Manuals+

Fine Fixtures Remote Control User Manual

Introduction

This user manual provides detailed instructions for the operation and installation of the Fine Fixtures remote control for smart toilet bidet seats.

Content

Please refer to the following sections for detailed information:

Remote Control Illustration

The remote control features various buttons and indicators for operating the smart toilet functions. Below is a description of its layout:

Main Buttons:

Indicator and Adjustment Buttons:

Function Icons (on remote display/buttons):

Notice: If your toilet includes an auto open/close function, the remote control operates as depicted. Refer to page 8 for operation methods and how to turn off this function.

Installation Preparation

Remote Control Installation

Follow these steps to install the remote control holder:

  1. Drill Holes: Drill two parallel holes on the wall, 35mm deep, with a center distance of 106mm. Ensure the location allows the end-user to reach the remote control comfortably while seated.

    Diagram Description: Shows a wall with two holes drilled, indicating measurements (e.g., 4 inches, though the text specifies mm). A drill is shown.

  2. Install Hanger: Insert expansion tubes into the wall holes. Install the hanger using screws and attach it securely. Apply double-faced adhesive tape to the hanger for additional wall adhesion. Tighten the screws.

    Diagram Description: Shows expansion tubes inserted into wall holes, a hanger being screwed into place, and adhesive tape being applied. Labels indicate 'Hole'.

  3. Install Battery and Remote: Install the battery into the remote control and then place the remote control onto the installed hanger.

    Diagram Description: Shows the remote control with battery compartment open, and then the remote being attached to the hanger. A small 'anti-theft screw' position is indicated.

Notice

Please do not install or use the product in moist environments such as steam rooms, or in areas prone to getting wet.

In public places, use the provided screw to fix the remote control with the bracket to prevent it from being misplaced.

Usage Instructions

Rear/Front Cleaning

Press the "Rear" or "Front" button. Water will spray from the wand to clean the respective body area. The function stops automatically after a cycle. Pressing the [STOP] button will immediately halt the operation.

Massage

Press the [MASSAGE] button to activate the massage function. The nozzle moves forward and back to extend the cleaning scope. Press the [MASSAGE] button again to stop the function.

Drying Operation

Press the [DRY] button. Warm air will be expelled from the wand to dry the area. The function stops automatically after a cycle or when the user leaves the seat.

Diagram Description: Shows the remote control with Rear, Front, Massage, and Dry icons highlighted. Small diagrams illustrate the nozzle action for Rear, Front, Massage, and Dry functions.

Auto Function

The full-automatic function can be activated using the [AUTO] buttons. Users can pre-set nozzle position, water pressure, and temperature. The full-automatic function will engage when the corresponding function button is pressed.

Automatic Cleaning Cycles:

Diagram Description: Shows the remote control with the AUTO button highlighted. Flow diagrams illustrate the sequence and duration of Auto Rear Cleaning, Auto Front Cleaning, and Auto Rear and Front Cleaning cycles.

Energy Saver

Press the [ENERGY SAVER] button. The LCD screen displays energy saver status and options for the energy saver period: 3 hours, 6 hours, or 9 hours (or off). For example, setting the energy saver from 9:00 to 15:00.

Operation Example:

  1. Press [ENERGY SAVER]. The LCD shows the [ENERGY SAVER] icon.
  2. Press [ENERGY SAVER] again. The LCD shows the selected period (e.g., "6 H"). The icon disappears after 3 seconds, indicating successful setting. The toilet enters energy saver mode during the set period, with the power light off and energy saver light on. It returns to normal operation mode afterward.

Diagram Description: Shows the remote control LCD displaying the ENERGY SAVER icon. Another view shows the ENERGY SAVER icon with a time range (9:00 to 15:00) and the 'Energy saver light is on' status.

To Cancel Energy Saver: Press and hold the [ENERGY SAVER] button until the function is cancelled (no display). To change the energy saving time, press the "energy saving" button and select a new figure (3, 6, or 9 hours) until the icon disappears.

