KERBL Solar Station Quick Start Guide

Get the Kerbl World App

Scan the QR code to download and install the "Kerbl World" app on your mobile phone.

[QR Code for Kerbl World App]

Product Manuals and Information

Scan the QR code and read the operating instructions for the electric fence energiser carefully before use. Visit my-manual.eu to find all instructions regarding the installation and operation of the app under "SMART-Energizer". Instructions for the solar stations (item numbers 441101 & 441103) are also available.

[QR Code for Manuals]

Website: www.my-manual.eu

Product identifiers: SMART-Energizer, 441101, 441103

Registering Your Electric Fence Box

Scan the QR code of the electric fence box. In the app, select the '+' next to 'SmartEnergiser'. The QR code scanner will open directly. The QR code is located on the side of the appliance cover. The device can only be assigned to one account.

[QR Code for Electric Fence Box]

[App screenshot showing device registration]

Connection Cables and Earthing

2x 3m Connection Cables for Fence & Earth

The connection cables are factory-connected to the appliance and must be routed to the outside through the openings (4.1) in the side panel during commissioning.

Earthing

The underground cable is connected to one of the 6 ground rods using an M8 metal eyelet and a connecting screw (4.1). All 6 earth rods must be connected to each other (4.2) and driven into the ground at a distance of approximately 1 metre from each other.

Fence Connection

The fence connection cable is connected to the supplied stainless steel clamping plate (4.1) using an M8 metal eyelet and connected to the conductor material.

[Diagram 4.1: Close-up of connection point with M8 eyelet]

[Diagram 4.2: Illustration of multiple connected earth rods]

Electrifying the Padlock

The padlock can be electrified if required. Connect the pre-assembled connection cable (5.1) to the fence outlet (5.2) and secure with the red knurled nut.

Follow these steps:

1. Switch the energiser's 1-0-II switch to 'II'.
2. Switch your smart electric fence energiser OFF via the app.
3. Close the solar station door and lock it with the supplied lock and insulated key.
4. Switch your smart electric fence energiser ON via the app. The lock is now electrified.

ATTENTION: ALWAYS switch your smart electric fence energiser OFF via the app before opening the lock!

[Diagram 5.1: Internal connection of the cable]

[Diagram 5.2: Connection to the fence outlet]

[Diagram 5.3: App interface showing energiser status]

[Diagram 5.4: Electrified padlock on the solar station door with warning sign]

Mounting the Plastic Strip

To ensure that vegetation does not impair the performance of the solar module, mount the plastic strip at the bottom of the plastic pallet in the 3 provided holes using the 3 wood screws supplied.

[Image showing plastic strip being mounted with wood screws]

Solar Station XL (Art.Nr. 441101)

1-0-II Step Switch

The step switch controls the output energy:

• I=AN-Low: Reduced output energy 50%
• 0: OFF
• II=AN-High: Maximum output energy 100%

[Image of the 1-0-II step switch with labels]

Solar Station XXL (Art.Nr. 441103)

1-0-II Step Switch

The step switch controls the output energy:

• I=AN-Low: Reduced output energy 50%
• 0: OFF
• II=AN-High: Maximum output energy 100%

[Image of the 1-0-II step switch with labels]

Connections and Earthing

(A) 12 Volt Battery Connection

(B) Reference Earth

(C) 30cm Earth Rod for Reference Earth

Please press the earth rod into the ground directly next to the station at a distance of at least 50cm from the main earth (refer to section 4.2).

[Diagram A: 12V battery connection point]

[Diagram B: Reference earth connection point]

[Diagram C: 30cm earth rod]

Solar Module Orientation

Position the station so that the solar surface of the module faces South. Ensure that no grass, dirt, trees, or bushes obstruct the sunlight.

[Diagram showing North, South, and SOLAR orientation for the module]

Battery Care and Winter Storage

If the station is to be taken out of operation for an extended period (e.g., winter), it is important to keep the battery charged.

Option 1: Solar Radiation

Switch off the electric fence energiser and place the entire Solar Station in a sunny location, orienting the module towards the sun.

Option 2: Using a Charger (Not Included)

Disconnect the 12V battery from the solar electric fence energiser. Reconnect it only for commissioning after storage.

1. Connect the 230V charger (illustration provided) to the 12V battery using the red (+) and black (-) terminals.
2. Plug the charger into the socket and charge as follows:
   • At least 1 day before storage.
   • At least every 3 months during a break in operation.
   • At least 1 day before commissioning.

   Storage Temperature: Frost-free.

ATTENTION: The 230V charger, including its trickle charge function, can remain permanently connected to the battery during storage.

[Image of Solar Station with solar panel]

[Image of SMART BATTERY CHARGER connected to a battery]