BTC-A8(S) OMNI BLENDER USER GUIDE

Restricted Substances Information

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed including the following:

• Read All Instructions
• To protect against risk of electrical shock, do not put motor base, power supply cord or plug in water or other liquid.
• Close supervision is necessary when any appliance is used by or near children.
• This appliance is not intended for use by persons (including children) with reduced physical sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• If the power cord is damaged, it must be replaced by the manufacturer or its service or qualified personnel to avoid danger.
• Children should be supervised to ensure that they do not play with the appliance.
• Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or disassembling parts and before cleaning. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.
• Check if the local voltage is suitable for the machine before using the appliance.
• While operating the appliance, do not insert spoons, chopsticks, hard objects or fingers inside the pitcher. These actions are dangerous and could cause damage. The consumer accepts full responsibility in the case of an accident.
• Do not operate any appliance with a damaged cord, plug, when the appliance malfunctions, or the appliance is dropped or damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair, electrical or mechanical adjustment.
• The use of attachments including jars, not recommended by the manufacturer may cause a risk of injury to persons.
• Do not use the appliance outdoors.
• Do not let cord hang over the edge of table or counter.
• Do not place on or near a hot gas, electric burner or in a heated oven.
• Avoid contacting moving parts.
• Keep hands and utensils, other than the tamper provided, out of container while blending to reduce the risk of severe injury to persons or damage to the blender. The cover must remain in place when using the tamper through the cover opening. A scraper may be used but must be used only when the blender is not running.
• To reduce the risk of injury, never place cutter-assembly blades on base without jar properly attached.
• Blades are sharp. Handle carefully.
• Always operate blender with cover in place.

The Functions and Features of the Product

The professional food processor is holistic health cookware. You can effortlessly blend high fiber fruit and vegetable juice, nourishing soymilk, any flavor of smoothie, all kinds of hot soups, a variety of dressings and sauces, nutritious deserts, nourishing tea, healthy whole grains, baby food, and food for the elderly. Super Mum offers you an easy way to mix health and vitality into your life for all seasons.

With this appliance, you can choose a 2 or 2.5-liter pitcher. Materials used include PC-110, TRITAN, or SUS-304. All products have undergone SGS inspection and can withstand heat, cold, and impact without breaking easily.

The core motor possesses a safety system. It automatically cuts power during an electrical overload. After cutting power, you can reset the overcurrent protection button to continue using the food processor.

The core motor also has a temperature guard system. When the temperature exceeds 125°C, it automatically cuts power. You can use it again once the temperature cools down to normal.

The appliance features a rust-resistant cutting head, two exclusively made SUS-440 stainless steel bearings, and Japanese manufactured steel blades.

The patented blade design can chop any food into fine pieces instantly, preparing excellent textures. It is complete with a patented oil seal and a water-resistant design to prevent water or juice from seeping into the bearings and causing premature aging.

It has a patented catch designed for liquid to flow back and a two-step catch for food extraction. You can blend the flow-back contents according to personal needs. Fine pieces of food or food difficult to puree (like soy beans, lemon peel, grass fibers, shrimp, crab shells) can be put through the food catch. This prevents over-blending and oxidation of fruits and vegetables. The food filter can increase the delicate texture of food and make it completely nutritious and not wasteful.

It features two colored lights—a blue and a red LED light—and a fashionable glossy outer appearance. It contains a unique bottom exhaust with three vents for cool air intake and hot air expulsion, increasing endurance and motor efficacy. The control pad is easy to use and understand, with a sturdy and fashionable appearance.

Diagram Explanation

The diagram illustrates the components of the Omni Blender, distinguishing between a PC Jar and a Stainless Steel Jar.

• A. Funnel (Oscillating Feeder): For convenient addition of food.
• B. Small Cap: Holds 50cc of hot or cold contents. Manufactured with polycarbonate (PC-110).
• C. Cover (Lid): Suitable for hot and cold contents, with an excellent fitting seal and easy to clean. Made from heat-resistant TPR material.
• D. Pitcher: Designed for large volumes, suitable for hot and cold substances, and withstands high and low temperatures. Easy to clean. Available in polycarbonate (PC-110), TRITAN, or SUS-304.
• E. Stir Stick: Used to mix food or smoothies and prevent food from getting stuck. Must be used with the pitcher lid in place.
• F. Food Filter: Used to blend and extract natural nutrients, making food particles finer and improving texture.
• G. Unique Steel Blade: Made of 420-J2 Japanese stainless steel with small serrations. Features two SUS-440 bearings in the base, which are rust-resistant and made with zinc alloy.
• H. Retainer Nut: Stabilizes the blade and secures the jar to the base.
• I. Motor-Driven Axel: Powers the blade.
• J. Power Switch: TIMING/OFF/INFINITY. Includes a current protector that cuts power during overload and a temperature sensor that cuts power above 125°C.
• K. Intelligent Timer Switch: Offers settings for 35 seconds (basic), 60 seconds (medium), and 120 seconds (high).
• L. Speed Control Knob: Allows adjustment from speed 1 to 10, suitable for all foodstuffs, from chunky textures (minimum setting) to very fine textures (maximum setting).
• M. Main Motor Base: Houses the motor and controls.
• N. Scraper: Used for scraping ingredients.

