Honeywell Portable Evaporative Air Cooler

Parts Description

The diagram shows the front and rear views of the air cooler with numbered parts.

• 1) Water Inlet Hole
• 2) Handle
• 3) Left Side Grill
• 4) Lever for Horizontal Louvers
• 5) Water Tank
• 6) Casters
• 7) Louvers
• 8) Water Level Indicator
• 9) Control Panel
• 10) Right Side Grill
• 11) Water Inlet Valve
• 12) Drain Plug
• 13) Rear Grill
• 14) Power Cord & Plug
• 15) Rear Grill Screws
• 16) Water Fill Door
• 17) Honeycomb Cooling Media

Important Warnings

WARNING: READ AND SAVE THE AIR COOLER SAFETY & MAINTENANCE GUIDE AND USER MANUAL BEFORE USING THIS PRODUCT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY DAMAGE AND/OR IMPAIR ITS OPERATION AND VOID THE WARRANTY. IN CASE THERE IS ANY INCONSISTENCY OR CONFLICT BETWEEN THE ENGLISH VERSION AND ANY OTHER LANGUAGE VERSION OF THE CONTENT OF THIS MATERIAL, THE ENGLISH VERSION SHALL PREVAIL.

WARNING: FOR OUTDOOR MODEL CO48PM, USE ONLY ON GFCI PROTECTED RECEPTACLES.

Use & Operation

Control Panel

The control panel features three knobs: SWING, SPEED, and COOL. The SPEED knob has settings from 0 (OFF) to 3 (High). The SWING and COOL knobs have ON/OFF positions.

Function Buttons

SPEED / ON - OFF

Connect the unit to the power supply and turn the SPEED knob. The fan will start. Select speed from 1 (Low), 2 (Medium), or 3 (High). To turn OFF the unit, turn the SPEED knob to 0.

COOL

Ensure water is added before using Cool mode. Turn the COOL knob to ON to activate evaporative cooling. The water pump will operate, and cooler air will be felt once the Honeycomb Cooling Media is wet.

SWING

Turn the SWING knob to ON to activate automatic left-to-right louver movement. Vertical Air Flow can be manually adjusted using a lever at the front of the unit.

Cooler Location

Position the air cooler correctly. Refer to the COOLER LOCATION section of the separate Safety & Maintenance Guide.

Filling with Water

Using the Continuous Water Supply Connection is ideal for long periods without refilling and helps prevent pump failure due to low water.

CAUTION: Unplug the unit from the electrical power outlet before filling or emptying the water tank.

Continuous Water Supply Connection

For a continuous supply, connect a garden hose to a main water supply.

Procedure:

• Locate the male connector on the garden hose. Insert it into the cooler's water inlet valve. Screw and tighten the valve onto the hose connector, ensuring a secure, leak-free connection. If leaks occur, disconnect, reposition, and retighten.
• Once secured, turn ON the water supply. Water will flow into the tank.
• The cooler will automatically refill when the tank is empty or below a minimum level.
• The water inlet valve automatically stops water flow when the tank is full, preventing overflow.
• Use a minimum flow setting on the water valve; excessive pressure can damage the inlet pressure control system.

WARNING: The maximum water inlet pressure is 0.5 MPa.

Diagram shows a garden hose connected to the water inlet valve of the cooler. Another diagram shows the lower part of the cooler with labels for Water Inlet Hole, Water Fill Door, and Ice Loading Compartment.

Manual Water Tank Refill

Procedure:

• Using a portable container or garden hose, pour water into the water inlet hole at the top of the cooler.
• Check the water level indicator. Do not fill above the "Max." mark to prevent water droplets on louvers.

WARNING: Always ensure the water level is above the minimum (Min.) mark for both continuous and manual refills. Running in Cool mode with inadequate water may cause pump failure.

WARNING: Do not fill the water tank with dirty or salt water, as this can damage the unit and Honeycomb media.

Note: Water capacity refers to the total volume in the tank and distribution system. The level at the "Max." indicator may be lower than the actual capacity.

Cleaning & Draining the Water Tank

For long-term storage, refer to the STORAGE & MAINTENANCE GUIDELINES in the Safety & Maintenance Guide.

WARNING: Before cleaning, switch the unit OFF and disconnect from the electrical socket.

Procedure:

• Move the unit to a draining location. Remove the cap from the Drain plug at the bottom and allow the tank to empty.
• Refill with clean water to the maximum level and drain completely.
• Use a damp cloth to clean the unit's surface. Avoid corrosive elements or chemicals.
• When not in use, store the unit in a dry place away from direct sunlight.

Cleaning the Honeycomb Cooling Media

The appliance includes three Honeycomb Cooling Media pads, located inside the Rear and Side Grills.

Procedure: Follow Steps 1 to 5 for removal, cleaning, and maintenance.

WARNING: Do not run the unit in COOL mode with stale water. Empty and refill with fresh water, especially if the tank has not been cleaned recently.

Diagrams illustrate steps for removing the rear grill and honeycomb pad, showing screws and horizontal bars.

Removing the Honeycomb Cooling Media

1. Remove screws from the Rear Grill.
2. Carefully pull out the Rear Grill.
3. The Honeycomb Cooling Pad is secured by two Horizontal Bars, fixed by screws on the left and right sides. Remove these screws to release the bars.
4. Slide out the Honeycomb Cooling Pad from the Rear Grill. Replace with a new pad by sliding it into the grill grooves. Reattach the Horizontal Bars with screws.
5. Repeat steps 1-4 for the Left and Right Side Grills.

WARNING: DO NOT operate the Air Cooler with any or all Rear/Side Grills removed, or if a grill is loose. This can cause serious injury or dangerous electrical shock.

Technical Specifications

Electrical Wiring Diagram

For USA Outdoor Models Only. This appliance is equipped with a GFCI plug.

Press the TEST button and then the RESET button once every month to ensure proper operation.

The diagram shows the electrical connections for the air cooler, including switches, main motor, swing motor, pump, capacitor, and sensor switch. It is labeled 'Version: 110~120V/60Hz'. A note indicates '*Low water cut-off. Applicable for models with this feature only.'

Contact Information

JMATEK North America LLC

Mahwah, New Jersey 07495 USA

Phone: 1-800-474-2147

Email: usinfo@jmatek.com

Web: www.jmatek.com

© 2016 JMATEK Limited. All rights reserved.

The Honeywell Trademark is used under license from Honeywell International Inc.

Honeywell International Inc. makes no representations or warranties with respect to these products.

This product is manufactured by Airtek Int'l Corp. Ltd. (subsidiary of JMATEK Ltd.)