Home - Blaupunkt
Instruction Manual for BLAUPUNKT models including: MPA 14120 H Power Amplifier, MPA 14120 H, Power Amplifier, Amplifier
Consult an authorized Blaupunkt dealer for installation or repara- tion. Read the manual carefully before operating the device for the first time. Safety Notes.
23 часа назад — Refer to manual for installation instruction. Examine radio system. Replace or repair accordingly. Examine speaker polarity and repair accordingly. Examine ...
MPA 14120 H - Blaupunkt
File Info : application/pdf, 8 Pages, 976.85KB
DocumentDocumentPOWER AMPLIFIER MPA 14120 H Operating and Installation Instructions CAUTIONS Proper system planning is vital in order to maximize the device's performance and road safety. Plan your installation carefully to avoid compromising performance reliability of the system. Consult an authorized Blaupunkt dealer for installation or reparation. Read the manual carefully before operating the device for the first time. Safety Notes Ensure to follow below safety notes during installation and wiring connection: - · Disconnect the negative terminal of the battery. Refer to the safety notes of the vehicle manufacturer. · Ensure positions of the holes are nowhere near the vehicle component to avoid any damage during drilling. · Ensure cross section of the cable is no less than 2.5mm2 if the positive and negative cables are too long. · Incorrect installation may result in malfunction of the device or the car sound system. Installation and Connection Instructions · Select a dry and well-ventilated location to install the device. · The device must not be installed in overly exposed location such on therear shelf, rear seat etc. · The installation location must be suitable for screw holes and have stable ground support. Integrated Fuse The integrated fuse in the device protects the output voltage and the entire electrical system in case of malfunction. Do not replace damaged fuse with higher current. Disclaimer In no event shall Blaupunkt be liable for any direct, indirect, punitive, incidental, special consequential damages to property or life and whatsoever arising out of or connected with the use or misuse of our products. General Safety Notes Observe the following to protect yourself against injuries : · The supply voltage requirement is 12V DC with grounded negative connection. Unauthorised dismantling or modifying may void the warranty of the device. Blaupunkt is not liable for any loss or damaged caused or resulting from unauthorized reparation or modification to the device. Refer to a Blaupunkt specialist in case of any installation or reparation required. · The device's core components may be damaged when the car is driven on bumpy roads for a prolonged period of time or if it is used to play non-standard volume level. · Please do not operate the car radio under extreme temperature conditions (extremely high temperature or extremely low temperature); ensure the temperature within the car ranges from -10°C to 85°C (Storage temperature : 5°C to 35°C) before connecting to the power supply. · For abnormalities, please refer to TROUBLESHOOTING. Consult a specialist if the problem persist. · Solvents, cleaning and scouring agents as well as dashboard spray and plastics care products may contain materials which can damage the surface and screen of the device. Use only dry or slightly moistened cloth to clean the device. Recycling and Disposal Do not dispose of your old unit in the household trash! Use the return and collection systems available to dispose of the old device. This manual may be updated from time to time without any notice. Visit www.blaupunkt.com for more info. USA & CANADA: This product is not intended for sale in the United States and Canada. If purchased in the U.S. or Canada, this product is purchased on as-is basis. No warranty, whether expressed or implied is provided in the U.S. or Canada. 