A Description of Each Part of the Product

• A. Funnel (Oscillating Feeder): Makes it convenient to put in food.
• B. Small Cap: Can contain 50cc of either hot or cold contents. Manufactured with polycarbonate (PC-110). When blending, it prevents foodstuffs or liquids from spurting out and allows heat to disperse. It has undergone SGS testing and is below regulatory limits.
• C. Cover, Lid: Suitable for both cold and hot contents. Features an excellent fitting seal and is easy to clean. Made with heat-resistant TPR material and has undergone SGS testing, meeting regulatory limits. Easy to put foodstuff inside.
• D. Pitcher: Designed to contain a large volume. Suitable for both hot and cold substances and designed to withstand high and low temperatures. Easy to clean. Available in polycarbonate (PC-110), TRITAN, or SUS-304. SGS tested according to FDA methods and meets regulatory limits.
• E. Stir Stick: Used to mix food or make smoothies and prevent food from getting stuck. The pitcher must be covered with a lid when using the stir stick.
• F. Food Filter: Used to blend and extract natural nutrients. It makes food particles finer and improves texture. Its two-step catch design allows adjustment based on water amount. It can handle ingredients like shrimp shells, grass fibers, fruit pits, and beans.
• G. Unique Steel Blades: Made of 420-J2 Japanese stainless steel, hardened with electrolytic surface treatment, featuring small serrations. Paired with unique technology, the two SUS-440 bearings in the base are rust-resistant and made with zinc alloy. This combination provides superior grinding capacity and strength, breaking down any foodstuff and releasing nutrients.
• H. Retainer Nut: Stabilizes the blade and ensures jars are firmly fixed to the base.
• I. Motor-Driven Axel: Powers the blade.
• J. Power Switch (TIMING/OFF/INFINITY): Acts as a current protector, automatically cutting power during electrical overloads. Also features a temperature sensor that cuts power when the motor's temperature exceeds 125°C.
• K. Intelligent Timer Switch: Offers preset times: 35 seconds (basic), 60 seconds (medium), and 120 seconds (high), suitable for various needs.
• L. Speed Control Knob: Allows adjustment from speed 1 to 10, suitable for all foodstuffs. Use a minimum setting for chunky textures and a maximum setting for very fine textures or larger quantities.

Proper Usage of the Product: Precautions to know before usage

After putting food into the jar and ready to blend, cover the pitcher before inserting the stir stick. Only turn on the power when the pitcher is firmly in place. If you need to add more food while the processor is in motion, retrieve the stir stick first. Then, place the funnel into the lid's hole to add more. Once finished, remove the funnel and replace the stir stick or small cap. Ensure the power is cut off before safely removing the mixture from the pitcher.

Visual Description: A diagram shows a pitcher being filled, then a lid being placed, followed by the motor base, and finally the blender operating with ingredients inside.

• When utilizing the food processor, check if the lid is sealed tightly after adding food.
• When blending hot foods, do not insert the stir stick. If heat pressure builds up, steam will spurt out, causing an accident.
• You can insert the funnel to allow steam to disperse when processing hot foods; do not block the opening of the coverlid.
• You can insert the small cap to allow steam to disperse when processing hot foods; do not block the opening of the coverlid.

Proper Usage of the Product: Controls and Operation

Before taking the plug out of the base: Please first unscrew the tension disc (either unscrewing from the left or right works).

Controls:

• Power switch: UP (TIMING), CENTER (OFF), DOWN (INFINITY).
• Speed Control Knob: MIN and MAX settings.
• Intelligent Timer Switch: 35/60/120 sec.

Two-stage LED Light: Blue (during setting), Red (activated).

The bottom of the machine: Features an overcurrent protection button.

Operation Note: If an overload of the current occurs, it automatically cuts the power. When the current overload protection button pops out, you can press it back into place and continue using it.

Instructions on Food Preparation

Place the prepared food into the pitcher. Cover the food processor with the lid. Set the bottom of the pitcher into the latch of the motor base and ensure it is firmly fastened and tightly sealed.

