Instruction Manual for SKYDANCE models including: D4-XE, D4-XE 4 Channel Constant Voltage DMX512 and RDM Decoder, 4 Channel Constant Voltage DMX512 and RDM Decoder, Constant Voltage DMX512 and RDM Decoder, DMX512 and RDM Decoder, RDM Decoder, Decoder
Output voltage. 4 x (12-36)VDC. Output current. 4CH,8A/CH. Input voltage. 12-36VDC. Input current. 32.5A. User Manual Ver 1.0.6. Technical Parameters.
il y a 3 jours — Note: 1. An DMX signal amplifier is needed if more than 32 decoders are connected, or use overlong signal line, signal amplification should not be more than ...
4 Channel Constant Voltage DMX512 & RDM Decoder
Model No.: D4-XE
RDM/Stand-alone function/Two PWM frequency/Linear or logarithmic dimming/Numeric display
Features
Comply with the DMX512 standard protocols. Digital numeric display, set DMX decode start address by buttons. RDM function can realize intercommunication between
DMX master and decoder. For example, DMX decoder address can be set by DMX master console. 1/2/4 DMX channel output selectable. PWM frequency 2000/500Hz selectable. Logarithmic or linear dimming curve selectable. Stand-alone RGB/RGBW mode and 4 channel dimmer mode selectable, which be controlled by buttons with built-in programs, instead of DMX signal. Green terminal, XLR3 and RJ45 port DMX signal input. Over-heat / Short circuit protection, recover automatically.
Technical Parameters
Input and Output Input voltage Input current Output voltage Output current Output power Output type
12-36VDC 32.5A 4 x (12-36)VDC 4CH,8A/CH 4 x (96-288)W Constant voltage
Safety and EMC EMC standard (EMC)
Safety standard(LVD) Certification
EN55032:2015, EN61000-3-2:2014, EN61000-3-2:2013, EN55024 :2010/A1:2015
EN 61347-1:2015 EN 61347-2-11:2015
CE,EMC,LVD
Environment Operation temperature Case temperature (Max.) IP rating
Ta: -30 OC ~ +55 OC T c: +85OC IP20
Warranty and Protection Warranty
Protection
5 years
Reverse polarity Over-heat Short circuit
Weight Net weight Gross weight
0.388kg 0.426kg
User Manual Ver 1.0.6
Mechanical Structures and Installations
RJ45 DMX signal
RJ45 DMX signal
Installation rack
DMX input/output DMX input/output + GND DMX input/output DMX input/output +
Digital display
Setting key
OUTPUT 123 4 WW CW WW CW R G BW
DMX in/out 12345678
DMX in/out 12345678
DD+ GND DD+
DMX in/out
M
1
2
3
21 3
XLR3 male DMX signal
+ + + + -
XLR3 female DMX signal
IN PUT 12-36VDC
165.00 mm
Output White LED Output Blue LED -
Output Green LED Output Red LED Output LED + Power Input + Power Input -
37.00 mm
70.00 mm
Wiring Diagram
OUTPUT 123 4 WW CW WW CW R G BW
DMX in/out 12345678
DMX in/out 12345678
DMX Master
M
D4-XE
+
+
D-
+
IN PUT 12-36VDC
DMX in/out
D+
+
GND
-
1
2
21
D-
-
D+
3
3
AC100-240V
Power Supply 12-36VDC Constant Voltage
W
RGBW LED strip
Note: 1. An DMX signal amplifier is needed if more than 32 decoders are connected, or use overlong signal line,
signal amplification should not be more than 5 times continuously. 2. If the recoil effect occurs because of longer signal line or bad line quality, please try to connect 0.25W
90-120 terminal resistor at the end of each DMX signal line.
Operation
System parameter setting
Long press M and key in the same time for 2s, prepare for setup system parameter: decode mode, output PWM frequence, output brightness curve, automatic blank screen. short press M key to switch four item.
Decode mode: short press or key to switch 1/2/4 channel decode mode("d-1","d-2" or "d-4"). When set as 1 channel decode, the decoder occupy only 1 DMX address, and four channel output the same brightness of this DMX address.
Output PWM frequency: short press or key to switch 500Hz("F-L") or 2KHz("F-H"). Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for camera(No flickers for video).
Output brightness curve: short press or key to switch linear curve("C-L") or logarithmic curve("C-E"). Automatic blank screen: short press or key to switch enable ("bon") or disable("boF") automatic blank screen. Long press M key for 2s or timeout 10s, quit system parameter setting.
