Installation Guide for Xtune models including: 13-054, 99-13 Chevy Silverado - GMC Sierra 1500, 99-14 Silverado - Sierra 2500 HD, 01-14 Silverado- Sierra 3500 HD, CS99 99-13 Chevy Silverado, 99-13 Chevy Silverado, Chevy Silverado, Silverado
Please note: Crew cab models (Four Full Doors) will require all of the included mounting brackets. For all other cab models (standard, extended,.
13 hours ago — Please note: Crew cab models (Four Full Doors) will require all of the included mounting brackets. For all other cab models (standard, extended,.
INSTALLATION INSTRUCTIONS ITEM NO: DESCRIPTION: 99-13 Chevy Silverado / GMC Sierra 1500; 99-14 Silverado / Sierra 2500 HD; 01-14 Silverado/ Sierra 3500 HD ATTENTION Please read this installation guide before installing this part. Protect your vehicle properly as scratches to the product or vehicle may occur. You may need to periodically to re-tighten all hardware for safety use after installation. Installation pictures are only for reference, there might be some differences between pictures and the parts you receive as there may have been a revision. · Excluding diesel models with def tanks · Remove contents from box. Verify all parts are present · Read instructions carefully before starting installation · Do not over torque. Standard operating load for tighten body mount nuts & bolts varies from 45 to 65 foot pound · Polished stainless steel-limited lifetime powder coated black-3 years NO PO SIZE QTY NAME NO PO SIZE QTY NAME 1 2 Front Bracket 6 13-054-G1 6 2 2 Middle Bracket 7 HW-081 35*13.5*3 7 Flat Washer 3 2 Rear Bracket 4 4 Front And Middle Auxilary Bracket 5 2 Rear Auxilary Bracket TOOLS NEEDED (NOT INCLUDED) NAME 12 & 19mm Socket Ratchet Extension Wrench 8 HW-063 M8*1.25 13 Hex Nuts 9 HW-032 M8*1.25*30 7 Cup Head Square Neck Bolts 10 HW-080 21*13.5*2.6 7 Spring Washers Please note: Crew cab models (Four Full Doors) will require all of the included mounting brackets. For all other cab models (standard, extended, access, double etc.); while a minimum of two brackets per side are required, we highly recommend using as many of the included brackets as possible on each side for enhanced stability and strength. RH LH INSTALLATION INSTRUCTIONS 1. This instruction will disclose the bracket installation guide. 2. Before installation, please read this instruction in order to install correctly. 3. To ensure the installation process is safe, please pay attention to the following signs. 4. Caution: It may cause car damage or injury to people if the instructions are not followed. 5. Hint: To help with the installation, please be prepared and follow closely. 6. When proceeding with the installation of the part, pay attention to using the tool carefully. 7. Check all the components in the hardware kit to make sure it's complete. If you find any shortages in the kit, please contact the supplier for a replacement. 8. Avoid dropping or knocking this part on the surface to prevent damage. 9. To install the front, middle, and rear brackets, first loosen the original body mount bolt. Insert the #6 M8 bolt plate into the hole, which is for installing the #4 (for front and middle) and #5 (for rear) auxiliary brackets. Please refer to pictures 1 and 2 P1 46 Middle Bracket 46 Rear Bracket 86 1 7 10 9 Front Bracket 8 2 7 8 10 9 Original body mount 9 8 7 10 8 5 3 8 P2 10. When installing the running board, please make sure the screws on the running board stick in the bracket hole. Tighten the screws with proper nuts and tools. Also, align the running board before tightening all the bolts (torque: 11 lb/ft, below P4 11. Periodically check your product because it may need re-tightening of boltsAdobe PDF library 17.00 Adobe Illustrator 28.5 (Windows)