• If there is a lot of hard foodstuff or large chunks of food, set the motor speed to maximum.
• When preparing cold fruit or vegetable drinks, place ingredients into the pitcher. Pour in liquid (water, juice, or milk) and a small amount of ice, ensuring the water level covers the blades. Insert the stir stick, turn on the power, and turn the knob clockwise from low to high. Once pureed, add cold water and ice according to desired volume and thickness.
• Turn the speed control knob counterclockwise and switch the left side button to OFF to turn off the power. After removing the pitcher, take off the cover and pour out the drink.

Visual Description: A sequence of images shows adding ingredients to a pitcher, sealing the lid, placing it on the base, switching the appliance on, and finally the blender operating.

• When utilizing the food processor, check if the lid is sealed tightly after adding food.
• Switch on from MIN to MAX.
• Switch off.

Instructions for Making Smoothies

Place ice cubes, fruit, and cut-up food into the pitcher. Add liquid (water, milk, or jam) to half the amount of ice cubes.

• Firmly close the lid and ensure it is sealed tightly. Set the base of the pitcher into the latch of the motor base and check for a firm fit.
• Turn the TIMING or INFINITY switch clockwise slowly to the maximum setting.
• First, puree the fruit, then add small ice cubes. If the fruit puree reaches the 500cc mark, add ice cubes up to the 1,000cc mark. Cover with the lid, start the appliance, use the stir stick, and press it in or make circular motions to aid stirring. (For best results, add liquid with half the amount of ice cubes.)
• Turn the knob counterclockwise to OFF. You can then turn off the appliance by turning the switch to OFF, located between TIMING and INFINITY.

Visual Description: A sequence shows adding ingredients to a pitcher, sealing the lid, placing it on the base, switching on the blender, and the final blended smoothie.

• When utilizing the food processor, check if the lid is sealed tightly after adding food.
• Switch on from MIN to MAX.
• When you have completed blending the puree and the fruit juice reaches the 500cc level, add ice cubes until the mixture reaches the 1000cc mark, making 1000cc of liquid. (The best results are when the liquid is half of the ice cubes.)
• Switch off.

You can also cut the fruit up, freeze it, and then put it in the pitcher. Add liquid to half the amount of fruit. Cover with the lid. When in use, help press with the stir stick.

Instructions for Grinding

When grinding, place roasted foodstuff inside. Drier foodstuff yields better results.

• Fill about a third of the pitcher with foodstuff, ensuring it covers the blades. Make sure the cover is tightly sealed and insert the stir stick or the small cap.
• Ensure the pitcher base is properly set into the latch of the motor base.
• Turn the TIMING or INFINITY switch up and down, and turn the speed control knob clockwise to maximum to grind foodstuff into powder or puree.
• Turn the knob counterclockwise to OFF. The light will turn blue. You can then switch off the power. Remove the pitcher and take off the lid to pour out the drink.

Visual Description: A sequence shows adding dry ingredients to a pitcher, sealing the lid, placing it on the base, switching on the blender, and the final ground product.

• When utilizing the food processor, check if the lid is sealed tightly after adding food.
• Switch on from MIN to MAX.
• Switch OFF.

Care Instructions

• To clean the appliance automatically, fill the pitcher half full with clean water, start the INFINITY mode, and turn the knob to MAX. It will clean itself in ten seconds, repeating twice. If there is an odor, add two slices of lemon and clean water, then mix to eliminate the odor.
• For manual washing, fill the pitcher 60 percent with water, cover with the lid, and shake a few times.
• To maintain the bearings, set the pitcher on the motor base after cleaning and pouring out water. Have the motor spin for three seconds to dry, then remove the pitcher. Wipe the inside, outside, and bottom of the pitcher with a dry rag.
• Keep the appliance clean and dry when not in use.
• Food particles can accumulate on the food catch due to grease, pigment, and sticky substances, potentially causing discoloration if not cleaned properly. Use a toothbrush and clean water to wash out food remains immediately after use.

Visual Description: Three circular images depict cleaning instructions.

• A red cross over a blender indicates: When cleaning the appliance, do not soak the power axel in water.
• A blender being filled with water indicates: Fill the pitcher with clean water and start the machine to clean it.
• A pitcher being filled with water indicates: To clean the pitcher, you can add water into it to avoid submerging the bottom retainer nut.

