CT602 Floating Bluetooth Lightshow Speaker
Please charge before use.
Introduction
The CT602 is a floating Bluetooth speaker with a light show. It can be used in swimming pools, ponds, yards, parties, indoors, and more, making life more colorful!
Model Number: CT602
1. Introduction to Parameters
A diagram shows the speaker's top view with labeled components:
- DC 5V charging jack
- Light mode button
- Vol-/Previous button
- Vol+/Next button
- Multifunction button
A side view diagram shows the speaker's dimensions:
- Height: 6.63 inches
- Width: 4.94 inches
| Bluetooth version | V5.3 |
|---|---|
| Battery capacity | 2500mAH lithium battery 3.7V |
| Working hours | 5-7 hours |
| Frequency | 2400MHz-2480MHz |
| Protocol | A2DP/AVRCP/HFP/HSP/OPP/HID/SPP/PBAP/GATT/SM |
| Communication distance | 15-25 meters |
| Speaker | Mono mixing output 4Ω6W, high-fidelity waterproof speaker (Φ57mm) |
| Dimension | 4.94"x4.94"x6.63" |
| LED light | Yellow, Green, Red, Blue |
| LED mode | 8 modes |
| Waterproof | IP68 |
Pairing Information:
- It takes about 3 minutes to pair for the first time. After successful pairing, it will automatically pair in the future, taking only 8 seconds.
- After power on, if not paired, it will enter sleep state after 20 minutes and shut down after another 40 minutes.
2. Button Function Description
A. Multifunction Button: ▶️⏸️
- Long press for 3 seconds to power on, and long press again for 3 seconds to power off.
- When playing music, short press to pause music, press again to resume playback.
- When a call is incoming, short press to answer the phone, double press to refuse the call.
- Double tap to redial the last called number.
B. "volume-and previous"Button: ⏪
Short press to play the previous track, long press to reduce the volume.
C. "volume+and next"Button: ⏩
Short press to play the next track, long press to increase the volume.
D. Light mode Button: ?
Short press to switch between different LED modes:
- Slow flashing when there is no music: red, green, blue, yellow gradually brighten every 20 seconds.
- When there is music: the LED lights flash with the music.
- Keep red light.
- Keep green light.
- Keep Blue light.
- RGB light color changes automatically (slow and fast flashing are mixed).
- RGB light color automatically switches slowly.
- RGB light color automatically switches quickly.
- The light power off.
Long press the light button for 8 seconds to restore factory settings. ⚙️
3. Bluetooth Pairing Settings
Long press the multifunction button for 3 seconds to power on. Wait for the blue light to flash, then open Bluetooth mode on your smartphone and select "CT602" to pair the device. It is now paired. You can broadcast your music! If not, start again or relaunch the CT602.
4. Charging
Use the included USB cable. Connect the USB port to a 5V USB outlet and the DC jack to the CT602. During charging, the LED indicator will remain red. When the battery is full, the LED indicator will turn green. ?
Note: Use the included cable and respect the voltage! ⚡
5. Accessories
- 1* CT602
- 1* User manual
- 1* Charging cable
- 1* Gift box
FCC Compliance Information
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. ?
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- (1) this device may not cause harmful interference, and
- (2) this device must accept any interference received, including interference that may cause undesired operation.
CE Made in China ??