Energy Saver Mode: The toilet will automatically enter energy saver mode after setting. In this mode, seat temperature is set to a low status (first level) to conserve energy.

Notice: If a user sits on the seat, the energy saver mode pauses, and the seat heats up immediately. The energy saver mode restores after the user leaves. When set, the energy saver icon automatically disappears, which is normal.

Spray Nozzle Position Adjustment

During "REAR" or "FRONT" operation, press the nozzle position buttons (◀️ and ▶️) to move the nozzle forward or backward across 5 levels.

Water Pressure Adjustment

During "REAR" or "FRONT" operation, press the water pressure buttons (➕ and ➖) to adjust the water pressure for cleaning.

Automatic Deodorization

Remark: The deodorization function activates automatically when a user sits on the seat and stops 3 seconds after the user leaves. This function also stops during drying.

Diagram Description: Shows the remote control with the Deodorization icon highlighted. Small diagrams illustrate the massage function and the deodorization process.

Temperature Adjustment

Press the [TEMPERATURE] button to cycle through temperature settings:

Diagram Description: Shows the remote control and screen indicators for Water, Dry, and Seat temperature adjustments using the TEMPERATURE button and +/- buttons.

Full Flush

Press the "FLUSH" button to activate a full flush.

Auto Lid Open/Close

(Only for toilets with this function)

Diagram Description: Shows the remote control with icons for Lid close, Lid open/seat close, and Lid open/seat open.

Nozzle Cleaning

Nozzle Self-Cleaning by Quick Press: Quick press the "NOZZLE CLEANING" button. The nozzle self-cleans for a short duration and moves to the front position (no spray). Users can then manually clean the nozzle.

Nozzle Self-Cleaning by Long Press: Long press the "NOZZLE CLEANING" button. The spray will not move forward, and the nozzle self-cleans for 90 seconds.

Diagram Description: Illustrates two scenarios for nozzle self-cleaning: one showing a quick press and manual cleaning, the other showing a long press with a timer indicating 90 seconds.

Combination Button

Night Light: Press [STOP] then [DRY] for the night light to be off. Repeat to switch to intelligent state. Cycling through this process toggles between off and intelligent states.

Quiet Mode: Press [STOP] then [MASSAGE] to turn off the buzzer for quiet operation. Repeat to re-enable the buzzer.

User Code: To prevent interference from multiple remote controls, a user code (1-9) can be set. Turn on the toilet for setting and turn off others. Press [STOP] then "REAR" to enter setting mode. Use ➕/➖ to select a code. Press [STOP] then "REAR" again to save and exit. The sum of water pressure and position levels on the LCD indicates the user code. Restart to clear.

Automatic Flush Button: Press [STOP] then "FLUSH" to start or close the automatic flushing function. The toilet will flush automatically after detecting a user for over 6 seconds and after the user leaves the seat for more than 3.5 seconds.

Auto Open/Close: Press [STOP] then the [lid open/seat open] button (or similar icon) to enable auto open/close. Repeat to disable. This function is only for toilets with auto open/close capability and is off by default.

Remark: A flashing signal indicator and a "click" buzzer confirm signal transmission and reception. If the signal does not flash or the buzzer does not sound, re-press the button, ensuring correct direction. In case of a power cut during wand operation, wait for power reset. If the power cut is prolonged, gently push the wand back by hand to avoid damage. The body must touch the seat for cleaning/drying functions to operate. The nozzle may spray for 1-2 seconds after the user stands up; press [STOP] before standing. Use nozzle self-cleaning after the user leaves the seat. If [NOZZLE CLEANING] or [STOP] is not pressed, the wand returns after 10 minutes or when the user sits.

Set Auto Function

Set Automatic Rear Cleaning Function

The default settings include water pressure, nozzle position, water temperature, dry temperature, and seat temperature at level three, with massage function off. Users can customize these settings.