DMX mode
Short press M key, when display 001~999, enter DMX mode. Press or key to change DMX decode start address(001~999),
long press for fast adjustment. If there is a DMX signal input, will enter DMX mode automatically. DMX Dimming: Each D4-XE DMX decoder occupy 4 DMX address
when connecting the DMX console. For example, the defaulted start address is 1, their corresponding relationship in the form:
DMX Console CH1 0-255 CH2 0-255 CH3 0-255 CH4 0-255
DMX mode (001~999)
DMX Decoder Output CH1 PWM 0-100% (LED R) CH2 PWM 0-100% (LED G) CH3 PWM 0-100% (LED B) CH4 PWM 0-100% (LED W)
Stand-alone RGB/RGBW mode
Enter stand-alone RGB/RGBW mode only when DMX signal is disconnected or lost.
Short press M key, when display P01~P30, enter stand-alone RGB/RGBW mode.
Press or key to change dynamic mode number(P01~P30).
Each mode can adjust speed and brightness.
Long press M key for 2s, prepare for setup mode speed,
brightness, W channel brightness. Short press M key to switch three item.
Stand-alone RGB/RGBW mode (P01~P30)
Press or key to setup value of each item.
Mode speed: 1-10 level speed(S-1, S-9, S-F).
Mode brightness: 1-10 level brightness(b-1, b-9, b-F).
W channel brightness: 0-255 level brightness(400-4FF). Long press M key for 2s, or timeout 10s, quit setting.
Speed
Brightness
(8 level) (10 level,100)
Stand-alone dimmer mode
Enter stand-alone dimmer mode only when DMX signal is disconnected or lost. Short press M key, when display L-1~L-8, enter stand-alone dimmer mode. Press or key to change dimmer mode number(L-1~L-8). Each dimmer mode can adjust each channel brightness independently.
Long press M key for 2s, prepare for setup four channel brightness. Short press M key to switch four channel(100~1FF, 200~2FF, 300~3FF, 400~4FF). Press or key to setup brightness value of each channel. Long press M key for 2s, or timeout 10s, quit setting.
Stand-alone dimmer mode (L-1~L-8)
Restore factory default parameter
Long press and key for 2s, restore factory default parameter, display"RES". Factory default parameter: DMX decode mode, DMX decode start address is 1, four channel decode,
high PWM frequence output, logarithmic brightness curve, RGB mode number is 1, dimmer mode number is 1, disable automatic blank screen.
RGB change mode list
No.
Name
P01
Static red
P02
Static green
P03
Static blue
P04
Static yellow
P05
Static cyan
P06
Static purple
P07
Static white
P08
RGB jump
P09
7 color jump
P10
Red strobe
No. P11 P12 P13 P14 P15 P16 P17 P18 P19 P20
Name Green strobe Blue strobe White strobe RGB strobe 7 color strobe Red fade in and out Green fade in and out Blue fade in and out White fade in and out RGBW fade in and out
No.
Name
P21 Red yellow smooth
P22 Green cyan smooth
P23 Blue purple smooth
P24 Blue white smooth
P25 RGB+W smooth
P26 RGBW smooth
P27 RGBY smooth
P28 Yellow cyan purple smooth
P29 RGB smooth
P30 6 color smooth
Dimming curve setting
Linear dimming curve
Logarithmic dimming curve
PPW WMM dduuttyy((%%)) PWM duty(%)
110000 9900 8800 7700 6600 5500 4400 3300 2200 1100
Gamma=1.0
10 20 30 40 50 60 70 80 90 100
Brightness(%)
100
Gamma=1.6
90 80 70 60 50 40 30 20 10
10 20 30 40 50 60 70 80 90 100
Brightness(%)
Malfunctions analysis & troubleshooting
Malfunctions No light Wrong color
Uneven intensity between front and rear,with voltage drop
Causes
1. No power. 2. Wrong connection or insecure.
1. Wrong connection of R/G/B/W wires. 2. DMX decode address error.
1. Output cable is too long. 2. Wire diameter is too small. 3. Overload beyond power supply capability. 4. Overload beyond controller capability.
Troubleshooting
1. Check the power. 2. Check the connection.
1. Reconnect R/G/B/W wires. 2. Set corrrect decode address.
1. Reduce cable or loop supply. 2. Change wider wire. 3. Replace higher power supply. 4. Add power repeater.
Made in China
Corel PDF Engine Version 16.1.0.843