Easy Methods of Preparation

• Making powders: Foodstuffs like medicinal materials, dried rice, and beans must first be baked in the microwave or oven until dry. Place the foodstuff directly into the pitcher with an appropriate grinding amount (at least three centimeters over the blades). Cover the pitcher with a lid. Press the INFINITY mode start button, turn the knob to maximum speed, and mix until it becomes a powder. Longer mixing results in finer powder.
• Blending jam purees: Fruits with high water content like strawberries and oranges do not require added cold water. For kumquats, fill to the half-level mark, add crystal sugar, and mix until fine. Pour into a container and steam in a double boiler for 10-15 minutes, then let cool.
• For spicy pepper, garlic, etc.: Add a small amount of oil. Add foodstuff to the pitcher, cover with the lid, turn on the appliance, and set it on high to smash into pieces until it becomes a puree.
• Oily foodstuffs (peanuts, sesame, etc.): Add 300 grams of fried sesame seeds or 100 grams of fried peanuts and 100 grams of crystal sugar to the pitcher. Adding 50 cc of coconut oil is recommended, but optional. Turn on the INFINITY switch, then turn the knob to maximum speed. Before the mixture breaks down, use the stir stick to stir the sesame powder, pressing down from all four corners to make it into a spread.
• Making condiments: Condiments like mushrooms, small dried fish, small shrimp, scallops, and crystal sugar can be mixed to make seafood-flavored MSG. Star anise, cloves, pepper, and peppercorn can be mixed for seasoning. Cinnamon, orange peel, star anise, cloves, pepper, and tealeaves can be mixed to make a marinade pouch. Foodstuff must be baked before grinding.
• Making soymilk and whole grains: Wash soybeans or whole grains; no need to soak. Boil them in water for five minutes or cook thoroughly. Add 250 grams of foodstuff to the pitcher. Do not place foodstuff into the food catch (refer to p.08 for its use). Add other desired ingredients like cooked pumpkin, sesame, sugar, or vegetables. Pour in 1,000cc of hot water, cover with the lid and small cap. Start the appliance and turn the knob to maximum speed. After one minute of mixing, adjust the knob to minimum speed and rotate slowly. (Adjust speed according to texture preference.) Take out the small lid and insert the oscillating feeder (funnel) to add another 1,000cc of hot water. Mix again for one minute. Total volume will be 2,000cc. This process takes about two minutes.

Troubleshooting

• What happens when the appliance suddenly stops in operation and I cannot get it to work?
  Reason: 1. Too much food or added too quickly on low speed, causing current overload, or motor overworked and overheated above 125°C. 2. Plug not correctly inserted or loose.
  What to do: If current overload, press the overcurrent protection button and continue. If the motor overheats, it will automatically cut power. Wait fifteen minutes for the motor to cool down before it automatically turns back on.
• What if I have plugged the food processor in and the pitcher is in place but the power switch still does not work?
  What to do: Check if the power to the base is properly connected. Check the overcurrent protection button behind the base (see p.05) to see if it is popped out. After pressing the button down, try starting the appliance again.
• What to do if the food processor does not rotate smoothly or produces a strange, loud sound unlike that of when it was new.
  What to do: Inspect the bottom (underside) of the pitcher. Check if the blade or retainer nut has become loose. If the bearing (a consumable component) has deteriorated, replace it.
• Under the circumstances that the power has not been cut, the fuses and overcurrent protection button have not been cut, and the plug has not fallen out of the socket and the appliance still does not work, contact the company or sales location. Do not dismantle it yourself.

Product Warranty Card

Products: _________________________ Model No.: _________________________ SN: _________________________

STAMP

DATE: NAME: TEL:

-Our guarantee is as follows
This product is inspected by the CNS.

1. If the product under normal use in the abnormal situation.
2. Product specifications based on the content of consumer use. One year of non-operating by warranty service. Sales are entitled to six months free warranty service.
3. Consumers as a result of the following reasons damage to the product, the company does not provide free warranty services:
   a. If the user's personal negligence caused the product has been damaged.
   b. Because of the impact caused undue damage to the product.
   c. Did not follow the instructions to use, resulting in damage to the product.
   d. Consumers themselves or by non-maintenance personnel designated by the Company dismantling the host and cause damage.
   e. Consumable parts are not included in the warranty, such as the accessory itself is defective, can be replaced.
4. Receiving warranty service, be sure to provide the product warranty card.
5. Please keep this product warranty card.

Service record card

Manufacturers and Specifications

Manufacturers: XIN LI KANG INTERNATIONAL CO.,LTD.
Dealer: CHEN PING BUSINESS CO.,LTD.
2F.-3, No.50, Sec. 1, Zhonghua Rd., Tucheng Dist., New Taipei City
TEL: 886-2-2265-7793 ; 0800-006-058
FAX: 886-2-2265-2559

• Model No.: BTC-A8(S)
• Place of origin: TAIWAN
• In put: 120V, 60Hz
• Power: 1500W
• Unit dimensions: 53X19X24CM
• Packaging dimensions: 42.5X30X34CM
• Unit weight: 5 kg(unit+processing cup)
• Gross weight: 6.5 kg