Installation Guide for ETC models including: 7462M2170, XDLT Zoom Lens Tube, XDLT Lens Tube, Zoom Lens Tube, Lens Tube, Tube

XDLT Zoom Lens Tube Installation Guide

7462M2170 Rev A

etcconnect.com

ETC

ETC Installation Guide - XDLT Zoom Lens Tube

16 hours ago — For full instructions on using this fixture, see the Source Four. LED Series 3 User Manual, available for download at etcconnect.com. You may choose to use a ...

1 day ago — For full instructions on using this fixture, see the Source Four. LED Series 3 User Manual, available for download at etcconnect.com. You may choose to use a ...


File Info : application/pdf, 2 Pages, 1.96MB

PDF preview unavailable. Download the PDF instead.

XDLT ZoomLens InstallGuide revA
ETC Installation Guide
XDLT Zoom Lens Tube
The XDLT Zoom Lens Tube provides one-handed zoom operation from 15°­30° for Source Four LED Series 3 fixtures. For full instructions on using this fixture, see the Source Four LED Series 3 User Manual, available for download at etcconnect.com. You may choose to use a balance yoke with the XDLT Zoom Lens Tube. For more information on the Source Four LED Balance Yoke, visit etcconnect.com.
WARNING: The XDLT Zoom Lens Tube is not compatible with Source Four
incandescent fixtures. Use with incandescent fixtures will result in damage to the lens tube and will void the ETC warranty.
WARNING: When adjusting the fixture tilt, be aware that a lens tube adds
weight to the front of the fixture. Use caution to control unintended fixture movement when adjusting the fixture tilt.
AVERTISSEMENT : Lorsque vous ajustez l'inclinaison de l'appareil, sachez que
le nez optique ajoute du poids à l'avant de l'appareil. Soyez prudent afin de contrôler des mouvements involontaires du luminaire lors du réglage de son inclinaison.
Install
Insert the XDLT Zoom Lens Tube (A) into the light engine, and rotate clockwise 45 degrees. Secure with the provided screw (B) and barrel rotation knob (C).
B A
C
Corporate Headquarters n Middleton, WI, USA | +1 608 831 4116 Global Offices n London, UK | Rome, IT | Holzkirchen, DE | Paris, FR | Hong Kong | Dubai, UAE | Singapore New York, NY | Orlando, FL | Los Angeles, CA | Austin, TX | © 2024 Electronic Theatre Controls, Inc. Web etcconnect.com | Support support.etcconnect.com | Contact etcconnect.com/contactETC Trademark and patent info: etcconnect.com/ip | Third-party license agreement info: etcconnect.com/licenses Product information and specifications subject to change. ETC intends this document to be provided in its entirety. 7462M2170 Rev A Released 2024-04

ETC Installation Guide
XDLT Zoom Lens Tube
Adjust the Zoom and Focus
1. Press the button on the locking lever, and then lift the locking lever to unlock the dial.
2. Rotate the dial as needed to narrow or enlarge the field angle.
3. Slide the dial forward or backward as needed to soften or sharpen the beam edge.
4. Press the locking lever back in place to lock the dial in position.

Press button and lift lever

Clean the Lenses

WARNING: Do not use ammonia-based cleaners or other harsh commercial
cleaners. Clean lens only as directed. Commercially available glass cleaning agents should be avoided as they may contain ammonia, other harsh chemical detergents or abrasive agents. These cleaners may damage the glass surface and the Anti-Reflective coatings. Do not immerse or soak the glass in any cleaning solution.

1. If you are using a balance yoke, rotate the lens tube to its limit in one direction (approximately 25 degrees) so that the door on the side of the lens tube will clear the balance yoke.
2. Rotate the door fastener a quarter turn to the right or left, and then open the door.
3. Set the zoom to the narrowest field angle to maximize the distance between the lenses.
4. Remove any dust with a blast of oil-free air or wipe with a clean, lint-free cloth. You can use isopropyl alcohol, distilled water, or a 50%-50% mixture of each to clean the glass surface.
5. Close the door, and then rotate the door fastener a quarter turn to secure it.

Rotate a quarter turn to open door

XDLT Zoom Lens Tube

Page 2 of 2

ETC



References

madbuild