1 INPUT FUNCTION 1 2 3 4 567 8 9 INPUT CH2 CH1 MPA14120H 4-CH CLASS D POWER AMPLIFIER CH1/CH2 GAIN MIN MAX SPEAKER OUTPUT CH1/CH2 BRIDGE CH1 CH2 PRO PWR GND REM +12V FUSE SPEAKER OUTPUT CH3/CH4 BRIDGE CH3 CH4 10 11 CH3/CH4 GAIN MIN MAX INPUT CH4 CH3 1. CH1 / CH2 RCA Input 2. CH1 / CH2 Gain Control 3. CH1 / CH2 Speaker Output 4. Power / Protect Indicator 5. GND Control SPECIFICATION 6. REM Control 7. +12V Control 8. FUSE 9. CH3 / CH4 Speaker Output 10. CH3 / CH4 Gain Control 11. CH3 / CH4 RCA Input 409mm 205mm 58mm INPUT CH2 CH1 MPA14120H 4-CH CLASS D POWER AMPLIFIER CH1/CH2 GAIN MIN MAX SPEAKER OUTPUT CH1/CH2 BRIDGE CH1 CH2 PRO PWR GND REM +12V FUSE SPEAKER OUTPUT CH3/CH4 BRIDGE CH3 CH4 CH3/CH4 GAIN MIN MAX INPUT CH4 CH3 2 SPECIFICATION · Amplifier · Channel : 4 · PCB Layer : 2 · Max Output Power @ 4 ohms : 250W x 4 · RMS Power 4 ohms : 130W x 4 · RMS Power 2 ohms : 180W x 4 · RMS Power 4 ohms Bridge : 350W x 2 · Signal-To-Noise Ratio : >105dB · Gain Adjust : 300mV - 8V · Total Harmonic Distortion : <0.1% · Damping Factor : >88 Accessories Feature · Class AB Amplifier · Max. Output Power : 1,000W · Frequency Response : 10Hz - 40kHz · Dimension (W x H x D) : 205 x 409 x 58mm · Net Weight : 4.1kg Power · Voltage Supply : 10-14.4V · Idling Current : 0.5A · Fuse : 40A x 2 2pcs Mounting Brackets 4pcs Screws (4x20mm) INSTALLATION Screws (4x20mm) 4pcs Screws (3x6mm) Screws (3x6mm) WIRING DIAGRAM Stereo Mode INPUT CH2 CH1 MPA14120H 4-CH CLASS D POWER AMPLIFIER CH1/CH2 GAIN MIN MAX SPEAKER OUTPUT CH1/CH2 BRIDGE CH1 CH2 PRO PWR GND REM +12V FUSE SPEAKER OUTPUT CH3/CH4 BRIDGE CH3 CH4 CH3/CH4 GAIN MIN MAX INPUT CH4 CH3 CH1 CH2 CH3 CH4 3 WIRING DIAGRAM Speaker Connections CH2 SPEAKER 2~4Ohm CH4 SPEAKER 2~4Ohm CH1 SPEAKER 2~4Ohm CH3 SPEAKER 2~4Ohm INPUT CH2 MPA14120H 4-CH CLASS D POWER AMPLIFIER CH1/CH2 GAIN CH1 MIN MAX SPEAKER OUTPUT CH1/CH2 BRIDGE CH1 CH2 PRO PWR GND REM +12V FUSE SPEAKER OUTPUT CH3/CH4 BRIDGE CH3 CH4 Bridged Mode CH2 SPEAKER 2~4Ohm CH1 SPEAKER 2~4Ohm Mono SPEAKER 4~8Ohm INPUT CH2 MPA14120H 4-CH CLASS D POWER AMPLIFIER CH1/CH2 GAIN CH1 MIN MAX SPEAKER OUTPUT CH1/CH2 BRIDGE CH1 CH2 PRO PWR GND REM +12V FUSE SPEAKER OUTPUT CH3/CH4 BRIDGE CH3 CH4 Power Connection Leads CH3/CH4 GAIN MIN MAX INPUT CH4 CH3 CH3/CH4 GAIN MIN MAX INPUT CH4 CH3 4 WIRING DIAGRAM Ground Connect to RCA output of Head unit Positive Terminal Fuse Connect to Speakers Connect to positive terminal Ground cable to chassis WARNING Do not connect negative charge of the battery to the positive charge before installation. 5 TROUBLESHOOTING If any of the following problem occur, please resort to Troubleshooting for the possible solutions. Consult Blaupunkt authorized dealer if problem persist. Problem No audio output Unstable audio cycle Audio distortion Poor bass response Broken battery fuse Broken amplifier fuse Possible Causes Remote wire failed to work Fuse failed to work Disconnected power wires Missing output from source or audio input not connected Disconnected speaker wires Broken speaker Thermal protection will be activated when amplifier temperature exceeds 90°C Poor audio input High amplifier sensitivity setting, exceed maximum output capability of amplifier Low impedance Improper connection of speaker and amplifier Broken speaker Wrong speaker wire polarity connection causing phase cancellation Low impedance Incorrect power connection Fuse used is smaller than recommended Over drawn current Incorrect power wire Over drawn current Fuse used is smaller than recommended Solution Examine voltage output/connection and repair accordingly. Examine power integrity and reversed polarity, repair or replace fuse accordingly. Examine power wire and ground connections. Replace and repair accordingly. Examine input connection and signal integrity. Replace or repair accordingly. Examine speaker wires. Replace or repair accordingly. Examine radio system. Replace or repair accordingly. Improve amplifier's ventilation accordingly. Examine input connection. Replace or repair accordingly. Refer to manual to reset gain setting. Examine speaker impedance. Rewire speaker accordingly, if below 2 stereo or 4 mono. Examine speaker wire, replace or repair accordingly. Refer to manual for installation instruction. Examine radio system. Replace or repair accordingly. Examine speaker polarity and repair accordingly. Examine speaker impedance. Rewire speaker accordingly, if below 2 stereo or 4 mono. Examine power wire and ground connections. Repair accordingly. Replace with recommended fuse type. Examine speaker impedance. Rewire speaker and replace fuse accordingly, if below 2 stereo or 4 mono. Examine power wire and ground connections. Repair accordingly. Examine speaker impedance. Rewire speaker and replace fuse accordingly, if below 2 stereo or 4 mono. Examine power wire and ground connections and repair accordingly with correct fuse. 6 Blaupunkt Car Entertainment - Asia Pacific Competence Centre 1 121 24 028 41 01