification availability in your country, please go to our website or contact your local Fisher & Paykel dealer. 431862A 11.23