User Manual for VALUE models including: MC-GE-MM Gigabit Ethernet Media Converter, MC-GE-MM, Gigabit Ethernet Media Converter, Ethernet Media Converter, Media Converter
VALUE Gigabit Ethernet Media Converter - SECOMP International AG
VALUE Gigabit Ethernet Media Converter 21.99.1199 User manual Please read the manual before using! The manual may be changed without prior notice. Overview The Gigabit Ethernet Media Converter converts 10/100/1000Base-T electrical signals to 1000Base-FX optical signals. It provides an economic way to extend the network transmission distance from 100m over copper cables to 100km over fiber optical cables. It complies with IEEE802.3 10Base-T, IEEE802.3u 100Base-TX, IEEE 802.3ab 1000Base-T, and IEEE802.3z 1000Base-X. It supports auto full/half duplex, auto MDI/MID-X and can be used for many different applications. Item Specifications MC-GE-MM 10/100/1000M, MMDF 550m~2km, SC/FC/ST MC-GE-SM 10/100/1000M, SMDF 20km~120km, SC/FC/ST MC-GE-WDM 10/100/1000M, SC/FC/ST SMSF20km~120km, MC-GE- SFP 10/100/1000M, SFP slot IEEE802.3 10Base-T, IEEE802.3u,100Base-TX/FX, IEEE 802.3ab 1000Base-T, IEEE 802.3z 1000Base-X, IEEE802.3x Flow Control Standard 1x10/100Base-Tx 1x100B/10000ase-Fx 2x10/100/1000Base-Tx 1x1000Base-Fx 4x10/100/1000Base-Tx 1x1000Base-Fx Technical parameters Optical Parameters UTP: 250m @10Base-Tx; 100m @100/1000Base-Tx Fiber: 2km @MMF; 120km @SMF Ethernet port: RJ45 Fiber: SC/ST/FC/LC(SFP) available Packing list Make sure that you receive the full package in good condition. If anything is missing or damaged, please contact us. Gigabit Ethernet Converter Media 1 Power Adaptor (external) 1 Power Line (internal) 1 User Manual 1 1550nm 1550nm 1550nm 1310nm 1310nm 850nm Options wavelength MC-GE-MM MC-GE-MM MC-GE-SM MC-GE-SM MC-GE-SM Reach 550m 2k m 20Km 40Km 60Km 80-100Km 3k m 10~20km 40~60km 60~100km power -10~-3dBm -10~-3dBm -9~-3dBm -5~0dBm -6~+1dBm -2~+3dBm -12~-4dBm -9~-3dBm -2~+3dBm -2~+3dBm Sensibility -17dBm -17dBm -22dBm -24dBm -24dBm -24dBm -23dBm -23dBm -23dBm -23dBm MC-GE-SM Ports Reach Connector Voltage input Power Operating Storage Dimension External: Card:Internal: DC5V DC5V DC5V MC-GE-WDM 1310/1550nm <3W <3.5W <5W MC-GE-WDM 1310/1550nm -10~+65; 10%~90%, non-condensing -40~+75; 5%~90%, non-condensing MC-GE-WDM 1310/1550nm 71* 96*26mm 71* 96*26mm 71* 96*26mm MC-GE-WDM 1490/1550nm 114*88*26mm 140*110*30mm 114*88*26mm / 114*88*26mm / LED indicator The LED indicators facilitates to monitor the working status and troubleshoot. Refer to the below table for the status of LED indicator. LED Status Description On Fiber port connected and link good FX LINK/ACT Blink Data sending and receiving on fiber port Off Fiber port disconnected or link error On Ethernet port connected and link good TX LINK/ACT Blink Data sending and receiving on Ethernet port Off Ethernet port disconnected or link error 1000 On Data rate is 100Mbps on Ethernet port 100 On Data rate is 100Mbps on Ethernet port FDX On Full duplex on Ethernet port PWR On Power supply is ok Off Power supply error Caution 1. The media converter is for indoor use; 2. Cover the dust cap when the fiber port is not used 3. DON'T stare at the fiber port with naked eyes when it is working, or it may hurt your eyes; 4. WDM media converter should be in pairs. Installation Ethernet Port Connection Connect the network device (work station, hub or switch) to the RJ-45 jack of the media converter by CAT5e or better TP cable. Please use quality RJ-45 and well-made patch cords. It auto identifies MDI or MDI-X cable. 1000Base Tx RJ45 Pinouts 8-pin RJ45 MDI/MDI-X Pinouts Pin Signal Pin Signal 1 TRD(0)+ 5 TRD(2)- 2 TRD(0)- 6 TRD(1)- 3 TRD(1)+ 7 TRD(3)+ 4 TRD(2)+ 8 TRD(3)- Fiber Port Connection For dual fiber port, connect TX of media converter with the RX of the network device, and RX of the media converter with the TX of the network device by a duplex fiber optic patch cord. For single fiber optical port, connect the optical port of media converter with that of the network device by a simplex fiber optic patch cord. Power connections Connect the DC socket of media converter, and power supply with the power adapter. We recommend to use our default power adapter. If not, make sure that the rated input voltage of power adapter is 5V. Trouble shooting 1. Power LED is OFF If installed on a desktop, check that the power adapter is securely connected. If installed in our chassis, check that the unit is fully seated in the slot. Verify that the power outlet has power output. Try using another power adapter. 2. TX LINK/ACT LED is OFF Check if the connected device is powered ON and operating properly. Check that the TP cable is securely connected. Make sure that the TP cable does not exceed 100 meters. 3. FX LINK/ACT LED is OFF Check if the connected device is powered ON and operating properly. Check that the fiber is securely connected. Make sure the TX and RX port is connected correctly. Test if the attenuation on the fiber cable does not exceed the acceptable values. 4. FX LINK/ACT is ON, but still problem in communication Check if the data rate of the both sides is 100Mbps Check if the duplex mode of the both sides is same Check if wavelength of the both sides is same Check if the loss budget off fiber is not exceeded.Microsoft: Print To PDF