  1. Adjust water pressure, nozzle position, and temperatures using the function buttons. Enable/disable massage function.
  2. After setting, long-press the automatic rear cleaning button for 3 seconds to save.
  3. Subsequently, a quick press of the [person] (Rear) button will activate the saved settings. The toilet will perform rear cleaning for 90s, then dry for 180s, and stop automatically.
  4. During automatic rear cleaning, users can change levels, temperatures, and massage status, then press the "REAR" button for 3 seconds to save new settings.

Diagram Description: Shows the remote control with adjustable parameters highlighted (pressure, position, temperature). An example illustrates settings like nozzle position level 2, massage on, water pressure level 4, water temperature level 2, dry and seat temperature level 1.

Set Automatic Front Cleaning Function

  1. Press the spray nozzle position adjustment button to set the nozzle position. Use ➕/➖ to adjust water pressure and set temperature levels. Enable/disable massage function.
  2. Press and hold the [person] (Front) automatic cleaning button for 3 seconds to save the settings.
  3. After saving, a quick press of the [person] (Front) button will activate the saved settings. The toilet will perform rear cleaning for 90s, then dry for 180s, and stop automatically.
  4. During automatic front cleaning, users can change levels, temperatures, and massage status, then press the "FRONT" button for 3 seconds to save new settings.

Diagram Description: Shows the remote control with the AUTO button and related icons highlighted for front cleaning.

Set Automatic Rear and Front Cleaning Combination Function

Note: Find suitable levels and temperatures by comparing during use. Set the combined automatic Rear and Front cleaning function while using the toilet.

The First Stage: Rear Cleaning 90s

  1. The combination function includes rear cleaning (90s), front cleaning (90s), and drying (180s). Users can adjust levels and temperatures for each stage.
  2. After the user sits on the toilet, press the automatic Rear and Front cleaning button. Rear cleaning begins for approximately 90s.
  3. Adjust nozzle position, water pressure, wind temperature, seat temperature, and enable/disable massage function during rear cleaning.
  4. After adjustments, the remote control saves the parameters for the first stage. If multiple adjustments are made, the latest parameter is saved.

The Second Stage: Front Cleaning about 90s

  1. After rear cleaning finishes, the toilet automatically enters the front cleaning stage.
  2. Users can set nozzle position, water pressure, temperature, and enable/disable massage function. The remote control saves the latest parameter for the second stage.

The Third Stage: Drying about 180s

  1. After front cleaning finishes, the toilet automatically enters the drying stage.
  2. Users can set wind temperature, and the remote control saves the latest parameter for the third stage.

One-Button Operation: After setting all parameters, a quick press of the [AUTO] button will display the saved settings. The toilet will then perform rear cleaning, front cleaning, and drying automatically. Repeat steps 1-3 to change previous settings.

Diagram Description: Illustrates a user sitting on a toilet, followed by a sequence showing rear cleaning, front cleaning, and drying stages.

Contact Information

FINE FIXTURES

206 WEMBLY ROAD - NEW WINDSOR, NY 12553

P: 718.602.6060 F: 718.963.2082 - E: INFO@FINEFIXTURES.COM

TOLL FREE: 1.877.8FIXTURES

FINEFIXTURES.COM

RETAIN THIS INSTALLATION MANUAL FOR FUTURE REFERENCE.

Models: Wave Smart Toilet Remote Control, Smart Toilet Remote Control, Toilet Remote Control, Remote Control, Control

File Info : application/pdf, 16 Pages, 1.46MB

PDF preview unavailable. Download the PDF instead.

A1bEN9IzVlL

References

PDFium PDFium

Related Documents

Preview Fine Fixtures Toilet Seat Installation Instructions
Comprehensive installation guide for Fine Fixtures toilet seats, detailing step-by-step instructions for proper and safe mounting. Learn how to assemble, attach, align, and secure your new toilet seat.
Preview Fine Fixtures Aluminum Wall Mounted Medicine Cabinet Installation Instructions
Comprehensive installation guide for Fine Fixtures aluminum wall-mounted medicine cabinets, detailing surface and recess mounting procedures, including parts lists, tools, dimensions, and door adjustments.